User's Manual

ManualsBrandsWayne Dalton ManualsElectronicsWIRELESS KEYLESS ENTRY SYSTEM

Locate Keyless Entry Unit: within sight of door, at a

minimum height of 5 feet so it cannot be reached by

small children, and away from all moving parts of the

door.

Choose a convenient location that does not interfere

with the normal opening and closing operation of the

door, such as the door jamb.

CAUTION: The keypad

should be mounted a

minimum of 5 feet from the

floor to keep it out of the

reach of small children.

Two screws are included for

proper mounting into wood or

other similar material. If

you're mounting into some

other material, consult a

building contractor to insure

proper hardware is used for a

secure mounting.

Drilling Template

For Keyless Entry

Leave screw

head exposed

1/8" from wall.

Once you have

determined the

mounting

location, use the

drilling template

to determine hole

positions and drill

a 5/64" pilot hole

3/4" deep for the

two mounting

screws.

Insert screw into the upper pilot hole leaving the head of

the screw exposed about 1/8" from the wall. Slide and

lock the back keyhole slot over the exposed screw and

position the unit vertically. Remove battery door and

battery. Insert the lower screw and tighten. Replace

battery and battery door.

The following explains how your Keyless Entry can be

used to OPEN, CLOSE, START, and STOP your door.

Activate your keypad by pressing the ON/RESET

button; keypad will illuminate.

Enter your 4-digit PIN (personal identification

number); keypad will rapidly blink for 2 seconds and

then change to a slow blink; door will begin to move.

NOTE: If you inadvertently enter an incorrect code, the

keypad will still blink but door will not open. Reset with

the ON/RESET button and reenter your PIN number.

Unit remains active for next 15 sec. Pressing any

key, except the ON/RESET, will stop the door if

opening, or reverse the door if closing.

Pressing the ON/RESET button while keypad is slow

blinking will turn off the unit. Pressing ON/RESET

again will reset the unit so that the PIN can be

entered again.

Your new Model KEP2-0000 Wireless Keyless Entry

contains a state-of-the-art wireless digital transmitter

capable of operating an unlimited number of compatible

garage door openers.

For added security, your Wireless Keyless Entry utilizes

a "rolling code" technology that, each time the

transmitter communicates with the receiver, sets a new

code, selecting from millions of combinations, reducing

the possibility of electronic equipment causing unwanted

access.

For proper operation it is

important that you follow

the programming directions

and sequence as written.

Under normal operating conditions, the

battery should be changed once every 12

months. Dispose of used batteries

properly. To replace battery perform the

following steps:

A. Raise Keyless Entry Cover to expose

battery door.

B. Snap open door with a coin and remove

old battery.

C. Replace battery (12 volt MN 21) with

positive terminal to right and snap close

battery door.

Battery Door

Pre-drill a 5/64 pilot

hole 3/4" deep

Pre-drill a 5/64 pilot

hole 3/4" deep

Wayne Dalton Corp.

One Door Drive n Mt. Hope, OH 44660

800-305-4349 n Fax 800-884-5065

Mounting

Model KEP2-0000

Wireless Keyless

Entry System

How Your Keyless Entry

Operates Your Opener

Battery Replacement

P/N 288832

NOTE: This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference when the equipment is operated in

a residential environment. This equipment generates,

uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the

instruction manual, may cause harmful interference to

radio communications. However, there is no guarantee

that interference will not occur in a particular

installation. If this equipment does cause harmful

interference to radio or television reception, which can

be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by

one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and

receiver.

- Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV

technician for help.

Summary of content (3 pages)

PAGE 1
Pre-drill a 5/64 pilot hole 3/4" deep Mounting Locate Keyless Entry Unit: within sight of door, at a minimum height of 5 feet so it cannot be reached by small children, and away from all moving parts of the door. Choose a convenient location that does not interfere with the normal opening and closing operation of the door, such as the door jamb. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 2
PLEASE READ ALL INSTRUCTIONS THOROUGHLY TO FAMILIARIZE YOURSELF WITH THE PROGRAMMING PROCEDURE BEFORE BEGINNING. SAVE THESE INSTRUCTIONS FOR REFERENCE WHENEVER YOU WISH TO CHANGE YOUR PERSONAL IDENTIFICATION NUMBER (PIN) Before your Wireless Keypad will be able to operate the opener, there are several programming steps that have to be completed. FCC WARNING To comply with FCC rules, adjustment or modification of transmitter is prohibited. THERE ARE NO USER SERVICEABLE PARTS EXCEPT FOR BATTERY REPLACEMENT.
PAGE 3
Warning Statement THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.