Users Manual CSH-07334 IC Card/IC Tag Reader/Writer CSH-07334
US Regulations This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Trademarks Microsoft、MS are the U.S. Microsoft Corporation's registered trade-marks or the trademarks in the U.S. or other countries. Windows XP、Windows 2000 are the U.S. Microsoft Corporation's registered trade-marks or the trademarks in the U.S. or other countries. my-d is the Infineon Technologies Inc.'s registered trade-marks or the trademarks. I・CODE is the NXP Semiconductors Inc.'s registered trade-marks or the trademarks. Tag-it is the Texas Instruments Inc.
SAFETY PRECAUTIONS ・ Be sure to read these precautions before using this product in order to insure safe operation of the equipment. ・ Keep this User's Manual on hand for future reference whenever you may need it. Strict observance of these warning and caution indications are MUST for preventing accidents which could result in bodily injury and substantial property damage. Make sure you fully understand all definitions of these terms and related symbols given below, before you proceed to the text itself.
Observe strictly Warning Observe the display of the danger that the manufacturer of the personal com-puter and peripherals used is directing and warning and attention strictly when you use the product. Do not attempt disassemble or modify the products, which may result in injury, electric shock, excessive heat, fire. Do not use this product in a place in danger of catching fire and exploding. Do not use this product near the electric device which processes highly precise control and a weak signal.
Warning Do not place or use the products in the hot, high humid or dusty places such as a fire side, a stove side, under the burning sun, etc. Doing so could cause a fire, burn, bodily injury, or serious damage to property. Do not place or use products in high humid or dusty areas. Doing so could cause a fire, burn, bodily injury, or serious damage to property. Do not put in in water, and sprinkle water by strong power. Do not give the high impact.
Contents Bundled items .................................................. Contents ....................................................... Introduction................................................... Notational Information ......................................... 1 iv v vi vi HARDWARE.......................................................1-1 1-1 P ART NAMES AND FUNCTIONS ...............................................................1-2 1-2 S PECIFICATION OF CSH-07334...............................
Introduction Thank you for purchasing our IC tag/IC card reader writer “CSH-07334”. CSH-07334 is a reader writer compatible with IC/cards/IC tags of the following makers. ・ Infineon Technologies “my-d” ・ Texas Instruments “Tag-it HF-I” ・ NXP Semiconductors “I・CODE1” “I・ CODE SLI” ・ Fujitsu “FerVIDfamily” It is a guidance type read/write communication equipment (model designation acquired) that can read multiple tags collectively (anti-collision function).
Chapter 1 1 Hardware
Chapter 1 Hardware 1-1 Part names and functions ① PW LED This lights up in red when the power is turned on. ② R/W LED This lights up in green when the equipment reads and writes a card (tag). ③ RF LED This lights up in yellow when the radio wave is outputted. ④ USB connector Connect the attached USB cable with PC. ⑤ Buzzer sound hole ⑥ Product nameplate Model Serial Number IC Card / IC Tag Reader Writer C S H-07334 SER No.
1-2 Specification of CSH-07334 1-2 Specification of CSH-07334 1-2-1 Environmental condition Item Specification Working temperature 0 to 40ºC (There should be no rapid temperature change and condensing.) Working humidity 20 to 80% Storage temperature -10 to 50ºC (There should be no rapid temperature change and condensing.) Storage humidity 1-2-2 10 to 90% Hardware specification Indicator LED PW LED Red Lights up when the power is turned on.
Chapter 1 Hardware 1-2-3 Appearance specification 1-2-4 Operating environment ●Compatible OS (Japanese version) ・ Windows XP ・ Windows 2000 ●Environment ・ CD-ROM drive Required to install the driver ・ USB connector One required to connect this product (A type) 1-2-5 Communication interface specification ・ Connector: USB miniB type connector ・ Terminal function: Compliant with USB Specification Rev1.
1-3 How to hold the IC card/IC tag 1-3 How to hold the IC card/IC tag This equipment accesses the IC card/IC tag in the range shown by the shaded area in the figure below. Be careful not to let it go beyond the range during access. Communication range: About 5cm from the center of the unit when the tag and the unit are held horizontally (for the credit card size) ■To use a small tag Use it within the following range. If the tag used is extremely small, reading it may fail.
Chapter 1 Hardware ■To use CSH-07334 laid side-by-side To use CSH-07334 laid side-by-side, isolate CSH-07334 by about 10cm. If the distance is too close, the communication performance may be affected.
Chapter 2 2 Software
Chapter 2 Software 2-1 How to install the driver software 2-1-1 Installing the driver software Install the driver software of CSH-07334 according to the following procedure. Install the driver software before connecting CSH-07334. ① Turn on the power of your PC and start Windows. Log in with a system administrator authorization. ② Insert the CD-ROM bundled with the product into the CD-ROM drive. ③ Click [My computer]→[CD-ROM drive]→[CSH-07334]→[drivers]→[PreInstaller.exe].
2-1 How to install the driver software ⑥ When the following screen appears, click [OK] and take out the CD-ROM. ⑦ Use the attached cable to connect CSH-07334 to your PC. If you use Windows2000, the installation operation is complete. If you use WindowsXP, proceed to “2-1-2 Connecting to Windows XP” (P.2-3). 2-1-2 Connecting to Windows XP If you use Windodws XP, carry out the following setting after installing the driver software (P.2-2).
Chapter 2 Software ③ The following screen appears during installation. Microsoft performs a qualification procedure for PC units and peripheral devices in an organization called WHQL. CSH-07334 has not been qualified as of February, 2006. Click [Continue] here to continue installation of the driver of CSH-07334. ④ When the following screen appears, the driver of CSH-07334 has been installed. Click [Complete]. After this, installation of the driver starts again.
2-2 Checking after connection 2-2 Checking after connection After installing the driver software, check if CSH-07334 is correctly connected. ① Right-click [My Computer] and select [Property] or [Control]. ② Double-click [Port (COM and LPT)] on the device manager screen (“Device manager” tab) and check that CSH-07334 is displayed. The COM number varies depending on the environment of your PC. ③ When you have finished checking, close the screen.
Chapter 2 Software 2-3 Uninstalling the driver software Uninstall the driver according to the following procedure. ① Select [Adding and deleting programs] from [Control panel]. ② Select [e-front CSH-07334 Controller] from the list and press [Change and delete] button to delete it. ・ Keep CSH-07334 connected to your PC to uninstall the driver. ・ Remove CSH-07334 from your PC after you have uninstalled the driver.
Chapter 3 3 FAQ (Frequently asked questions)
Chapter 3 FAQ 3-1 FAQ (Frequently asked questions) This section describes frequently asked questions, troubles, items requiring checking to resolve those troubles and reference pages on this manual. Make an inquiry to our Website for those troubles you can not resolve here. Q:I connected CSH-07334 before installing the driver. A:Install the driver manually. The driver software is included in the [Drivers] folder of the bundled CD-ROM. See the folder to install the driver.
IC Card / IC Tag Reader / Writer CSH-07334 Users Manual September, 2007 Manual Rev.1.0 Copyright ©2007 Welcat Inc. http://www.welcat.co.jp/ info@welcat.co.