Document of Conformity

ManualsBrandsWeidmueller ManualsBrass cable glands Ex e/d - Klippon® KDSWKDSW M50 BS O NI 2 G50

SCHEDULE

EU-TYPE EXAMINATION CERTIFICATE Sira 05ATEX1286X

Issue 5

This certificate and its schedules may only be

reproduced in its entirety and without change

CSA Group Netherlands B.V.

Utrechseweg 310,

6812 AR, Arnhem Netherlands

DQD 544.09 Rev 2018-04-20 Page 3 of 5

i. Following appropriate reassessment to demonstrate compliance with the requirements of the

latest editions of the EN 60079 series of standards, the documents previously listed in section 9,

EN 60079-0:2006, EN 61241-0:2006 and EN 61241-1:2004 were replaced by those currently listed,

the markings were updated accordingly, the Special Conditions for Safe use were also amended.

ii. Type of protection Ex t is upgraded from EPL Db to EPL Da. Following appropriate reassessment

to demonstrate compliance with the additional requirements for Ex ta, the markings were updated

accordingly.

iii. The use of Aluminium as a construction material was approved.

iv. The introduction of an alternative silicone and neoprene seal material was endorsed.

v. The service temperature range of the glands fitted with a neoprene seal was extended

to -35°C to +90°C.

vi. The KDSW and KDSX type cable glands, when installed in accordance with the manufacturer’s

instructions and with an appropriate enclosure on which they are fixed, are capable of providing

an ingress protection of IP66 and IP68 (50 metres 7 days).

vii. The removal of the special condition for safe use relating to enclosure volume, the remaining

conditions are renumbered accordingly.

Variation 6 - This variation introduced the following changes:

i. To modify/introduce the following changes to type KDSW/KDSX and KOSW/KOSX Cable Glands:

 KOSW/KOSX, the maximum inner sheath diameter accommodation for all gland sizes was recognised.

 KOSW/KOSX, gland sizes 50H, 63H, 75H, 80H and 90H were introduced.

 KOSW/KOSX, gland size 20S, revised ‘standard’ outer seal cable range from: 12.9/16.0 to 11.5/16.0

 KOSW/KOSX and KDSW/KDSX, gland size 16 with 0.38” NPT standard “trade size” introduced.

ii. The recognition of the ‘standard’ entry threads associated with every gland type’s gland sizes, in

accordance with newly introduced generic bill of material drawing(s).

iii. To permit all gland types, of parallel threaded entry threads, marked suitable for ‘Exe’ only to be modified

to have a minimum thread length reased to 10 mm from 8 mm.

iv. To permit all gland types of parallel threaded entry threads to be manufactured with a longer than

‘standard’ thread length to suit the end use application.

v. To permit all gland types to be manufactured with a size larger than the ‘standard’ entry threads listed

within the product description.

vi. To recognise all gland types with the following alternate threaded entry threads complying with the

requirements of EN 50018:2000. Are intended to be used as replacement entry devices within existing

installations with equipment that have threaded entries no longer permitted by the current edition of

EN 60079-1.

 NPSM ANSI/ASME B1.20.1:1983

 BSPT BS21:1985 (ISO 7/1; BS EN 10226-1:2004 ‘standard threads’

 BSPP BS EN ISO 228-1 :2003; BS EN ISO 2228-2:2003 class A full form ‘external threads’

 PG DIN 40430:1971

 ET BS 31:1940 (1979) Table ‘B’

All alternative trade size thread forms are manufactured within the dimensional parameter of the standard

entry threads of the gland entry body, and relevant constructional compliance length and engagement

requirements in accordance with their product markings.

vii. To recognise the actual seal ‘material specification’ reference as a replacement for the seal ‘material

supplier’.

viii. The brass materials of manufacture were updated and corrected.

ix. The aluminium materials of manufacture were updated and corrected.