Dual Mode Communication Terminal DM1000C/DMS1000C User Guide Draft CDMA v.
Handset D mode 1 2 3 4 Antenna Beltclip Attachment Speaker for Ringer Handset Battery Compartment 5 6 7 8 9 10 11 12 13 14 15 16 17 18 New Message LED Handset arpiece E LCD Display Function Keys Up/Down e Kys Menu and OFF Keys Scroll Left Flash/Delete Key Redial/Pause Key Headset Jack # Scroll Right Intercom Handset Microphone Handset Charging Contacts ii * Copyright © 2005 Waxess
Base 19 20 21 22 23 24 25 26 Base Speaker/Ringer LCD Display Function Keys Up/Down Keys Menu and Off Keys Intercom Key Speaker Phone Key Speaker Phone ON LED 27 Redial/Pause Key 28 New Message LED 29 Flash Key 30 DC IN 9V Jack 31 TEL LINE Jack 32 Corded Handset Jack 33 Battery Cover D Mode CT iii Copyright © 2005 Waxess
Introduction The D Mode CT is a unique, all-in-one cellular and landline communications device. This new product addresses the fast-paced convergence of landline and cellular, as well as transition from landline usage to cellular service usage at home. This innovative product combines landline (in the home) phone service with cellular (mobile) phone service. With this one device, you can now make and receive phone calls at home using your traditional home phone service or your mobile cellular service.
Contents Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv Web site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv Get ready . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Prepare . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D mode CT vi Copyright © 2005 Waxess
1 Get Ready Included items • Base • Belt clip • Cordless handset • Wall mount bracket • AC adaptor for base • Telephone cord • AC adaptor for cordless handset • User guide • Rechargeable battery for cordless handset D Mode CT DRAFT 6 1 Copyright © 2005 Waxess
• Choose Location Some important considerations: • Charge the handset for 12–15 hours before using it. • Locate the base near both a phone jack and a power outlet which is not controlled by a switch. • Keep the base and handset away from sources of electrical noise, such as motors and fluorescent lighting. • Leave enough room to raise both base antennas fully vertical. Desk or Table 1 Connect the telephone line cord to the TEL LINE jack and to a telephone jack.
d mode ct draft 6.book Page 3 Wednesday, March 2, 2005 10:33 PM 48091000), and connect it to the DC IN 9V jack and to a standard 120V AC. Wall mount 1 Attach the wall mount adaptor to the base. 2 Find the base AC adaptor (the larger adaptor, Model number 48091000), plug the connector into the DC IN 9V jack, then plug the telephone line cord to the TEL LINE jack. 3 Wrap the AC adaptor inside the molded wiring channel, then wrap the cord around the strain relief notch.
d mode ct draft 6.book Page 4 Wednesday, March 2, 2005 10:33 PM Install the batteries (Optional) The optional back-up batteries provide a reserve power supply so the base can operate for up to 30 minutes (depending on battery condition) in case of power outages or if power is cut off to the base for any reason. Backup power activates immediately when the normal power supply to the base is cut off. 1 Verify power is disconnected from the base. 2 Open the battery cover on the bottom of the base.
d mode ct draft 6.book Page 5 Wednesday, March 2, 2005 10:33 PM phone is idle. At the bottom of the screen, the text indicates which service lines are active. CEL is wireless service, and TEL is landline service. If you have connectED with your cellular service provider, the date and time may be set automatically. If not, see the next section to set the date and time manually. Signal level The Signal Level feature helps you find your strongest cellular service signal.
d mode ct draft 6.book Page 6 Wednesday, March 2, 2005 10:33 PM 3 Close the cover. CHARGE THE BATTERY 1 Find the cordless handset AC Adaptor (the smaller adaptor, Model number RGD41090500). Connect the AC adaptor to the DC 9V IN jack on the charger and to a standard 120V AC wall outlet. 2 Set the charger on a desk or table, then set the handset in the charger with the keypad facing forward. 3 Allow the battery to charge for 12–15 hours.
d mode ct draft 6.book Page 7 Wednesday, March 2, 2005 10:33 PM 2 Get set • Dialing mode 1 Press the MENU key on the base. The Menu appears. 2 Press the key so the highlight bar moves to Setup. This action is called “scrolling” throughout this guide. 3 Press F1 to “select” this menu item. This action is called “Press Select” throughout this guide. Another menu list appears. 4 Press the key and scroll to Tone/Pulse. 5 Press F1 to select this item and this screen appears.
d mode ct draft 6.book Page 8 Wednesday, March 2, 2005 10:33 PM 5 Enter the correct minutes, and press The AM/PM screen appears. OK. 6 Use the or key to set AM or PM and press The time format setting appears. OK. 7 Use the or key to set the time format and press The date screen appears with months showing. OK. 8 Use the keypad to enter the correct month. After entering the month, the cursor moves to the day. 9 Enter the correct day then press OK.
d mode ct draft 6.book Page 9 Wednesday, March 2, 2005 10:33 PM The TEL line ringer setting appears. OR Press Exit to cancel without saving changes. 6 Follow steps 1–4 above to choose a tone, and press A confirmation tone plays. Select. Set the ringer volume You can set the ringer volume while the phone is ringing or you can preset the ring volume through the menu. WHILE THE PHONE IS RINGING Press the or The choices are key to raise or lower the volume. Off-Low-Medium-High.
