WBS-2400 & WBS-5800 Outdoor Wi-Fi Base Station Installation Guide Rev.
Note: To better reflect the value of Wavion products we are changing the name of our product family from Access Points (AP) to Wireless Base Stations (WBS), consequently the existing WS410 product name will be changed to Wavion WBS-2400.
Note: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: According to the FCC rules the WBS-5800 unit must only be used for fixed point to point applications with fixed clients.
Contents About This Guide ....................................................................... 5 Preface...................................................................................................5 Conventions ............................................................................................5 Contacting Technical Support ...................................................................6 2 Introduction ..............................................................................
Chapter 1 About This Guide Preface This guide details the Wavion WBS-2400/5800 installation procedures. The intended audience of this document is trained technical professionals. Conventions Caution: The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
About This Guide Contacting Technical Support For technical support, contact Wavion using these methods: 6 Address: Wavion Technical Support Wavion 6 Hayetzira Street, PO BOX 580 Yoqneam Illit, 20692 Israel Telephone: +972-4-9097343 Fax: +972-4-9097322 Email: support@wavionnetworks.com Web: www.wavionnetworks.
Introduction Chapter 2 Introduction WBS-2400/5800 a high capacity, IP services oriented Broadband Wireless access system. WBS-2400/5800 is a new category of Broadband Wireless Base Station designed from the ground up for metro-Wi-Fi deployments. The system employs wireless packet switched data technology to support high-speed IP services including fast Internet and Virtual Private Networks.
Chapter 3 Package Content Check that the package contains: POE injector unit with wall mounting kit Outdoor Unit with a connection to an external antennas 6 antennas Pole mounting bracket for the outdoor unit Allen head wrench with 4 screws Waterproof sealing tape for IP67 (band to sealing rubber) Additional Equipment and Tools required for Installation Ethernet cable (straight for connecting to a hub/switch) Crimping tool for RJ-45 connectors.
Package Content Addition tools and materials, including appropriate means (e.g. a pole) for installing the outdoor equipment. 1/4-inch flat blade screwdriver WARNING: ONLY experienced installation professionals who are familiar with local building and safety codes and, wherever applicable, are licensed by the appropriate government regulatory authorities should install outdoor units and antennas.
Chapter 4 Installing the Wavion WBS-2400/5800 Metro Base Station This guide explains how to safely install the Wavion WBS-2400/5800 Metro Base Station.
Important Safety Instructions WARNING: It is illegal to modify the construction of this product. Modifying the operating frequency or enhancing the transmit output power through the use of external amplifiers or other equipment is specifically disallowed by the "Telecommunications Act." WARNING: This device is for outdoor or indoor use with conditions that no harmful interference to authorized radio stations results from the operation of this device.
Caution: There are no user-serviceable parts inside. All service must be performed by qualified personnel. Caution Only UL listed parts and components will be used for installation. Use UL listed devices having an environmental rating equal to or better than the enclosure rating to close all unfilled openings. Caution To maintain Overvoltage (Installation) Category II, install a suitable surge suppressor device in the branch circuit to limit expected transients to Overvoltage Category II values.
Choosing a Location To ensure the optimal performance select the locations for the equipment using the following guidelines: The antenna (not-integrated on the front panel of the outdoor unit) should provide a direct, or near line of sight, with the sector location that need to be covered. The antenna should be aligned to face the CPEs that aim to be in service, higher the placement of the antenna, the better the achievable link quality (but not in all cases).
Mounting Strategies Consider the available mounting structures and antenna clearance when choosing a mounting location. Wavion outdoor unit WBS-2400/5800 should always be mounted with the top of the unit parallel to the ground, and with the antennas pointing upward and clear of obstruction. It is recommended to attach ground and data cables to the WBS-2400/5800 prior to mounting.
Figure 4.2 Example Mounting Locations on a Streetlight Using Hose Clamps Special hose clamps that include threaded holes are used by the mounting assembly to secure the WBS-2400/5800 to the mounting structure. Figure 4.3 demonstrate how to correctly use the hose clamps. The bands must be threaded through holes in the pole bracket, and then attached to either a vertical or a horizontal pole and tightened.
