WS-2100/4100 Manual
WS-2100/4100 Operating Manual CONTENTS About Our FWT 1. Before Using Your Terminal 1.1 Unpacking 1.2 Name and Function of Each Part 1.3 Sound & Tone 1.4 Safety Instructions 2. Installations 2.1 General Installation 2.2 Installation For the Data Service 2.3 Installing the Wall Bracket 3. Basic Functions 3.1 Power On 3.1.1 How to Operate with External Power 3.1.2 How to Operate with Built-in Battery 3.2 Power Off 3.3 Making a Call 3.3.1 General Method 3.3.2 Making a Call Using the Speed Dial Function 3.3.
WS-2100/4100 Operating Manual 4.2.2 Deleting Phone Numbers 4.3 Additional Function 4.3.1 Alarm Reminder 4.3.2 Handset Volume Control 4.3.3 Setting the Voice Privacy Function 4.3.4 Serial Baud Rate Setting 4.4 Lock 4.4.1 Outgoing Lock 4.4.2 Changing Lock Code (User’s Password) 4.4.3 Reset as Default 4. 5. Ma intenance S etup 4. 5. 1 C LIP S etting 4. 5. 2 Analog G3 F ax S etting 4. 5. 3 Default Data Rate S etting 4. 5. 4 Ringer F requenc y & C adenc e C ontrol 4. 5. 5 Dial Tone F requenc y C ontrol 4. 5.
WS-2100/4100 Operating Manual About Dowtel FWT (1) WS-2100/4100 both have a practical but elegant design. It can be used at office or home. WS-2100/4100 also offers many useful features and technological advantages. (2) WS-2100/4100 has Versatile Installation Options (3) WS-2100/4100 looks perfect on your desk in the office. It can also be installed on any wall in your office or home thanks to the wall-mount kit that comes with the unit.
WS-2100/4100 Operating Manual 1. Before Using Your Terminal This manual contains chapters on terminal introduction, installation method, basic directions, feature code and the technical standard, troubleshooting for potential problems. Please read through the contents of this manual carefully before using this product. [Note] If you have any questions or think that the product maybe defective, please contact the store where the unit was purchased. 1.
WS-2100/4100 Operating Manual SERIAL PORT ANTENNA POWER SWITCH RJ-11 JACK DC JACK SERVICE LED POWER LED BATTERY LED POWER LED LED lights in red indicates the external power is supplied. l BATTERY LED Indicates the status of backup battery. The terminal can be operated if the backup battery is connected, even though the external power supply is cut off. Please refer to the following table for the LED operation.
WS-2100/4100 Operating Manual l SERVICE LED Indicates the Signal Strength in your area. For better signal strength, please perform signal strength test to find the best operating location.
WS-2100/4100 Operating Manual 1.3 Sound & Tone 1.3.1 Power-Up Sound When the terminal’s power is turned on, a beep-sound is transmitted. 1.3.2 Dial Tone Indicates that call service is available. 1.3.3 Warning Tone The sound transmitted to the handset in the following cases. - In case the call is not available due to broken air link. - In case the dialing is delayed after the handset is picked up. - In case the terminal is not in the correct working mode. 1.3.
WS-2100/4100 Operating Manual 1.4 l Safety Instructions Basic safety precautions should always be followed to reduce the risk while using this unit. The WS-2100/4100 can be in service and remain in good condition for a long period of time if used properly, and given proper care. 1) To reduce the risk of electric shock, do not disassemble or alter the terminal. (Please contact the authorized service center for service or assistance) 2) Do not hold or make contact the antenna during a call.
WS-2100/4100 Operating Manual 2. Installations 2.1 General Installation Thank you for choosing this product. Before installing the terminal, please check whether the products package contains all the l parts and accessories are in the package. If there are items missing, please contact the store where the unit was purchased.
WS-2100/4100 Operating Manual 3) Connect the DC-JACK to the back panel of the terminal and insert the power jack to SMPS as shown below. 4) Connect the power plug of SMPS to a power outlet. 5) Turn power on by moving the switch to the right. l All 3 lamps (LED) light up initially. After a power-up melody plays through, a service lamp will turn green indicating call services is available. l l At this time Red Power light and Green Service light will remain on.
WS-2100/4100 Operating Manual [Notes] Malfunction Indicator In case of a malfunction, a service LED and a battery LED will light up in red and blink. In this case, please contact your service provider.
WS-2100/4100 Operating Manual 2.2 Installation For the Data Service. 1) PC – FWT c onnection < Connection of terminal to a PC for the Data communication > As shown above, connect a RS-232 cable to the Serial Port of the terminal and COM1 (or COM2) of PC. RS 232 cable is available from the service provider, or at any electronics store. 2.
