MODEL 4212, 4212T 10" VARIABLE SPEED DRILL PRESS Instruction Manual NEED HELP? CONTACT US! Have product questions? Need technical support? Please feel free to contact us: 1-800-232-1195 (M-F 8AM-5PM CST) TECHSUPPORT@WENPRODUCTS.COM IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance.
CONTENTS WELCOME 3 Introduction...................................................................................................... 3 Specifications.................................................................................................... 3 SAFETY 4 General Safety Rules......................................................................................... 4 Drill Press Safety Warnings.............................................................................. 6 Electrical Information...
INTRODUCTION Thanks for purchasing the WEN Drill Press. We know you are excited to put your tool to work, but first, please take a moment to read through the manual. Safe operation of this tool requires that you read and understand this operator’s manual and all the labels affixed to the tool. This manual provides information regarding potential safety concerns, as well as helpful assembly and operating instructions for your tool. Indicates danger, warning, or caution.
GENERAL SAFETY RULES WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Safety is a combination of common sense, staying alert and knowing how your item works. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. SAVE THESE SAFETY INSTRUCTIONS. WORK AREA SAFETY 1. Keep work area clean and well lit.
GENERAL SAFETY RULES WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Safety is a combination of common sense, staying alert and knowing how your item works. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. SAVE THESE SAFETY INSTRUCTIONS. 7.
DRILL PRESS SAFETY WARNINGS WARNING: Do not let comfort or familiarity with the product replace strict adherence to product safety rules. Failure to follow the safety instructions may result in serious personal injury. 1. TOOL PURPOSE. This drill press is designed to drill through metal wood, plastic, and tiles. Drilling through other materials could result in fire, injury, or damage to the workpiece.
DRILLRULES PRESS FOR SAFETY SPECIFIC THEWARNINGS DRILL PRESS 12. DRILLING THE WORKPIECE. • Allow spindle to reach full speed before drilling the workpiece. • Never start the machine with the drill bit pressed against the workpiece. • Adjust the table or depth stop to avoid drilling into the table. • Set the drill press to the speed that is appropriate for the material being drilled. 13. Do not touch moving pieces. Keep hands away from the drill bit during operation.
ELECTRICAL INFORMATION GROUNDING INSTRUCTIONS IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides the path of least resistance for an electric current and reduces the risk of electric shock. This tool is equipped with an electric cord that has an equipment grounding conductor and a grounding plug. The plug MUST be plugged into a matching outlet that is properly installed and grounded in accordance with ALL local codes and ordinances. DO NOT MODIFY THE PLUG PROVIDED.
KNOW YOUR DRILL PRESS TOOL PURPOSE Drill presses are mainly used to drill clean, precise cylindrical holes into workpieces or enlarge existing holes. You may also find other uses for your drill press such as reaming, countersinking, counterboring, tapping, etc. Refer to the diagram below and on page 10 to become familiarized with the parts and controls of your drill press. 13 5 6 1 12 7 8 9 3 2 11 10 4 Fig. 2 1. 2. 3. 4. 5.
ASSEMBLY & ADJUSTMENTS UNPACKING With the help of a friend or trustworthy foe, carefully remove the drill press from the packaging. Make sure to take out all contents and accessories. Do not discard the packaging until the drill press is completely assembled. Before using the drill press, you must assemble the unit using the instructions in this section. Check your packing list against the diagram below.
ASSEMBLY & ADJUSTMENTS WARNING: Do not plug in or turn on the tool until it is fully assembled according on the instructions. Failure to follow the safety instructions may result in serious personal injury. ATTACHING COLUMN TO BASE (FIG. 3) 1 3 1. Place the column tube (Fig. 3 - 1) on the base (Fig. 3 - 2), aligning the column support holes to the base holes. 2. Install a socket head cap screw (Fig. 3 - 3) in each column support hole and tighten screws using the included 5mm hex wrench.
ASSEMBLY & ADJUSTMENTS DRILL PRESS HEAD TO COLUMN (FIG. 7) 1 CAUTION: The drill press head is heavy. To avoid injury, two people should lift it into position. 3 1. Carefully lift the drill press head assembly (Fig. 7 - 1) and position it over the column (Fig. 7 - 2). 3 2 2. Place the mounting opening on the drill press head over the top of the column. Make sure the drill press head is seated properly on the column. Fig. 7 3.
ASSEMBLY & ADJUSTMENTS INSTALL THE CHUCK (FIG. 11) 1. Inspect and clean the taper hole in the chuck and the spindle. Remove all grease, coatings, and particles from the chuck and chuck arbor surfaces with a clean cloth. 2. Open the chuck jaws by manually turning the chuck barrel clockwise. Make sure the jaws are completely recessed inside the chuck. Spindle Chuck 3.
