Installation Guide Rev 1.
Revision Chart Version 1.
TABLE OF CONTENTS Revision Chart ............................................................................................................................................ 8 1.0 Introduction ....................................................................................................................................... 10 2.0 Items Included in Package: .............................................................................................................. 10 3.0 Dimensions and Mounting .......
1.0 Introduction This guide explains the installation procedure of Spectra Controller. The back side of the controller has all the connecting ports and the front side has the company’s logo which glows when unit is powered ON. 2.0 ITEMS INCLUDED IN PACKAGE: Item Specs Quantity 1 Spectra Unit Refer to Spec sheet 1 2 Power Supply Meanwell 12V/3.
3.0 DIMENSIONS AND MOUNTING The Dimensions of the Spectra unit without mounting brackets are 260x170x43.
Rack Mount Brackets These two brackets can be screwed on sides of spectra unit in order to mount it on rack.
4.0 Picture of Spectra controller unit 4.1 Front View: 4.
5.
Details are as follows: Power 2.5mm DC Jack to Power up the unit using Meanwell supply (12V, 3.34A) included in package. CDU/TSU ports RJ45 Ports marked CDU and TSU can be used to drive Display devices and HTSU over RS485 protocol (Active Hub will be needed). Audio Two RJ45 ports for connecting 8 Ohm speakers. Volume Knob for controlling volume level. Debug port (DB-9 Connector) A standard FTDI cable (RS232 to USB) can be plugged into this port for debugging purposes.
6. 0 Setting up Spectra to drive Displays and TSUs 6.1 Setting up Spectra in wired system 6.1.
Description: • Connect the Spectra controller as shown in wiring diagram above. • When using TCP Active Hub, Spectra can be configured to transfer data for displays (CDUs, SDUs and PDUs) and HTSUs over LAN connection to TCP Active Hub. • TCP Active Hub must be connected to same local network as Spectra is connected to.
6.1.2 SERIAL MODE (OVER RS485) Serial Mode is to be used when connecting the system with the old Active Hub (old unit with Serial connection only). It can be used with TCP Active Hub as well (Serial + LAN connectivity), however with TCP Active Hub LAN mode is recommended.
Description: Connect the Spectra controller as shown in wiring diagram above. 1) Driving displays (CDUs, SDUs and PDUs): In order to drive displays connect one end of patch cord (RJ45 connector at both ends) to port marked “CDU” in Spectra and other end to Active Hub/TCP Active Hub port marked “IN”. All the End Devices (Displays) can be connected to any of the 16 output ports of Active Hub. Refer to Active Hub installation guide for further details.
7.0 Providing LAN connectivity: Connect a LAN cable/Patch cord from network switch to LAN port on Spectra controller in order to provide internet or LAN connectivity. 8.0 Connecting Speakers: There are two RJ45 ports provided on Spectra unit marked “AUDIO” ,which can be used to drive two 8 ohm speakers. RJ45 cable connection for speaker (T-568B): Use White Orange and Orange pair to connect speaker wires. Volume knob is provided to change volume level, rotate it clockwise to increase volume.
9.0 DEBUGGING: This cable will be used for troubleshooting purposes only. 10.0 UPGRADING SPECTRA LAN Connectivity 21 A basic version of EMportal (Web based management console) and WebTSU will already be installed in the spectra controller. User may need to upgrade the Spectra engine to the latest version. For upgrading the engine to the latest version, user first must change the IP setting via USB.
Insert USB in the Spectra engine usb port. Take it off and connect it to a PC. A file named ‘oldipsetting’ would have been created. Edit this file and rename it to ‘newipsetting’ and configure the IP address as per to the branch setting. o oldipsetting > rename to newipsetting and edit the IP address. o Newipsetting > reboot the engine.
CONTACT US In case you may require further assistance regarding the Spectra Controller, please contact us at support.int@wavetec.com Head Office United Arab Emirates, Dubai Wavetec FZCO Address: Industrial License No. 175 Light Industrial Unit # 9 Dubai Silicon Oasis P.O. Box 341133 Phone:+971 (4) 326 31 93 Fax: +971 (4) 326 31 92 Email:support.int@wavetec.com Web: http://www.wavetec.
FCC Caution： This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