WS-2100/4100 Operating Manual 3. Basic Functions 3.1 Power On The power for the terminal is supplied through SMPS and built-in battery. When the power is supplied through SMPS, the battery is automatically being re-charged and in case of a power loss, the power source is automatically changed from AC power to internal Battery. In addition, when the external power is restored, the power source is automatically back to AC power 3.1.1 How to Operate with External Power.
WS-2100/4100 Operating Manual 3.3.1 General Method 1) Pick up the handset and you will hear a dial tone (off-hook state). 2) If you hear the Dial Tone, then you can make a call. * If there is a warning tone at a 0.5 second interval, you can not make a call, check the LEDs, and contact your service provider. 3) Dial the telephone number and press the “*” button. 4) Start talking with the other party when the call is connected (Service LED is orange).
WS-2100/4100 Operating Manual 3.4 Receiving an Incoming Call 3.4.1 On-Hook State 1) The phone will ring when receiving an incoming call. 2) Pick up the handset, and start talking when connected to the other party (Service LED is Orange). 3) A call is terminated when you hang up the handset. 3.4.2 Off-Hook State 1) Even if the handset is off-hook state with dial tone or warning tone, you still can receive an incoming call.
WS-2100/4100 Operating Manual 3.5 How to Use Analog G3 Fax Terminals with the Analog G3 Fax Board can send and receive documents with Fax machine. Fax Board is an optional item. To use Fax function, Fax machine should be connected with terminal. 3.5.1 To Send a Document by Fax Pick up the Fax handset and make sure there is a dial tone then press *00 and then dial the number you want to send the Fax on Fax machine and follow the instructions of the Fax machine connected to the terminal. 3.5.
WS-2100/4100 Operating Manual 1) Setting Data Services Receiving Mode using a regular phone set. You can set the unit to the Data Service Receiving Mode by using a regular phone set connected to the terminal. ① Pick up the phone handset and press ###001. The unit has been programmed to the PC Fax Receive, One Time Mode. ② Pick up the phone handset and press ###002. The unit has been programmed to operate in the PC Fax Receive Always Mode. ③ Pick up the phone handset and press ###003.
4. Supplementary Functions 4.1 Call Functions 4.1.1 Speed Dial This terminal will store up to 99 phone numbers using 2 digit addresses (01-99). The stored number in the Phonebook allows a call to be placed by pressing the two digit address. This terminal has the ability to search and edit numbers stored in the Phonebook, and the methods for storing, searching and editing a stored phone number are explained in section 4.2. 4.1.1.
WS-2100/4100 Operating Manual 4.1.2 Hot Line function 1) This function is used to make an automatic, quick call to a designated number without dialing. Just pick up the handset, then a call will be made. 2) The Hot Line number should be registered at address 99 in the Phone book. Hotline operates in 2 modes; *Timed Hot Line; The call will be made in delayed manner between 4-8 seconds (sending waiting time), depending on your default value, after you pick up the handset. Original default value is 6 seconds.
WS-2100/4100 Operating Manual 4.2 Phone Book 4.2.1 Storing Phone Numbers Press; #0*100 à 2 à 1 à address (2 digits) à phone number à * ① Pick up the telephone handset and enter the code as shown below. < #0*100 à 2 à 1 > enter the 2 digit address you would like to store the phone number. Suppose the address is <4>, press [04] ② Enter the phone numbers to be saved digit by digit . ③ When you press <*> button (saving), you will hear a indicating the number has been successfully stored.
WS-2100/4100 Operating Manual 4.3 Additional Functions 4.3.1 Alarm Reminder The terminal sends a reminder to the user by ringing at a specified time. The time is set using a 24 hours format. 2 specific settings are possible. The activates the alarm only once while the it activates the alarm everyday at the same specified time. The time and function setting are shown below.
WS-2100/4100 Operating Manual 4.3.2 Handset Volume Control This function is used to control the volume of handset. The handset volume can be set at 5 different levels and the default setting is Level 3. 2 methods for changing this setting are listed below. 1) Change using the menu code (Idle State) ① Enter #0*100à3à2 ② Select and press a desired level: #1 (Level 1: minimum) , #2(Level 2) , … , #5 (Level 5: maximum). ③ Press <*> button to save the setting.
WS-2100/4100 Operating Manual 4.3.3 Setting the Voice Privacy Function This terminal is equipped with voice privacy function to prevent illegal tapping. There are two detailed settings available, for regular level voice privacy mode and for reinforced voice privacy mode. The Voice Privacy function can be enabled using the method shown below. 1) While In idle state ① Enter #0*100à3à3 sequentially. ② Press <1> button for < Enhanced > mode and <2> button for < Standard > mode.