ASSEMBLY & ADJUSTMENTS TILT THE TABLE (FIG. 13) 1. Loosen the bevel lock bolt (under table) with a suitable socket or wrench (not included). 1 2. Tilt the table to the desired angle, using the bevel scale (1) as a basic guide. 3. Re-tighten the bevel lock bolt. Fig. 13 4. To return the table to its original horizontal position, loosen the bevel lock bolt. 5. Realign the table to the 0° setting on the bevel scale. 6. Tighten the bevel lock bolt with the wrench.
ASSEMBLY & ADJUSTMENTS SQUARING THE TABLE TO THE DRILL BIT (FIG. 14) 1. Insert a 3" drill bit (Fig. 14-1) into the chuck (Fig. 14-2) and tighten. 2. Raise and lock the table (Fig. 14 - 3) about 1" from the end of the drill bit. 3. Place a combination square (Fig. 14 - 4) on the table as shown. The drill bit should be parallel to the straight edge of the square. 2 1 4 3 5 Fig. 14 4. If an adjustment is needed, loosen the bevel lock (Fig. 14 - 5) with a wrench. 5.
ASSEMBLY & ADJUSTMENTS SPINDLE RETURN SPRING (FIG. 16A) The spindle is equipped with an auto-return mechanism. The main components are a spring and a notched housing. The spring was properly adjusted at the factory and should not be readjusted unless absolutely necessary. 2 3 4 1 1. Unplug the drill press. Fig. 16A 2. Place a screwdriver into the loop (Fig. 16A - 1) to hold the spring in place. 3. Loosen the two housing nuts (Fig. 16A - 3) approximately 1/4" (6 mm).
ASSEMBLY & ADJUSTMENTS DRILL PRESS ON/OFF SWITCH (FIG. 17) 1. To turn the drill press ON, insert the yellow safety key (Fig. 17-1) into the switch housing (Fig. 17 - 2). As a safety feature, the switch cannot be turned ON without the safety key. 1 2 2. Turn the switch to the ON position. 3. To turn the drill press OFF, flip the switch downward. 4. To lock the switch in the OFF position, remove the safety key (Fig. 17 - 1) from the switch. Store the safety key in a safe place. Fig.
OPERATION LASER LINE ON/OFF SWITCHES (FIG. 18) The laser switch (Fig. 18 - 1) is located on the left hand side of the drill press. 2 1 1. Pull the tab located below the laser switch and lift up the laser switch cover (Fig. 18 - 2). 2. Install two AA batteries into the battery slots and close the switch cover. POSITION THE TABLE AND WORKPIECE Always place a piece of backup material (wood, plywood, etc.) on the table underneath the workpiece.
OPERATION ADJUST THE DRILLING DEPTH (FIG. 19) 1. Loosen the depth scale knob and turn the depth scale ring to the desired depth. 2. Lock the scale ring in place by tightening the depth knob. This will stop the bit once it reaches a certain depth. DRILLING SPEEDS Fig. 20 NOTE: View Drill Bit Size Recommendations on page 20 for general guidelines.
OPERATION FEEDING THE DRILL BIT • Pull down on the feed handles with only enough force to allow the drill bit to cut. • Feeding too rapidly might stall motor, cause the belt to slip, damage the workpiece, or break the drill bit. • Feeding too slowly will cause the drill bit to heat up and burn the workpiece. MECHANICAL VARIABLE SPEED (FIG. 21) This is a mechanical variable speed drill press. To increase or decrease the speed when operating, raise or lower the speed handle (Fig. 21 - 1).
MAINTENANCE WARNING: To avoid accidents, turn OFF and unplug the tool from the electrical outlet before cleaning, adjusting, or performing any maintenance or lubrication work. WARNING: Any attempt to repair or replace electrical parts on this tool may be hazardous. Servicing of the tool must be performed by a qualified technician. When servicing, use only identical WEN replacement parts. Use of other parts may be hazardous or induce product failure.
TROUBLESHOOTING GUIDE WARNING: Stop using the tool immediately if any of the following problems occur. Repairs and replacements should only be performed by an authorized technician. For any questions, please contact our customer service at (800) 232-1195, M-F 8-5 CST or email us at techsupport@wenproducts.com.
TROUBLESHOOTING GUIDE WARNING: Stop using the tool immediately if any of the following problems occur. Repairs and replacements should only be performed by an authorized technician. For any questions, please contact our customer service at (800) 232-1195, M-F 8-5 CST or email us at techsupport@wenproducts.com.
EXPLODED VIEW & PARTS LIST 24
EXPLODED VIEW & PARTS LIST No. 1 2 3 4 5 Part No.
EXPLODED VIEW & PARTS LIST 26 No. 78 Part No.
WARRANTY STATEMENT WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of two (2) years from date of purchase.
THANKS FOR REMEMBERING V. 2022.01.