User's Manual

ManualsBrandsWeccan Industrial ManualsElectronicsNew Jawbreaker

The following is just suitable for Heli with Gyroscope

Gyros in RC helicopters are most commonly used to control unwanted movement

on the yaw axis. When an RC helicopter rotates on its yaw axis, the direction the

nose points in changes. The yaw gyro's job is to sense any undesired rotation

around the yaw axis (clockwise or counter- clockwise rotation when viewed from

above) and to automatically correct the orientation of the RC helicopter.

THE GYRO WILL ENABLE A STABLE FLIGHT FOR THE HELICOPTER.

The safety instructions contained in this manual have to be

observed without fail!!

Warning with regard to placing the product

Do not use this product in an environment where it is exposed to extreme heat or cold, to dust

or to damp.

Avoid placing the product in an area that is not properly ventilated; do not cover the product and

do not place it on carpeting or similar surfaces.

Do not place cables behind the product's support. If the cables move (for example as a result of

stumbling) the product can fall to the floor!

Do not expose the product to direct sunlight, fire or other sources of heat that have an extreme

effect on the temperature.

Table of Contents

Intended use ............................................................................................................................

Safety instructions ...................................................................................................................

Unpacking and storing Jaw Breaker .......................................................................................

Getting to know Heli .................................................................................................................

Assembling Heli .......................................................................................................................

Secure the Flight Area .............................................................................................................

Flying Heli .................................................................................................................................

Taking off .................................................................................................................................

Steering ...................................................................................................................................

Landing .....................................................................................................................................

Trimming ...................................................................................................................................

Charging ...................................................................................................................................

Battery care information ..........................................................................................................

Flying tips ................................................................................................................................

Trouble diagnoses ..................................................................................................................

Technical data ........................................................................................................................

1) Switch the controller ‘ON.

2) Switch the helicopter on (‘ON/OFF, switch at the side

of the main body).

3) Place the helicopter on a flat, hard surface with the tail pointing

towards you. Extend the blades separately, or it may entangle each

other and cause the blade to break, or burn out the motor.

4) Make sure to move the left throttle lever to the lowest position first,

and then move it forward and backward. By doing this, the controller

will be fully forward armed and connected to the helicopter, with the

led light turn on. Please do not touch the helicopter when is searching

for signal from controller.

1) Move the left lever slowly

forward-the blades will start

to spin

2) As you move the left lever past the

halfway point, the helicopter will take off.

3) To ascend, move the left lever

further forward. To descend, slowly

move the left lever backwards.

Your Jaw Breaker helicopter is designed for outdoor and indoor playing. Allow a clear space around

you in all direction of at least 9.84feet. Make sure to play away from human beings or animals.

Outdoor use recommended

Begin on a flat surface

Keep away from any obstacles

Avoid flying windy weather conditions

Keep your eyes on the helicopter and be sure the

helicopter is within your eyesight

Have an adult accompany children when

flying

Keep away from any hard obstacles to avoid any

unnecessary damages

more than 9.84feet

more than 6.56feet

more than 9.84feet

Nose

Extend

Preparing to take off

Taking off

Flying Heli

Secure the Flight Area

1) To turn the helicopter left, move the right hand lever to the left.

2) To turn the helicopter right, move the right hand lever to the right.

3) To fly the helicopter forwards, move the right hand lever forwards.

4) To fly the helicopter backwards, move the right hand lever backwards.

To land the helicopter, slowly move the left lever backwards.

This helicopter is fitted with one trimmer control. This will allow you to adjust the flight of the helicopter

and erase any unexpected turning tendencies.

If the helicopter spins, you need to use the TRIM control to adjust the flying.

Push the left lever and keep the helicopter flying upwards between 0.5- 1 meter.

1) Turn the TRIM leftwards if the helicopter spins right.

2) Turn the TRIM rightwards if the helicopter spins left.

