Operating Instructions 3D Eyewear Model No. TY-ER3D4MA This product cannot be used as sunglasses.
Viewing 3D images You can enjoy viewing 3D images with contents or programmes corresponding to the 3D effect by wearing the 3D Eyewear (supplied). “Standard accessories” (p. 6) This TV supports [Frame Sequential] 1, [Side by Side] 2 and [Top and Bottom] 3 3D formats. 1: The 3D format that the images for the left and right eyes are recorded with the high definition quality and alternately played back. 2, 3: Other available 3D formats Ɣ How to use the 3D Eyewear (p. 31) Ɣ How to view the 3D images (p.
Viewing 3D Content Ɣ Do not use the 3D Eyewear if you have a history of over-sensitivity to light, heart problems, or have any other existing medical conditions. Ɣ Please stop using the 3D Eyewear immediately, if you feel tired, are not feeling well or experience any other uncomfortable sensation. When you set the effect by using [3D Adjustment], take into account that the vision of 3D images varies among different individuals. Ɣ Take an appropriate break after viewing a 3D movie.
Part names and functions Ɣ 3D Eyewear can be worn over vision correction glasses. Power switch Slide the tab to the “ON” / “OFF” position to switch the power on/off. Each time slide the tab to the “MODE” position to change the mode between 3D and 2D (view a 3D image in 2D). Registration (p. 32) Indicator lamp Lights or flashes during use to show the status. Pull Battery cover Ɣ When using for the first time, remove the insulating sheet. Pull the insulating sheet.
Registration First registration Perform the first registration when the 3D Eyewear is used for the first time. 1 Turn on the TV. 2 Slide the power switch from “OFF” to “ON”. The 3D Eyewear will power on and start registration. Place the 3D Eyewear within 50 cm from the TV while registration in progress. 3 The green LED lights on the 3D Eyewear for 3 seconds when the registration is successfully completed.
Replacing the battery When the battery is running low, the indicator lamp flashes 5 times on turning the 3D Eyewear on. In this case, early battery replacement is recommended. Ɣ Dispose of the old batteries as non-burnable rubbish, or in line with the waste disposal regulations in your local area. 1 Loosen the screw and remove the cover using with a precision Phillips (No.0, plus + ) screwdriver. Ɣ The screw is not removed from the cover.
)&& 67$7(0(17 7KLV HTXLSPHQW KDV EHHQ WHVWHG DQG IRXQG WR FRPSO\ ZLWK WKH OLPLWV IRU D &ODVV % GLJLWDO GHYLFH SXUVXDQW WR 3DUW RI WKH )&& 5XOHV 7KHVH OLPLWV DUH GHVLJQHG WR SURYLGH UHDVRQDEOH SURWHFWLRQ DJDLQVW KDUPIXO LQWHUIHUHQFH LQ D UHVLGHQWLDO LQVWDOODWLRQ 7KLV HTXLSPHQW JHQHUDWHV XVHV DQG FDQ UDGLDWH UDGLR IUHTXHQF\ HQHUJ\ DQG LI QRW LQVWDOOHG DQG XVHG LQ DFFRUGDQFH ZLWK WKH LQVWUXFWLRQV PD\ FDXVH KDUPIXO LQWHUIHUHQFH WR UDGLR FRPPXQLFDWLRQV +RZHYHU WKHUH LV QR JXDUDQWHH WKDW LQWHUI
IC STATEMENT This device Thi d i complies li with ith IIndustry d t C Canada d lilicence-exemptt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits.
NCC STATEMENT ᬊվ࣏⦷䴫⌒䕫ሴᙗ䴫㇑⨶䗖⌅ ㅜॱҼọ ㏃රᔿ䂽䅹ਸṬѻվ࣏⦷ሴ乫䴫ˈ䶎㏃䁡ਟˈޜਨǃ୶㲏ᡆ֯⭘㘵൷нᗇ㠚 䆺ᴤ乫⦷ǃ࣐བྷ࣏⦷ᡆ䆺ᴤ䁝䀸ѻ⢩ᙗ৺࣏㜭DŽ ㅜॱഋọ վ࣏⦷ሴ乫䴫ѻ֯⭘нᗇᖡ丯伋㡚ᆹޘ৺ᒢᬮਸ⌅䙊ؑ˗㏃Ⲭ⨮ᴹᒢᬮ⨮䊑ᱲˈ ៹・ণˈ⭘ڌі᭩ழ㠣❑ᒢᬮᱲᯩᗇ㒬㒼֯⭘DŽ ࡽ丵ਸ⌅䙊ؑˈᤷ䴫ؑ⌅㾿ᇊᾝѻ❑ 㐊䴫䙊ؑDŽ վ࣏⦷ሴ乫䴫丸ᗽਇਸ⌅䙊ؑᡆᐕᾝǃ、ᆨ৺䟛Ⱳ⭘䴫⌒䕫ሴᙗ䴫䁝ۉѻ ᒢᬮDŽ IC ST DDD As the battery is specially for this product, do not use it for any other device. Do not charge the battery. Do not pierce the battery with a nail, subject it to an impact, or dismantle or modify it.