link2 2-Channel Line Output Converter 10Vrms Output Ÿ Auto Turn-On Ÿ OEM Load Detect Compatible Owner’s Manual link2 www.wavtech-usa.
WARNING CAUTION This symbol means important instructions. Failure to heed them can result in serious injury or death. This symbol means important instructions. Failure to heed them can result in injury or property damages. WARNING • DO NOT DRIVE WHILE DISTRACTED. Any function that requires your prolonged attention should not be performed while driving. Always stop the vehicle in a safe location before performing any such function. Failure to do so may result in an accident.
CAUTION • STOP USE IMMEDIATELY IF A PROBLEM OCCURS. Failure to do so may result in personal injury or damage to the product. Return it to your authorized Wāvtech dealer. • HAVE AN EXPERT DO THE WIRING AND INSTALLATION. This unit requires special technical skill and experience for wiring and installation. To insure safety and proper function, always contact the authorized dealer where you purchased the product to have it done professionally. • INSTALL THE UNIT SECURELY WITH SPECIFIED PARTS.
Introduction Welcome to Wāvtech, exceptional mobile audio integration products for audiophiles. Our products are engineered to provide a truly remarkable listening experience. Built for the professional installer, our OEM integration and signal processor models are simply the best solution available for unlimited sound system upgrades while retaining the factory receiver.
Ž Power Supply Terminal: ‘ ’ “ For +12V battery, chassis ground, remote in and remote output wire connections. A minimum of 18AWG wire is recommended for power and ground connections. Always protect the +12V power wire with a 1-amp fuse. Speaker Level Input Terminal: For left and right channel speaker level (a.k.a. high level) connections to the source. Input signals ranging from 2Vrms to 20Vrms will produce up to 10Vrms RCA output from maximum to minimum gain.
Installation & System Wiring It is important to read this manual thoroughly before starting your installation and always plan accordingly. Before installing any Wāvtech product, disconnect the negative (ground) wire from the vehicle’s battery to avoid damage to the vehicle or yourself. Following all guidelines will help provide years of enjoyment with your Wāvtech link2 audio interface.
Remote Output (REM OUT): Use the remote output to provide a +12V trigger to turn on amplifiers or other aftermarket devices. This +12V output is generated internally by the interface when turned on either by REM IN or automatic sensing, and will provide over 500mA of continuous current for external devices.
Installation Notes Vehicle Description Ÿ Year, Make, Model: Ÿ Trim Level / Package: OEM Audio System Info Ÿ Head Unit (type, BT/AUX in, etc.): Ÿ Speakers (size/location, etc.): Ÿ Subwoofer(s) (size/location, etc.): Ÿ Amplifier(s) (location, output voltage, etc.): Ÿ Other: link2 Connections & Settings Ÿ Installed Location: Ÿ Wiring (connection locations, signal type, turn-on mode, etc): Ÿ Level Settings (gain position, max master vol, etc.
Internal Jumper Locations and Settings While all Wāvtech models provide external controls for main adjustments, there are also a few internal configuration jumpers available to resolve certain special vehicle or system conditions. The link2’s internal jumper locations and default settings are shown in the illustration below. To access these jumpers, simply remove the two top screws from each end panel and loosen two bottom screws on one side in order to easily remove the chassis top cover.
Specifications Frequency Response Input Impedance Input Sensitivity Max Input Voltage Output Impedance Max Output Voltage THD+N S/N Turn-On Trigger Remote Output Current Draw Operating Voltage Product Dimensions Max Flat (+0/-1dB) Extended (+0/-3dB) Spk Input Spk Input (max-min gain) Spk Input peak, <5sec cont.
Warranty & Service Care Wāvtech warrants this product to be free from defects in material and workmanship for a period of one (1) year when purchased from an authorized Wāvtech retailer within the United States. This warranty will be extended to a period of two (2) years when the installation is performed by an authorized Wāvtech retailer. A valid sales receipt is required to verify eligibility of purchase and installation.
v0820 Wāvtech® 1350 W. Melody Ave. Suite 101 Gilbert, AZ 85233 (480) 454-7017 ©Copyright 2020 Wāvtech, LLC. All Rights Reserved.