Mounting on a Pole/Streetlight WBS-2400/5800 can be mounted on a pole, tower, or streetlight. It is recommended to mount the WBS-2400/5800 on aluminum or galvanized steel structures. Note The Wavion WBS-2400/5800 must be mounted with the top of the unit parallel with the ground and with the antennas pointing upward. Note Before mounting the WBS-2400/5800, read the wiring instructions in Grounding the Wavion WBS-2400/5800 and Connecting a Data Port chapter. Metal/Wood/Streetlight Pole Mounting Figure 4.
Warning: Metal pole installation requires that the antennas are higher than the top of the pole. Note Be sure to mount the unit with the bottom panel, which includes the LED indicators, facing downward Note Antennas must be higher than the top of the metal pole and clear of any obstructions Note Mounting to wood, concrete, or painted poles requires primary grounding for the unit. Check the national electrical codes in your area for specific rules.
Note: The WBS-2400/5800 unit must be parallel to the ground. The unit can be rotated to obtain the correct position. Note Installations on large wooden poles require band clamps such as those supplied by Panduit, www.panduit.com. Such a product is listed as "Metal, Locking Tie Extra Heavy Duty 304 Stainless Steel". The tie and the installation tool are shown below To continue installing the WBS-2400/5800, see Grounding the Wavion WBS-2400/5800 chapter Grounding WBS-2400/5800 is shown in the figure below.
To ground the Wavion WBS-2400/5800: The Grounding screw is located on the side panel of the outdoor unit. To connect the grounding cable: 1. Connect one end of a grounding cable to the grounding terminal and tighten the grounding screw firmly. Do the following steps: a. Remove the nut and star washers from the grounding screw. b. Attach one star washer to the grounding screw. c. Attach #10 AWG bare copper wires with an M6 terminal ring to the grounding screw. d.
10 AWG wire to ground Earth Ground Earth Ground Earth 10 AWG wire to ground Earth WBS-2400/5800 110/220VAC Wavion POE INJECTOR Power + DATA Power + DATA Lightning Surge Protector D A T A POE cable enters building wall through conduit Customer PC 20 Figure 4.8 Grounding indoor injector by Network Protection Unit Figure 4.
Connecting Antennas This section explains how to connect the six antennas to the WBS-2400/5800X. In order for the WBS-2400/5800 to work properly, six antennas must be connected. Screw each of the 6 antennas into the N-Type connectors on the WBS-2400/5800. Figure 4.10 Connecting antenna WARNING: Only connect the unit to the power supply once all the antennas are connected. WARNING: Use caution when connecting the antennas. Undue haste can damage the unit.
Connecting Power and DATA The following describes how to apply power and data to the WBS-2400/5800X Caution: You must always install an external grounding wire. Perform a simple continuity check between the WBS-2400/5800and the ground termination point to confirm. You must also ground the outdoor data protection device to a ground rod or a bonded pipe. Make sure you have completed grounding before you connect power to the WBS-2400/5800X. The Wavion WBS-2400/5800 is equipped with two RJ45 connectors.
Note: National Electrical Codes (NEC) Article 800 requires the use of an Agency Listed (UL/CSA) Building Entrance Protector for all power and communications cables entering a building. Article 800 is intended to protect the building and occupants from fires caused by transient voltage and current surges. Note: This is not a mid-span powered device. Do not attempt to daisychain Power Over Ethernet devices.
Figure 4.12 Sealing rubber 7.
Figure 4.13 Sealing rubber 8. Tighten the band on sealing rubber for better sealing or using weatherproof Stripe. Note: Use high quality sealing material such as Scotch® 130C Linerless Rubber (attached to the product) Splicing Tape from 3M to ensure IP-67 compliant protection against dust and water. Figure 4.14 Weatherproof Stripe sealing Use high quality sealing material such as Scotch® 130C Linerless Rubber Splicing Tape from 3M to ensure IP-67 compliant protection against dust and water. 9.
