Section 2 Vista EasyPAY Kit Installation 2.1 Introduction The information in this chapter explains how to install the EasyPAY retrofit kit (PN 887122-001). Note: It is necessary to identify Side 1 and Side 2 of the dispenser in order to carry out the instructions that follow. Note that the dispenser ID plate is located on the lower left corner of the chassis frame on Side 1. See Figure 2-16 for illustration. 2.
Section 2: Vista EasyPAY Kit Installation 2.3 Removing the Bezels Complete the following steps to remove the bezels from the dispenser. Remove and save any temporary advertisement or instructional attachments from the bezel face. 2. Place an anti-static wrist strap (PN 916962 or equivalent) on your wrist and attach the other end of the wrist strap to an earth grounding point. 3. Disengage the advertisement (ad) panels. Unsnap the ad panel by pulling forward firmly on the top edge of the panel.
DJR-CD-1303A Section 2: Vista EasyPAY Kit Installation L W A Y N i f t F o r R e c e i p PTS Bar Area t E 2 2 3 1 4 3 1 Ad Panel (lowered) 3 Ad Panel Fasteners 2 Wing Fasteners 4 Function Switch Door Lock Figure 2-2 Wing Fasteners on Bezel 6. Rest the lower edge of the bezel on the dispenser and disconnect the following cables from the back of the bezel. a.
Section 2: Vista EasyPAY Kit Installation f. 2.4 Repeat steps 3 through 6 to remove the bezel on the other side of the dispenser. Lowering the DEMs Perform the following steps to lower the DEM(s) (Display Electronic Modules) to the service position. Use a slotted screwdriver to loosen two ¼ turn screws located at the top of the DEM. Refer to Figure 2-5. 2. Lower the DEM to the service position. 3. Repeat steps 1 and 2 for the DEM on the other side of the dispenser. DJR-FH/CD-1107A 1.
DJR-FH/CD-1321A Section 2: Vista EasyPAY Kit Installation DEM 1/4 Screws (2 Places) Dispenser Side View Side 1 Dispenser Front View DEM Service Position Figure 2-5 Lowering the DEM into the Service Position 2.5 Installing the Authorization Light Assembly (PN 887124) Complete the following steps to remove the blank panel from the bezel and install the authorization light assembly (PN 887124-001) in its place. Refer to Figure 2-6. 1. Locate the side 1 bezel removed earlier in paragraph 2.3. 2.
Section 2: Vista EasyPAY Kit Installation vistabks.cdr Back Vi e w of Bezel Blank Panel Receiving Slots (3 Places) Mounting Hardware (3 Places) Removing the Blank Panel from the VistaCard Bezel Back Vi e w of Bezel Receiving Slots (3 Places) Mounting Hardware (3 Places) Removing the Cash Access Door Panel from the VistaPay Bezel Figure 2-6 Removing the Blank Panels from the Vista Bezel 3.
Section 2: Vista EasyPAY Kit Installation Light Panel Cover Figure 2-7 Installing the Authorization Light Panel (PN 887124-001) 2.6 5. Secure the authorization light bezel assembly to the bezel using the mounting hardware set aside in Step 2. Use a ¼ inch nut driver to tighten the hardware. 6. Install authorization side 2 light assembly PN 887124-001 by repeating steps 1 through 5 for the bezel on the other side of the dispenser.
instpdb.cdr Section 2: Vista EasyPAY Kit Installation Power Supply Board Power Distribution Board Side 2 DEM Figure 2-8 Installing the Power Distribution Board (PDB) 4. 2.7.1 2.8 Return the power supply to the operation position after PDB is in place. Installing Power Supply Cables 1. Connect existing cable PN 880586-001 to P1 on PDB. 2. Connect P3 of existing cable PN 881984-002 to P3 on PDB. 3. Connect cable PN 886011-001 from J1 on PDB to J1 on power supply board. 4.
Section 2: Vista EasyPAY Kit Installation 2.8.1 Installing DCB Assembly in Electronic Heads Equipped with Printer Base PN 883727-001 If you are installing the DCB in a Vista with the "old" printer base PN 883727-001, refer to Figure 2-9. Figure 2-9 EasyPAY Assembly for Use With Old Printer Base PN 883727-001 1. If there are any ground wires attached to the lower DCPT frame, be sure to disconnect them before installing the DCB assembly. Once the DCB is in place, then reconnect. 2.
Section 2: Vista EasyPAY Kit Installation 3. 2.8.2 Secure the DCB assembly to frame on both sides of head with screws (PN 2-513161-0) provided in kit. Installing DCB Assembly in Electronic Heads Equipped with Printer Base PN 886208-001 To install the DCB assembly board in an electronic head equipped with the "Z" printer base Mounting Bracket, complete the following steps. Refer to Figure 2-10, Figure 2-11, and Figure 2-12. 1.
Section 2: Vista EasyPAY Kit Installation Install with connectors toward side 2 of electronic head. Figure 2-11 Installing DCB in Vista with Printer Base PN 886208-001 (Viewed from Side 1) Install DCB on heater fan side of "Z" bracket. Figure 2-12 DCB Mounted in Vista Printer Base PN 886208-001 (Viewed from Side 2) 2-11 July 2000 Part No. 920472 Rev.
Section 2: Vista EasyPAY Kit Installation J4 J8 J9 J7 J10 J11 J12 J3 Figure 2-13 DCB Connections 2.9 Installing Cables in Electronic Head Complete the following steps to install the new cables in the dispenser head. Refer to Figure 2-13 and Figure A-1 (Interconnection Wiring Diagram). Note: You may have to remove one or more existing tie-wraps to allow cables to reach appropriate locations when re-routed during this installation. 2.9.
Section 2: Vista EasyPAY Kit Installation 2.10 6. If needed, connect 4-pin connector of cable PN 886016-001 into 4-pin connector J4 on DCB board. 7. If needed, connect 6-pin end of cable PN 886016-001 to 6-pin connector with subpump controller wiring (see Figure 2-14). Otherwise, leave unconnected at this time. Modifying and Connecting Product Relay Cables (New Installations Only) Note: This is only done when installing the SPC.
Section 2: Vista EasyPAY Kit Installation 2.11 Addressing Lightboards The lightboards must be addressed before the system will operate successfully. Refer to the following table for lightboard dipswitch settings. Table 2-1 Dipswitch Settings for Addressing Lightboards Dip Switch 2 3 ON OFF OFF ON ON ON OFF OFF ON OFF OFF ON ON ON OFF OFF ON OFF OFF ON ON ON OFF OFF ON OFF OFF ON ON ON 2.
Section 2: Vista EasyPAY Kit Installation 2.13 Reapplying Power 15. Reapply power to dispenser and refer to the test instructions in Chapter 4 and the service manual "System Tests for Dispenser Electronics" (PN 920353). 2.14 Installing Patent and Serial Number Decal Refer to Figure 2-15 for the following steps: 1. Remove EasyPAY serial number and FCC decals from kit. 2. Locate the Dispenser ID plate on the lower left corner of side 1 on the chassis frame. 3.
Section 2: Vista EasyPAY Kit Installation 2.15 System Power-Up Complete the following steps. 1. To add power to the dispensers, turn power ON at the control power circuit breaker. 2. To turn power ON to the CAT, complete one of the following steps: a. For dual sided dispensers, turn power ON to the CAT at the function switch located on the side 2 DEM. b. For single sided dispensers, turn power ON to the CAT at the function switch located on the side 1 DEM.