WS-2100/4100 Operating Manual 4.4.1 Outgoing Lock The Outgoing Lock function is used to block other people from using the terminal. If you make a call while this function is on, the terminal generates an error sound indicates that making a call is not possible. This function only prevents outgoing calls. Receiving a call is still possible while the Outgoing Lock function is turned on. To use the phone, you need to unlock the phone by entering your password. The Default setting is . 4.
WS-2100/4100 Operating Manual ◆ How to reset to the default setting. ① Press #0*100à4 ② Enter your password and press <4>. ③ If you press <*> button, all the major functions listed below are reset to the following values. #0*100 à4àpasswordà 4 à * : How to do the default setting [Note] Reset items and their status are as shown in the table below.
WS-2100/4100 Operating Manual 4.5 Maintenance Setup 4.5.1 CLIP Setting Since this terminal does not have an LCD, incoming calls are displayed on the LCD of the specific module or telephone connected to the terminal. Consequently, a communication method between the terminal and the module need to be set in one of the following two available modes: DTMF mode and FSK mode.
WS-2100/4100 Operating Manual 4.5.2 Analog G3 Fax Setting 1) WS-2100/4100 support Analog G3 Fax Service using the standards below: - IS-99/IS-707.4 based PC Fax standard - IS-707A.7 Analog G3 Fax standard [Note] In case of IS-99/IS-707.4 based PC Fax standard, a service provider will require the user to decide the fax receiving method in advance: a PC fax program or Analog G3 fax. (The fax program or the Analog G3 Fax becomes a Default Fax Receiver) 2) In case of IS-99/IS-707.
WS-2100/4100 Operating Manual 4.5.3 Default Data Rate setting This terminal supports the standard data rates listed below. - IS-99 Rate Set 1 - IS-99 Rate Set 2 - IS-707.4 Rate Set 1 - IS-707.4 Rate Set 2 The following is the Default Rate setting for Data Signal access. 1) Setting IS-99 Rate Set 1 (9.6K) ① Enter #0*100à8àMaintenance Codeà3 in order. ② Press <1> button. ③ Press <*> button to save the setting. #0*100à8àMaintenance Codeà3à1 à * 2) Setting IS-99 Rate Set 2 (14.
WS-2100/4100 Operating Manual The Default setting is 20Hz, 1 Sec. On – 2 Sec. Off. Listed below are the ringer frequency selection and Cadence settings. ① Enter #0*100à8àMaintenance Codeà4 ② Select the ringer frequency Press the desired number between No. 1(16Hz), No. 2(20Hz), No. 3(25Hz) ③ Select Cadence No 1 (1 sec On – 2 sec Off), No 2 (0.4 sec On – 0.2 sec Off - 0.4 sec On – 2 sec Off), No 3 (1 sec On – 4.5 sec Off), No 4 (1 sec On – 4 sec Off), No 5 (0.25 sec On – 0.25 sec Off - 0.25 sec On – 1.
WS-2100/4100 Operating Manual 4.5.5 Dial Tone Frequency Control This function is used to select the frequency of the Dial Tone transmitted through the handset. The default setting is 350 + 440Hz. 1) Menu Code Method ① Enter #0*100à8àMaintenance Codeà5 ② Press the number of your choice between No 1(350+440Hz), No 2(400Hz), No 3(425Hz), No4(450Hz) ③ Press <*> button #0*100 à8àMaintenance Codeà5à1～4à * 4.5.6 Waiting tone Frequency control The default setting is 350 + 440Hz.
WS-2100/4100 Operating Manual 4.5.8 Auto Dial Send Time Control Auto Dial Send is a function that makes a call to the dialed number after specified time lapses. Terminal starts making a call, specified seconds after user finishes dialing the number. Auto dial send time is adjustable from 4 seconds to 8 seconds and default setting is 6 sec. 2 setting methods are provided below.
WS-2100/4100 Operating Manual [Note] As the mal-operation with this terminal while referring to this manual may cause the terminal impossible to acquire the system, it should be carefully operated and advance consult with a terminal supplier is required.
WS-2100/4100 Operating Manual 4.6 System Parameter Setu p Every point on the System Parameter setup is much important enough to determine the possibility for this terminal ’ s service. In particular, because the terminal (WS does not have the display module, there is no way to check the parameter setu - 2100/4100) p procedure. Therefore, in case of changing parameters, a careful reference on this chapter is required.
WS-2100/4100 Operating Manual #0*901à2àDirectory No.à * If a user wants to delete the saved Directory Number, he or she can skip above procedure ② and just press <*>. The procedure is as below. #0*901à2àDirectory No.à * [Note] Mobile Directory Number is allowed up to 15 digits. 4. 6.3 Country Code (MCC) Input ① Press #0*901à3 in order ② E nter 3 dig its of MC C ③ Press <*> button to save #0*901à3àMC C (3 digits) à * 4. 6.
