USER’S MANUAL MANUEL DE L’UTILISATEUR MANUAL DEL USUARIO WB84U1D1
Interactive White Board Operating Instruction Before operating the unit, please read this manual thoroughly, and retain it for future reference. Safety Warning Before operating the unit, please read this manual thoroughly, and retain it for future reference. Placement Do not place the unit on an unstable cart, stand, tripod, bracket, table, or shelf. Do not expose the unit to direct sunlight and other sources of heat. Do not place the unit near appliances that create magnetic fields.
Battery Properly maintain the batteries and recycle the used batteries. Caution This is a Class B product , there is not cause radio interference.
CONTENT 1 INSTALLATION ............................................................................................................ 5 1.1 Open the package ........................................................................................................................ 5 1.2 Checking parts ………………………………………………………………………………………………………………………. 5 1.3 Installation....................................................................................................................................
1 INSTALLATION 1.1 Open the package Step‐1: Take out the carton handles. Step‐2: Move‐Up the carton body. Step‐3 : Take Off EPE packing material & Left IWB display . Step‐4: Be careful to Move out IWB display. It is heavy and easy to be slide, Please carefully and better Wear gloves when move display from carton box . 1.2 Checking parts Warranty Card, Quick Connect Guide, Remote Control, Power Cord, VGA/USB/Audio/AV/YPBPR cables, Batteries, handwritten pen and DVD.
1.3 Installation The IWB Stand (matched) takes material object as the standard, Please read “IWB Stand Installing Instruction” while installing. 1.3.
IWB Back View Please follow above picture , Tie‐UP mounting bracket to IWB display by 3 screws on each side insert to #2.#3,#4 screw holes. Fix screws to firm condition. After finished mounting bracket installation, it is easy hang‐up display to movable stand. 1.3.
2 CONTROL PANEL (located at the Front panel) 1 POWER Display power on/off 2 VOL+/VOL‐ Sound Volume adjustment 3 P+/P‐ Menu Item up/down selection 4 MENU To enter / exit MENU Page 5 SOURCE To switch input source 6 Main Switch for Power on/off (one): ON, 0 (zero): OFF 8
3 INPUT / OUTPUT TERMINALS Rear Bottom Terminals Rear Right Side Terminals 1. USB TOUCH USB terminal for touch panel. (USB: DC5V, 500mA) 2. RS232 Serial control interface, Used for transfer data/commands 3. EARPHONE Earphone Signal Output. 4. COAX SPDIF‐audio Output (Digital sound signal interface ) 5. YPBPR(Y) For YPbPr signal input ( Connected to DVD, set ‐top –box etc. with YPbPr output device ). Y component signal input to this RCA Jack (G) 6.
14. HDMI 1 High Definition Multimedia Interface‐1 15. HDMI 2 High Definition Multimedia Interface‐2 16. POWER PC Turn ON/OFF the internal PC power (if installed) 17. RESET PC Internal PC reset, suspends all programs currently running, the PC system re‐starts NOTE: Functions related to PC will only work if internal PC is installed.
4.2 Remote Control Instruction Insert the Batteries 1 Remove the cover on the rear of the remote control 2 Insert two “AAA” batteries 3 Place the cover 4.3 Remote control range The range of remote control receiver as shown below: CAUTION RISK OF DAMAGE IF BATTERY IS REPLACED WITH AN INCORRECT TYPE DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
5 CONNECTION GUIDE For the safety of you and your unit, please do not connect any power source before the external device is installed. 5.1 External Computer and Touch Connecting (1) Connect a VGA cable (15pin) between the PC‐VGA Input and Output of external PC. Connect an audio cable between the PC and display. (2) Connect a USB cable between the external PC and USB terminal (3) Plug‐in the POWER cord and switch the display on.
5.2 AV Connection (1) Connect an AV cable between display and external device through the AV out. Yellow is Video, Red is Audio‐R, White is Audio‐L . (2) Plug‐in the POWER cord and turn ON the display. (3) Press main power switch located on the front of the display to IN position power on (4) Press INPUT to change source to AV. 5.3 Y‐Pb‐Pr INPUT (1). Connect the Y‐Pb‐Pr cable between the display and an external device. (2). Plug‐in the POWER cord and switch it on from the rear panel. (3).