d mode ct draft 6.book Page 10 Wednesday, March 2, 2005 10:33 PM • Key beep Set the phone so that you hear a beep each time you press a button, or turn off the beep feature. 1 Press MENU, scroll to Ringer/Key Beep, and press Select. 2 Scroll to Key beep, press Select, then choose On or Off. 3 Press OK to enter the setting. A tone confirms the setting and the Ringer/Key beep menu appears. • Area codes Enter up to three area codes.
d mode ct draft 6.book Page 11 Wednesday, March 2, 2005 10:33 PM • Language 1 Press MENU, scroll to press Select. Setup, and 2 Scroll to Language, and press Select. The highlight bar shows the current language setting. 3 Scroll to the language you want, and press Select. A beep confirms the setting and the Setup menu appears. The menu appears in the language you selected. • LCD contrast 1 Press MENU, scroll to Setup, and press Select. 2 Scroll to LCD Contrast, and press Select.
d mode ct draft 6.book Page 12 Wednesday, March 2, 2005 10:33 PM 2 Scroll to Register and press Select. The display shows “Press and hold Intercom OK.” on base, then 3 Press and hold Intercom (at least two seconds) on the base until you hear a beep. 4 Then, press OK on the handset. Registration takes only a few seconds. When registration completes, you hear a tone and this message appears on the LCD screen. Deregister 1 Press MENU, scroll to press Select.
d mode ct draft 6.book Page 13 Wednesday, March 2, 2005 10:33 PM 3 GO! • Make a wireless call Cordless handset Speakerphone on base Corded handset on base •Press CEL •Enter number •Press CEL OR •Enter number •Press CEL •Enter number •Press CEL •Lift handset off base •Enter number •Press CEL •To end the call, Press OFF •To end the call, press SP-PHONE •To end the call, replace the handset Note: When making a wireless call, no dial tone is generated until the phone connects to the cellular network.
d mode ct draft 6.book Page 14 Wednesday, March 2, 2005 10:33 PM ON CORLDESS HANDSET DURING A CALL Press for louder or for softer. • Calling options Speed dial 1 Set up keys 0–9 with numbers in the phone book for speed dial. See “Enter numbers directly” on page 19. 2 Press and hold the appropriate number key, then press CEL or TEL. If you need to add or remove the number 1 or the area code for proper dialing in your area, see “Add/remove a 1” or “Add/remove area code” on page 10.
d mode ct draft 6.book Page 15 Wednesday, March 2, 2005 10:33 PM • The caller ID, if available, appears on the LCD screen Cordless handset •Press CEL •To end the call, press OFF twice Speakerphone on base •Press OR •Press CEL SP-PHONE •To end the call, press SP-PHONE Corded handset on base •Lift handset off base •To end the call, replace the handset • Answer a landline call When the phone receives a landline call • The base and all registered cordless handsets ring.
d mode ct draft 6.book Page 16 Wednesday, March 2, 2005 10:33 PM BASE TO HANDSET TRANSFER 1 Press Intercom, scroll to the handset (or base) that you want and press Page. The base and the handset involved in the transfer operation begin beeping (a different tone than with the Intercom function), and a message appears on the LCD. If there is no answer within 60 seconds, the page and the transfer are cancelled and you return to the call. You can press Exit to return to the call immediately.
d mode ct draft 6.book Page 17 Wednesday, March 2, 2005 10:33 PM are cancelled and you return to the call. You can press Exit to return to the call immediately. 2 Press Answer on the handset receiving the page. The call is now on hold, and the parties with the handsets can speak. 3 Press Exit on the handset that started the transfer. The call is now transferred to the receiving handset. On the receiving handset, you can press OFF or Exit to reject the transfer.
d mode ct draft 6.book Page 18 Wednesday, March 2, 2005 10:33 PM • Phone book Use the phone book to store up to 50 names and numbers. Enter names and characters Use the keypad to choose the characters you want. Each time you press a key, the letters on that key appear first as capital letters, then as lower case letters, then the number corresponding to that key.
d mode ct draft 6.book Page 19 Wednesday, March 2, 2005 10:33 PM Enter numbers directly 1 Press MENU, scroll to Memory, and press Select. 2 Scroll to Phone book, and press Select. 3 Scroll to Add new entry, and press Select. “Name?” appears in the display. 4 Use the letters on the keypad to enter the name (up to 16 characters) and press OK. Press OK to leave Name blank. “Number?” appears in the display. 5 Use the keypad to enter the number with area code and press OK. The Distinctive ring setting appears.
d mode ct draft 6.book Page 20 Wednesday, March 2, 2005 10:33 PM Enter numbers from Caller ID 1 While in the Caller ID log, scroll to the name/number you want to enter in the phone book and press Select. Call/Dial, Edit, and Delete appear. 2 Scroll to Save and press Select. “Name?” appears. 3 If the Caller ID shows a name, press OK to continue,or use the keypad to enter the name, then press OK to continue. 4 If the Caller ID shows a number, press OK.
d mode ct draft 6.book Page 21 Wednesday, March 2, 2005 10:33 PM • Messages Note: You must have a subscription to use these message services. Check with your service provider for details. Voice messages The D Mode CT works with both cellular and landline voicemail. SET UP VOICEMAIL 1 Press MENU, scroll to Setup, and press Select. 2 Scroll to Messages, and press Select. 3 Scroll to Voicemail setup, and press Select. The message VM Number (CEL)? appears.