WS-2100/4100 Operating Manual 4. 6.7 SID/NID Input & Delete [Note] If the terminal in use now is WS - 2100, this menu appears only if PRL function in 4 .5.10 PRL Select is set to Disable.
WS-2100/4100 Operating Manual 1 : C DMA Primary A C hannel 2 : C DMA Primary B C hannel 3 : C DMA S econdary A C hannel 4 : C DMA S econdary B C hannel ③ Input c ha nnels ④ Press <*> button to finish #0*901à9à1~ 4àChannel à * 2) C hannel Delete ① Press #0*901à9 in order ② S elec t 1~ 4 to delete c hannel 1 : C DMA Primary A C hannel 2 : C DMA Primary B C hannel 3 : C DMA S econdary A C hannel 4 : C DMA S econdary B C hannel ③ Press <*> button to finish #0*901à9à1~ 4à * 37
WS-2100/4100 Operating Manual APPENDIX 1.
WS-2100/4100 Operating Manual #0*100à8à Maintenanc e C ode à1à1à* : D T MF mode on #0*100à8à Maintenanc e C ode à1à2à1à* : F S K T ype2 mode on CLIP Setting #0*100à8à Maintenanc e C ode à1à2à2à* : F S K T ype1 mode on #0*100à8à Maintenanc e C ode à1à3à* : C L IP mode off #0*100 à 8 à Maintenance Code à 2 à 1 à 1 / 2 à * Analog G3 Standard Setting Fax IS-99/707.4 Fax method PC 2: Analog G3 receiving default IS-707A.7 method (1: RS 1 (IS99), 2: RS 2 (IS99), 3: RS 1 (IS707.4), 2: Rate Set 2 (IS707.
WS-2100/4100 Operating Manual Channel(WS2000 Only) (input) #0*901 à 9 à Channel select (1~4) à Channel input à * (delete) #0*901 à 9 à Channel select (1~4) à * 40
WS-2100/4100 Operating Manual 2. Technical Specification 2.1 800MHz bandwidth Air Interface Common air interface standard → IS -95A/B & IS-95C(CDMA2000) FREQUENCY → TX: RX: 824 – 849MHz 869 – 894MHz TX Max. Output Power → 200mW ~ 300mW RX Sensitivity → - 104dBm below Vocoder → 8K/13K QCELP, 8K EVRC Channel Bandwidth → CDMA 1.25Mhz RX Conducted Spurious → TX BAND: RX BAND: -61dBm below -81dBm below MOD/DEMOD → O QPSK/QPSK Frequency Accuracy → Fo± 300Hz Battery Back-Up Type → Ni-Cd Capacity → 6V @ 1.
WS-2100/4100 Operating Manual 2.2 1.9GHz Bandwidth Air Interface Common air interface standard →J-STD-008, IS -95B & IS-95C FREQUENCY → TX: 1850-4100MHz RX: 1930-1990MHz TX Max. Output Power → 200mW ~ 300mW RX Sensitivity → - 104dBm below Vocoder → 8K/13K QCELP, 8K EVRC Channel Bandwidth → CDMA 1.25Mhz RX Conducted Spurious → TX BAND: RX BAND: -61dBm below -81dBm below MOD/DEMOD → O QPSK/QPSK Frequency Accuracy → Fo± 150Hz Battery Back-Up Type → Ni-Cd Capacity → 6V @ 1.
WS-2100/4100 Operating Manual In the event of a product malfunction, please check the list below for a possible solution before contacting your local service provider. In Case… ▶ No sound after picking up the phone Try This… ☞ Check if the terminal Power LED or Battery LED is on. If the power is off, check if the SMPS power plug is properly connected. ☞ Check if RJ-11 Jack is properly connected.
WS-2100/4100 Operating Manual Safety Information 1 . SAFETY INFORMATION FOR FIXED WIRELESS TERMINALS .POTE NTIALLY EXPLOSIVE AT MOSPHERES Turn your phone OFF when in any area with a potentially explosive atmosphere and obey all signs and instructions. Sparks in such areas could cauls e an explosion or fire resulting in bodily injury or even death. . INTERFERENCE TO MEDICAL DIVICES Certain electronic equipment may be shielded against RF signal from you wireless phone.
WS-2100/4100 Operating Manual SAR INFORMATION THIS MODEL PHONE MEETS THE GOVERNMENT ’ S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES. Your wireless phone is a radio transmitter and receiver. It is designed and anufactured not to exceed the emission limits for exposure to radio frequency (RF)energy set by the Federal Communications Commission of the U.S.Government.These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population.
WS-2100/4100 Operating Manual FCC RF EXPOSURE INFORMATION In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96-326 adopted an updated safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies.
WS-2100/4100 Operating Manual FCC Compliance Information This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received. Including interference that may cause undesired operation. Information to User This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