After trimming adjustment, you can also use the right lever to adjust the direction and

stop the spinning.

Steering Heli

Landing Heli

Trimming Heli

Notes

Charging: Connect the battery to the

charger as shown in the illustration,

do not force.

1) Never leave helicopter charging near a fire or other source of heat.

2) Never leave helicopter unattended during charging.

3) Always disconnect from the mains once fully charged, failure to do so WILL DAMAGE

THE BATTERY.

4) Never disassemble the charger.

5) Only use the charge that is provided

6) NEVER STORE BATTERY WITHOUT CHARGING FIRST, this will damage the battery.

7) Charge for a minimum of 10 minutes after use.

Charging

This helicopter is powered by dedicated Li-Po battery. Do not attempt to disassemble the battery or

replace with any after-market model.

1) Use only batteries recommended in this user manual.

Ensure that batteries are installed with the correct polarity.

2) Batteries should be installed under adult supervision.

3) Do not allow the battery to become over heated during charging.

4) Do not leave the battery charging overnight-switch off once the LED lights on the charger.

5) Do not use an after-market charger as this can damage the battery.

6) Do not short circuit the charging terminals.

PLEASE RETAIN THIS INFORMATION FOR FUTURE REFERENCE.

DO:

• Make sure battery compartment is secure.

• Use batteries of the correct size and type.

• Fit batteries correctly observing the plus and minus marks on the battery and compartment.

• Replace a whole set of batteries at one time.

• Remove dead batteries from equipment.

• Remove batteries from appliance before storing.

• Please remember that small button cells and AA batteries should be kept away from young

children as they could be easily swallowed. Seek medical advice if you believe a cell has

been swallowed.

DON’T:

• Mix different types of batteries.

• Mix old and new batteries.

• Dispose of batteries in a fire.

• Attempt to recharge ordinary batteries.

Battery care information

Problem Cause Solution

No control of helicopter

Helicopter is not flying

high enough

Helicopter lands too quickly

Helicopter spins

Recharge your helicopter

(see Charging instructions)

Push left hand lever fully forwards then

fully backwards

Do not fly it in strong wind as this will

limit or disturb your control

Gently move the left throttle stick backwards

when landing. Remember to give a slight burst

of power just prior to touch down

No function to controller

Power switch is turned ‘OFF’

Low battery in the helicopter

Low battery in the controller

Controller needs to be ‘armed’

Switch ‘ON’ controller and helicopter

Charge batteries in helicopter

Replace battery in controller

Turn controller ‘ON’

Blade speed is too slow

Battery is not fully charged

Left throttle stick moved

too quickly

Trimming adjustment See Trimming instructions section

Ease the left throttle stick further forward

Trouble diagnoses

Controller is turned ‘OFF’

Strong windy day

Turn the helicopter off, then on.

It will work again.

Helicopte

r stop by a heavy

impact or crash land.

1) You can expect a flight time of 5-7 minutes after fully charging the battery.

2) When taking off, do not move the left lever too quickly as this will cause the helicopter to topple

over. Move the left lever smoothly and continuously forwards until the helicopter takes off.

3) When landing, give the helicopter a burst of power just before touching down the floor to slow

down the speed and land smoothly.

4) Heli has a range of up to 25-30m. Be aware that the presence of electrical interference may

reduce this range.

5) During your first few flights, try to keep the helicopter close to the ground. This will allow you to

cut the throttle and safely land if you become disorientated.

6) Always turn the helicopter off immediately after flight.

7) After flying and before recharging, always turn the helicopter and controller off.

8) When not in use, the battery should be disconnected to avoid battery discharge.

9) Recharge the battery before putting it away.

10) Check for any damage: examine everything including blades and landing gear.

11) To avoid damage to the motor, always turn the throttle off if the blades become entangled in

anything or are prevented from turning, otherwise motors may burn out!!

