PRO 100 Smart Projector User Manual
User Notice Thank you for choosing WEMAX PRO 100. For your security and interests, please read this manual carefully before using the product. If without properly operation shown in the user manual, personal injuries and other damages are caused, we will not take the corresponding responsibilities. Illustrations of product, accessories, and user interface in the user manual are for reference purposes only. Actual product and functions may vary due to product enhancements.
Product Overview Exterior Lens Speaker Mesh TOF Module Camera Ports Speaker Speaker Heat Dissipation Vents Right Air Inlet Rubber Feet Power Button 1/4'' Female Threaded Tripod Mount (length 6mm) Caution : - Do not place any flammable objects near the heat dissipation vent. - Do not place any objects near the vents, as this may cause heat to build up inside the projector. - Do not look directly into the lens so as to avoid eye damage as this projector emits strong light during use.
Suspended Ceiling Installation Suspended ceiling installation is one of the installation methods that you hang the projector in an overhead location, for example, on a high ceiling, through a ceiling mount. A projector supporting suspended ceiling installation has threaded holes on the bottom, you can install the project on the mount by attaching the screws into the holes. The installation steps are as follows: 1. Install the mount.
Connection Ports ① ③ 5 7 1 HDMI 2 - HDMI input port 2 2 HDMI 1(ARC) - HDMI input port 1 - (ARC) Audio return channel port 3 USB 2.0 - Supports USB 2.0 communication protocol ② ④ 4 USB 2.0 - Supports USB 2.
Remote Control Power: Xifo!uif!qspkfdups!jt!pgg-!tipsu!qsftt! up!uvso!po/ Xifo!uif!qspkfdups!jt!po-!tipsu!qsftt! up!pqfo!uif!nfov-!mpoh!qsftt!up!uvso! pgg!uif!qspkfdups/ Voice: Mpoh!qsftt!uif!wpjdf!dpouspm!cvuupo! boe!ubmljoh!dmptf!up!uif!sfnpuf!dpouspm/ Launch Board: Bddftt!uif!mbvodi!cpbse! joufsgbdf/ Navigation Pad: Npwf!up!vq-!epxo-!mfgu-!ps! sjhiu-!uifo!qsftt!uif!njeemf! up!dpogjsn/ Home: Sfuvso!up!ipnf!tdsffo/ Return: Sfuvso!up!uif!qsfwjpvt!nfov/ Menu: Volume: Tipsu!qsftt!up!bddftt!uif!qspdftt! n
Quick Start Guide1 Note: The user interface will be updated from time to 1 Power on/off Plug in the power adapter, then press the power button to turn on. When the projector is on, press the power button on the top to open the power options, then press the power button again to shut down. 2 Pairing the Remote After installing the batteries in the remote control, press the OK button to start pairing.
Auto Focus is enabled by default, moving the projector will automatically trigger the screen to focus. To turn it off, go to 【Settings】 > Image > Auto Focus.
5 Auto Obstacle Avoidance & Auto Screen Alignment Auto Obstacle Avoidance & Auto Screen Alignment are enabled by default. If the projector is moved, it will automatically detect objects in the projection area and scale the image to avoid it. If screen is used, the projector will match the projected image with your screen automatically during auto screen adjusting process.
7 System Press 【Launch Board】 button on the remote control or select 【Launch Board】 in the shortcut menu bar at the top of the homepage to access the launch board interface. All installed Apps can be found on this page. 08:08 Settings File Manager Cast Projection Bluetooth Speaker Inputs Select 【Settings】 in the shortcut menu bar at the bottom of the homepage to enter the 【Common Menu】 page. All frequently used functions and software upgrade notifications will be displayed on this page.
8 Intellectual Temperature Control The LED light source and motherboard temperature are monitored by the projector's system, and the fan's speed is automatically adjusted based on the temperature detected by the sensor. - The projector has two brightness modes to choose from when operating at a normal temperature. To adjust the projector's brightness level, go to Settings > Image > Brightness Mode.
Daily Maintenance 1 Heat Dissipation Outlet Note: Avoid touching the heat dissipation vent on the rear, as it can become very hot Note: Do not place any objects within 20 cm of the projector's air vents, as this will affect the heat dissipation effect. 2 Cleaning Be sure to clean the projector casing and lens regularly using the included cleaning cloth or a specialized cleaning cloth. Do not use any abrasive cleaners, solvents or other rough chemicals.
Troubleshooting Fault Solution No projected image Restart the projector. If the problem remains, try tabbing the reset hole to reset the projector. System crashes Restart the projector. If the problem remains, try tabbing the reset hole to reset the projector. Screen display error Restart the projector. If the problem remains, try tabbing the reset hole to reset the projector.
说明书制作说明 1. 成品尺寸:80x140mm 2. 材质:105g哑粉 3. 印刷颜色:PANTONE Cool Gray 11 C 单色 4. 装订方式:风琴折 版本 A B C 说明书版本变更 说明 新版发行 遥控器更新 更新UI,增加FengOS系统介绍 时间 2020.02.25 2020.04.20 2020.08.
Product Certifications This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
Product Certifications Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. For DTS patents, see http://patents.dts.com. Manufactured under license from DTS, Inc. (for companies headquartered in the U.S./Japan/Taiwan) or under license from DTS Licensing Limited (for all other companies). DTS, DTS-HD Master Audio, DTS-HD, Virtual:X, and the DTS-HD logo are registered trademarks or trademarks of DTS, Inc.