5.4 HDMI1 / HDMI2 INPUT (1) Connect a HDMI cable from the display to an external device. (2).Plug‐in the POWER cord and switch it on from the rear panel. to turn the power on. (3) Press main power switch (4) From the external device select input source to HDMI. 5.5 COAXIAL CONNECTION (SPDIP AUDIO OUTPUT) (1) Connect a Coaxial cable from display to an external device. (2) Plug‐in the POWER cord and switch it on from the rear panel.
6 RS232C COMMUNICATION After connecting the central control system and unit, you can use RS232 control some of the function, such as power on/off or adjust the volume etc. 6.1 RS232C Baud speed: Bit number: Odd Parity: Stop bit: 9600bps 8 bit None 1 bit 6.
In the Protocol list (command list), ID=01 (0x01) is used.
7 INSIDE PC UNIT INSTALLATION/REPLACEMENT (OPTION) This PC unit （IWB PC‐02）is compatible with WB84U1D1 only, do not intend to attach this unit to the other models. Be sure Turn‐off the TWB Monitor before installation of inside PC. CAUTION 1. 2. 3. Power supply of inside PC and HDMI signal to IWB display are connected by internal 40‐pin connector. Before installation, check if something clogged at the connector‐pin area, if so, remove them and keep the connector clean.
At the right side of the IWB Monitor & at lower portion, Input terminals and switches are located. There are two switches, one for “PC Power” and the other “for PC reset”, they are the switches related to this Optional PC unit operation. The PC Power switch is a “cyclic type”, push‐ON, push‐OFF and PC Reset is push‐make contact type. Push Power PC button to switch ON PC Wait about 30 seconds after installing PC at back of the display, press POWER to turn on the Monitor and PC together.
8 OSD OPERATION 8.1 Instruction for main menu 8.1.1 Appearance 8.1.2 Operation of keys under main menu key Function Main Sub Menu Exit from Main menu Return to Main menu Exit Exit from Main menu Exit Menu Up ‐‐‐‐‐‐‐‐ Select previous Item, if current Item is the first one, then it. will skip to the last one Select next Item, if current Item is the last one, then it will skip to the first one Down Enter Sub Menu Right Change Sub Menu Adjust Item option or value; enter the next menu.
8.2 Function introduction of submenu 8.2.1 Picture submenu 8.2.1.1 Appearance 8.2.1.2 Function introduction Item Picture Mode Variable range Default Explanation Standard / Dynamic /Movie / User Standard Pressing button for Picture Mode Change Over.
Note: We set default setting as bellow, and you can change them to proper value for your product. Standard：Contrast = 50，Brightness = 50, Color = 50, Sharpness =50。 Dynamic：Contrast = 70，Brightness = 60, Color = 60, Sharpness =60。 Movie ：Contrast = 45，Brightness = 40, Color = 50, Sharpness = 50。 User：Contrast = 50，Brightness = 50, Color = 50, Sharpness = 50。 8.2.2 Audio submenu 8.2.2.1 Appearance 8.2.2.
8.2.3 Time submenu 8.2.3.1 Appearance 8.2.3.2 Function introduction Item Variable range Default Off/5Min/10Min/15Min/30Min Sleep Timer Off /45Min/60Min/90Min/120Min /180Min/240Min Pacific(UTC‐8)/ Alaska(UTC‐9)/ Hawaii(UTC‐10)/ Time Zone Pacific Eastern(UTC‐5)/ Central(UTC‐6)/ Mountain(UTC‐7) 8.2.4 Setup submenu 8.2.4.1 Appearance 22 Explanation Pressing Button to select one of Sleep Timer setting. Default value can be modified according to client's requirements.
8.2.4.2 Function introduction Item Menu Language Zoom Mode Noise Reduction Variable range Default Explanation English / French /Spanish Non VGA channel： Wide/Zoom/Cinema /Normal VGA channel ： Wide/Normal Off/Weak/Middle/ Strong English Wide Now there are only three kinds of language for OSD, if clients need more, we can add the language according to your needs.