POE port RJ45 Pin Descriptions Pin T/R Signal Color Description 1 T TXD+ Orange-White TX Data 10/100BaseT 2 R TXD- Orange TX Data 10/100BaseT 3 T RXD+ Green-White RX Data 10/100BaseT 4 R PoE+ Blue Power input, 55 VDC (+) 5 T PoE+ Blue-White Power input, 55 VDC (+) 6 R RXD- Green RX Data 10/100BaseT 7 T PoE- Brown-White Power input, 55 VDC (-) 8 R PoE- Brown Power input, 55 VDC (-) Safety Information for the Wavion WBS-2400/5800 The Federal Communications Commissi
Service Instructions The Wavion WBS-2400/5800 contains no user serviceable parts inside.
Chapter 5 Product Specification WBS-2400 The tables in this chapter contain specifications for the Wavion WBS-2400. Wireless Specifications IEEE 802.11b/g compliant Frequency band 2.4 - 2.483 GHz or TBD 802.11b: DSSS (DBPSK, DQPSK, CCK) 802.11g: OFDM (64QAM, 16QAM, QPSK, BPSK) Modulation TX Power Maximum 802.11b and 802.11g Beamformer Directed Power EIRP + Beamfroming gain: 42.5dBm EIRP Calculations Antenna Gain - 7.5 dBi Total EIRP - 34.5 dBm RX Sensitivity* 802.11b and 802.
-95 dBm @ 24 Mbps -92 dBm @ 36 Mbps -88 dBm @ 48 Mbps -86 dBm @ 54 Mbps Security Specifications Packet filtering via layer 2 & 3 WEP (64 bit or 128 bit) WPA: Encryption: WEP or TKIP Authentication: Pre-Shared Key or 802.
Physical Specifications Network Interfaces Auto-sensing 10/100 Ethernet Input from Wavion Injector Power Input Power from a Wavion POE Injector. Indicator Lights Ethernet port LED Link/Act indicator System Status LED indicator RF channel status indicator Physical Dimensions Antenna Diameter W360.8 (mm) L389.9 (mm) Height H55.6 (mm) Weight 4.12kg (with post clamp ,without antenna) , 3.
Environmental Specifications Operating Temperature Range -40°C to +55°C (without Sun Shield) -40°C to +60°C (with Sun Shield) Storage Temperature Range -45°C to +85°C Weather Rating IP67 Wind Survivability 165 mph Salt and Fog Rust Resistance MIL-STD-810F 509.4 Shock and Vibration ESTI 300-192-4 spec T41.E Transportation ISTA2A Approvals RF Safety EMC FCC CFR 47 part 15, Sub Part C ETSI 300 328 V1.7.
Chapter 6 Antenna 2.4GHz Specifications and Patterns The chapter describes antenna specifications and patterns for the antennas supplied with the Wavion WBS-2400. SF-245W 2.4GHz Omnidirectional Antenna Specifications Pattern 2400-2500MHz Gain: 7.4dBi Length: 17.5 inches Weight: 4.7 oz -3dB Beam-width: 20 degrees Cross Polar Rejection: 15dB + Max Power: 50 watts Max wind survival: 150MPH + Wind Load: 7.
Installation Guide 33
Wavion Networks
Installation Guide 35
MT_341017NA_SN_101_EL 2.
Installation Guide 37
Wavion Networks
Chapter 7 Product Specification WBS-5800 The tables in this chapter contain specifications for the Wavion WBS-5800. Wireless Specifications IEEE 802.11b/g compliant Frequency band 5.725–5.850 GHz 802.11a: OFDM (64QAM, 16QAM, QPSK, BPSK) Modulation • Max. power per antenna: 19dBm (FCC version - Maximum transmit power will vary by channel and data rate) TX Power Maximum Beamformer Directed Power EIRP + Beamfroming gain: 43dBm EIRP Calculations Antenna Gain - 7.5 dBi Total EIRP - 35.
dBm @ Mbps -86 dBm @ 54 Mbps Security Specifications Packet filtering via layer 2 & 3 WEP (64 bit or 128 bit) WPA: Encryption: WEP or TKIP Authentication: Pre-Shared Key or 802.
