'2& 86(5 0$18$/
tŚĂƚ͛Ɛ ŝŶĐůƵĚĞĚ ǁŝƚŚ ƚŚĞ ƉƌŽĚƵĐƚ;ŵŽĚĞů K Ϭϭ ĂŶĚ ŵŽĚĞů dtϬϲsϭ ƚŽŐĞƚŚĞƌ ĨŽƌŵ ƚŚĞ ^ĞĐƵƌĞϰ<Ϳ Installation Guide Tamper Tape ( %PDL Secure4K Camera & Dock Power Cord Secure4K Mount Plate & Adhesive Placement Guide DMS Module (Optional) Power Cord Locker Option A OBD-II Power Cord Option B Direct Wire Power Cord Please ensure the Secure4K and any necessary power components are secured and out of reach of passengers, especially young children and pets.
WƌŽĚƵĐƚ KǀĞƌǀŝĞǁ Using the Waylens Fleet App Camera Mount Screw Status LED mode Remote Camera Cable Holder microSD Card Slot Reset Button Solid Green Power On Solid Blue Idle Solid red Recording Blinks Blue Firmware Updating Blinks Blue and Red Error USB Type-C Power Waylens Button Function SIM Card Slot Waylens Button Status LED Click x1 Flip on WiFi On/Off Cli
Installing your Secure4K Option B Direct Wire Power Cord Park the car in a safe and convenient place for the installation 1. Turn off the engine and the accessory power. 1. Install power in the vehicle 2. Find the location and layout of your fuse box as well as the appropriate fuse type from the vehicle’s user manual. (two options - Direct Wire or OBD-II Power Cord) Option A NOTE: a.
b. Verify the fuse is a constant fuse by a multimeter to track voltage within the circuit across ignitions ON and OFF positions. c. If confirmed as a constant power fuse, remove the identified constant fuse from the fuse panel. Use the fuse puller tool if available. d. Remove the sleeve from the end of the yellow BATT+ wire and wrap the wire around one of the blades of the Constant Power fuse. e.
4. Install the Mount Plate on the Windshield SAFETY WARNING: Do not place the Secure4K in an area on the windshield where the product interferes with the driver’s field of vision or other in-vehicle sensors. The Secure4K should be mounted at the center top of the front windshield, optimizing visibility inside and outside the vehicle. NOTE: Do not place camera mount too low on windshield where visibility may be blocked by the vehicle itself, such as wiper blades or raised hood structures. 1.
6. Adjust Secure4K angle 7. Install and Calibrate the DMS camera DMS camera calibration process is to calibrate the DMS camera so that the DMS camera can detect the driver's face and sight line so that the DMS camera can better detect and upload DMS events. 1. Use a coin to loosen the Dock hinge by turning the adjustment slot counter-clockwise. To calibrate the DMS camera, Waylens Fleet App should be used. 1. Install the DMS camera in the recommended position as the picture shows. 2.
4 Adjust the camera position. There is a mask on the view of the DMS camera. The installer should keep adjusting the camera position to make the driver image fit in the mask. When the mask turned into green, the position of the DMS camera can be regarded as correct. 8. Insert and format the microSD card To prolong the usage, the new microSD card will be automatically formatted when the first time it was inserted to Secure4K.
Removing the Secure4K Secure4K SIM Card 1. Stop the Secure4K if it’s recording by pressing the Waylens Button on the Dock or turning monitoring off by fleet managers via API. Secure4K has pre-installed SIM card. Please do not remove the pre-installed SIM card. 2. Slide the Secure4K Dock to the left and carefully pull the camera away from the Mount Plate once you feel it release from the locking tabs.
FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
ISED RSS Warning/ISED RF Exposure Statement ISED RSS Warning: This device complies with Innovation, Science and Economic ISED RF exposure statement: Development Canada licence exempt RSS standard(s). Operation is subject to the This equipment complies with ISED radiation exposure limits set forth for an following two conditions: (1) this device may not cause interference, and (2) this uncontrolled environment.