8. 3 Hot Key Menu 8.3. 1 Info Key Note: 1、 If it is Display menu, then press INFO key to close the menu. It is also used to open Display menu 2、 After closing MENU and Source Input menu，Press INFO key, display menu will automatically pop up 3、 No operation for 3 seconds, then it is closed automatically 8.3.2 Picture Mode Press P‐Mode key, Picture Mode display menu opened. Key's functions： keys Function (P‐Mode) Picture Mode works only when there is signal.
Sound Mode (S‐Mode) MEMU EXIT ‐‐‐‐‐ Sound Mode key works only when there is signal. If it is S‐Mode menu, then change options of S‐Mode (order is same with that in main menu), or, it is used to open S‐Mode menu Exit from S‐Mode menu, open main menu Exit from S‐Mode menu No operation for 3 seconds, then exit from S‐Mode menu 8.3.4 Sleep Press Sleep key, Sleep timer menu appears on lower portion of screen.
Key's functions: keys Function Source If it is Source menu, Press for close Source Menu. Source Menu MEMU Exit from Source menu, open main menu EXIT RIGHT LEFT Exit from Source memu Used to change selection. ‐‐‐‐‐‐‐‐‐ UP Cursor moves to last ITEM DOWN Cursor moves to next ITEM OK/Enter or, Press it to open Used to change channel "Source Menu " Appear on screen, use "▲▼ / " to Navigate of each input source . Press "Enter" to make the input selection.
RIGHT If it is Volume menu, then volume will increase LEFT If it is Volume menu, the volume will decrease Note: No operation for 3 seconds, then Exit from Volume menu 8.3.8 MUTE menu Press Mute Key to open Mute Menu. Press once again， Mute Menu closed. Note: 1、Make sure MUTE menu exist with other menu, only MUTE key can close MUTE menu 2、When MUTE menu displays, if the option of CC Mode is On, then close MUTE menu.
9 USB Input mode 9.1 Introduction Select USB port from Input Source menu, then system in USB input status. In USB Input Mode , Only JPEG & M‐JPEG signal format can be support. The system automatically Identified file format , Only show the support file. 9.2 Appearance 9.2.1 Non Input Mode If No USB module inserted, Top and left of screen appear “ No device”. When USB module inserted, Top and left of screen will shown “ USB 2.0” etc. 9.2.
10 DISPLAY SIGNAL RESOLUTION FOR REFERENCE 1. Y‐Pb‐Pr (Y‐Cb‐Cr) Mode 2. VGA Mode 3.
11 RESOURCE DVD At accessory box , you could find a DVD disk. There are documents as below : 1) User’s Manu for WB55FiD1/WB65F1D1/WB70F1D1 (UM); 2) User Manual for WB84U1D1(UM) 3) WScribe Program for White Board (SW) 4) User’s Manu for White Board Program of WScribe (UM) 5) WScribe Program quick installation guide (QIG) 6) Driver Program for IWB PC‐01 & IWB PC‐02 Please follow the Quick Instruction Guide to install WScribe program and activate for White Board application.
When you need driver for PC， you can select IWB PC 01 Drivers for WB55、WBWB65、WB70。 For WB84，should select TWB PC‐02 Drivers。 12 TROUBLE SHOOTING Remote control: no function 1 .Check whether there is an object between remote control and IWB display. 2. Check whether the batteries polarity in remote control is correct. 3. Check whether the batteries are exhausted. The unit shuts down automatically 1. Check sleep function if activated. 2. Check whether there is a sudden power failure. 3.
No Touch Function 1. Check setup. 2. Check whether the touch pen is working properly. Remarks This IWB with 2‐ Touch USB, But it is option use with PC. It is not recommend both touch USB port connect with PC same time. Video not working properly No picture/No sound 1. Check POWER status. 2. Check the signal cable. 3. Check the PC source. Pixelization 1. Check the signal cable. 2. Check for other electronics signal interferences. Poor picture quality 1 .
www.westinghousedigital.