Physical Specifications Network Interfaces Auto-sensing 10/100 Ethernet Input from Wavion Injector Power Input Power from a Wavion POE Injector. Indicator Lights Ethernet port LED Link/Act indicator System Status LED indicator RF channel status indicator Physical Dimensions Antenna Diameter W360.8 (mm) L389.9 (mm) Height H55.6 (mm) Weight 4.12kg (with post clamp ,without antenna) , 3.
Approvals FCC CFR 47 part 15, Sub Part C RF Safety EMC 42 Wavion Networks TUVus EN 60950-1:2001+A11:2004 IEC 60950-1:2001 First Edition Information Technology equipment – Safety – Part 1 FCC CFR 47 Part 15, Sub Part B, Class B (USA)
Chapter 8 Antenna 5.8GHz Specifications and Patterns The chapter describes antenna specifications and patterns for the antennas supplied with the Wavion WBS-5800. MT-462007-N 5.8GHz Omnidirectional Antenna Frequency Range: 4900-5875MHz Peak Gain: 8.5dBi ± 1 dB Regulatory Compliance: RoHS, CE 0682 VSWR: 2.0:1 (max) Input impedance: 50 (ohms) Connector: N – Type male Weight: 0.
Gain versus Elevation The following graphs show the gain versus elevation at 0 degrees azimuth angle at the following frequencies: 1. 5.725GHz 2. 5.
Installation Guide 45
Chapter 9 Installation Accessories This chapter describes the accessories available for the WBS-2400 and ordering information.
Ethernet Cables Description Manufacturer Part Number Distributor Contact Information Outdoor CAT5e double jacket 4-pair data cable Teldor 8393204101 G.Bares Tel: +972-(4)8215450 Sun Protection Description Product Name Part Number Sun Shield for WBS-2400/5800X, extends upper operation temperature range to +60°C WA-SUNSH 27009023 Lightning Protection Description Manufacturer Part Number Contact Information Data protection device Hyperlink HGLNCAT5-2 www.hyperlinktech.
Chapter 10 Wind Loading Considerations This chapter describes wind loading considerations for the WBS-2400/5800X. Note: It is recommended to evaluate the static and dynamic load bearing capabilities for each assembly and installation individually. It is your responsibility to evaluate the load bearing capabilities of the structure. The Wavion WBS-2400/5800weighs approximately 16 lbs, including all mounting hardware.
Chapter 11 Acronyms Acronym Description 2P Two-Phase or Split Phase 2W Two-Wire 3W Three-Wire AC Alternating Current ANSI American National Standards Institute AWG American Wire Gauge C Celsius CAT Category CCK Complementary Code Keying CFR Code of Federal Regulations CSA Canadian Standard Association dB Decibels dBi Decibels Relative to an Isotropic Radiator DBPSK Differential-Binary Phase-Shift Keying DC Direct Current DQPSK Differential-Quadrature Phase-Shift Keying DSSS
Mbps Megabits Per Second MHz Megahertz MIL-STD Military Standard N Neutral NEC National Electrical Codes NEMA National Electrical Manufacturers Association OFDM Orthogonal Frequency Division Multiplexing P Phase PE Protective Earth PoE Power over Ethernet RJ45 Registered Jack 45 RSS Received Signal Strength Rx Receive RXD Receive Data TUV Technical Inspection Association Tx Transmit TXD Transmit Data UL Underwriters Laboratories VAC Voltage (Alternating Current) VCC
Chapter 12 Appendix A: WBS-2400/5800 Product list Part Number 12406101 12406102 12406104 15806101 Product namer Product description WBS-2400-FCC Spatially adaptive, multi radio 2.4GHz WiFi base station, 6 antenna FCC/TUV compliant WBS-2400-EU Spatially adaptive, multi radio 2.4GHz WiFi base station, 6 antenna ETSI / CE compliant WBS-2400-IL Spatially adaptive, multi radio 2.4GHz WiFi base station, 6 antenna Israel compliant WBS-5800-FCC Spatially adaptive, multi radio 5.