Flying tips

Gyro function

Safety instructions

Read the user manual completely before commissioning, then refer to below important

information for correct operation.

1. To ensure safe operation, the user must comply with the safety instructions and

warnings contained in this manual.

2. The charger is designed in compliance with protection glass, ensuring that the

insulation (of the housing or the output cable) is neither damaged nor destroyed.

3. The charger should be kept out of the reach of children!

4. Avoid charging operation under adverse ambient conditions. This can lead to damage

to the sensitive electronics on the inside of the charger and thus to possible danger

for the life of the user. Adverse ambient conditions are:

-excessive humidity ( >75% relative, condensing )

-wetness and dampness, petrol

-dust or combustible gas, vapour or solvents

-excessive ambient temperature ( > approx, + 40 °C )

In the case of incorrect handling (excessive charging current or incorrect polarity), the

charger may be overcharged or destroyed.

5. Never unplug the plug-in power unit from the mains socket by the connecting cable!

Only hold it by the housing when disconnecting it.

6. Keep transmitting devices (mobile telephone, radios, etc.) away from charger, the

transmitter radiation arose can lead to interference in charging operation or to

destruction of the charger.

7. Never connect your charger to the mains voltage immediately after it has been taken

from a cold room to a warm one. The resulting condensation could, under adverse

circumstances, destroy the device. Allow the device to reach room temperature before

connecting it to the power supply.

Never touch the charger with wet or moist hands. There is the risk of a fatal electric shock!

The Jaw Breaker helicopter is fastened securely in place to avoid any damage during transit.

The helicopter is a delicate device so you must be careful when removing it from the package.

Ensure the contents are complete with:

1) 1 x helicopter 5) 2 x connectors ( spare part )

2) 1 x radio controller 6) 2 x tail blades ( spare part )

3) 1 x user manual 7) 1 x screw driver

4) 4 x main blades ( 1set ,2pcs up & 2pcs lower )(spare part )

Packaging box should be kept for proper storage of the helicopter after each use.

Warning: Improper storage of the helicopter may result in the blades bending or warping.

This will affect flight performance.

Getting to know Jaw Breaker

Installing batteries in the controller of your helicopter

Unpacking and storing Heli

Connect charging cable to helicopter

The ‘ON/OFF’ switch is located

at the side of the main body

Helicopter

Main blade

(Dual)

Stabilizer

Tail blade

Canopy

Trestle

ON/OFF switch

Jaw Breaker helicopter is delivered fully assembled and only requires some assembly.

See below.

Install batteries.

1) Pull and take out the battery cover, (pic.1)

2) Take off the battery cover from the controller, and then install 6pcs (AA) Alkaline

batteries in the batteries cage following the correct indicated polarity,

Notice: When the power indicator light goes off it means the power is running out,

you should renew the batteries.

US_S16_FL_902_A_IM ENGLISH VERSION(BLACK & WHITE) A4 X 12pcs 5F63FD2_New Jawbreaker

5F63FD2

CONFORMS TO THE SAFETY

REQUIREMENTS OF ASTM F963.

Do not mix old and new batteries.

Do not mix alkaline, standard (carbon-zinc),

or rechargeable batteries.

Contents and colors may vary.

FAST LANE IS A MARK OF (EST UNE MARQUE DE/ES

UNA MARCA DE) GEOFFREY, LLC, A SUBSIDIARY OF

(UNE FILIALE DE/UNA SUBSIDIARIA DE) TOYS“R”US,

INC.

MADE IN CHINA (FABRIQUÉ EN CHINE/FABRICADO

EN CHINA)

DISTRIBUTED IN THE UNITED STATES BY (DISTRIBUÉ

AUX ÉTATS-UNIS PAR/DISTRIBUIDO EN LOS

ESTADOS UNIDOS POR) TOYS“R”US, INC., WAYNE,

NJ 07470

IMPORTED BY (IMPORTÉ PAR/IMPORTADO POR)

TOYS“R”US (CANADA) LTD. (LTÉE),

2777 LANGSTAFF ROAD, CONCORD, ON L4K 4M5

DISTRIBUTED IN AUSTRALIA BY (DISTRIBUÉ EN

AUSTRALIE PAR/DISTRIBUIDO EN AUSTRALIA POR)

TOYS“R”US (AUSTRALIA (AUSTRALIE)) PTY

LTD.(LTÉE), REGENTS PARK NSW 2143

www.toysrus.com www.toysrus.ca

Caution: changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

-Consult the deal or experienced radio /TV technician for help.

The adaptor be periodically examined for conditions that may result in the risk of fire, electric

shock, or injury to persons and that, in an event such conditions, the adaptor should not be

used until properly repaired.

The consumer has a significant role to play in reducing the impact of waste electrical and

electronic equipment on the environment, through re-using or recycling such equipment.

Some of the components used in electrical and electronic equipment may contain hazardous

substances that can damage the environment and present a risk to human health if not property

disposed of.

The crossed out wheelie-bin symbol on the controller is to remind you that waste electrical and

electronic products should not be disposed of with household waste. If you are unable to re-use or

recycle your product it should be disposed of at a civic amenity site. Alternatively, you may take

your old product (of similar function) back to the store where you purchased your new product

within 15 days of purchase. You must take proof of purchase of your new product when returning

your old product to the store.

If the blades are damaged, it may not be repaired but has to be replaced with a new one.

Broken plastic parts can be sharp-edged. For your own safety, use protective gloves.

Flying time: 5-7 minutes

Charging time: 90-110 minutes

Operation range: 25-30m/ 82-100feet

Battery for the controller: 6 x AA (not included)

Battery for helicopter: 3.7V 380 mAh

Frequency: 2.4G

Features:Up/down,forward/backward,turn left/right

Main blade length: 26cm/ 10.23inches

Helicopter length: 30cm/ 11.81inches

Helicopter height: 15.5cm/ 6.1inches

Helicopter weight: 81.5g

Technical Data

Intended Use

1. The helicopter is delivered ready to fly and does not need to be charged before your first flight.

When you first receive it, do not charge it, just fly it. When the helicopter can no longer take

off from the ground, let battery cool for 5 minutes before charging. The best performance of

helicopter should be after 1st full charge. The performance during discharge process should

not be treated as defective.

2. This helicopter is delivered with partial-charged Li-Po battery separately, and never over charge

the battery. Normally first few charges, will take 1.5-2 hours. Then about 60-70 minutes for a full

charge. Once the charging light turns red,remove the charging cable from the helicopter. Let

battery cool for 5 minutes before flying.

This device complies with Part 15 of the FCC Rules.

Operation is subjected to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause

undesired operation.

1. Before charging, ensure helicopter is switched ‘OFF’.

2. Charging via controller

2.1 Pull out the charging cable from the back side of the controller

2.2 Turn ON the controller(Ensure the AA batteries inside controller not low power)

2.3 Plug the charging cable rod pin into the helicopter charging socket at the side

of the main body.(ref pic.1)

2.4 When in charging, the Red LED light on the controller turns green; when fully

charged the LED light turns red.

3. Charging time is about 60-70 minutes.

4. Remove the charging cable from helicopter.

5. Leave battery to cool for five minutes and the helicopter is ready to fly.

Note :Be sure that the battery in the helicopter has cooled down for 10-15 minutes after flying

before charging.

Examine the adaptor periodically for conditions that may result in the risk of fire, electric shock, or

injury to persons and that, in an event of such conditions, the adaptor should not be used until

properly repaired.

(pics 1)

3.7V

NOT INCLUDED

INCLUDED

JAWBREAKER

Indicator light

High/Low speed

mode button

Power ON/OFF

Trim

Right function lever

(Direction lever)

Throttle

switch

OFF

Fully forward

and backward