WX) WIRELESS NETWORKING SPEEDWELL OPERATOR'S MANUAL Version 3.2 841-358-9283 941-355-0219 FAX 800-721-9283 www.speedian.
SPEED AN Plus & 10 Product License Agreement I ts stentorian for veers of Wave Wireless hardware and flatware to fake fie to read this License Agreement lactated with this software PRIOR TO FITS USE, The Customer or Reseller has poi a Li cease fee to Wave Wireless for use of this software on one bridge of bridge/outer, This License docs not extend 10 any copyrights to the program nor does it license use of the program on muse than one bridge or footbridge wor to make copies of the program for distribution o
SPEEDWELL Plus & 10 french test time at an hourly fat bf S85 LS. per hour for testing and troubleshooting, Out of waterlily repairs will be pierced at tn hourly rae af $85 US. per hour plus parts. All shipping charges will be the responsibility of the customer wader the above circumstances, Onsite Service Onsite services for troubleshooting add repair are billed 28 the rate of $860 US.
secs lia Contents 1. Introduction Features and Benefit Features Chart... 2. Buick Start... System Description. Installation Steps. Application Drawing Antenna Alignment and Polarization 3. Using Configuration. 4. Configuring the SPEEDWELL Plus 23 General Setup... 5 Transport Methods. 5. Configuring the SPEEDWELL 10, General Setup. 35 Transport Method 6. Bridging Setup... Protocol Filtering. MAC Filtering. Permit Ethernet Broad Permit Ethernet Multics Advanced Features.
SPEEDWELL Plus & 10 Features and Benefits Transparent Ethernet Bridging with Advanced Filtering for Security and Network Reliability SPEEDWELL supports what is known as Transparent Ethernet Bridging with no Spanning Tree or Source Routing Supp nice the router is intended to provide network sit between a Local LAN and a campus or enterprise wide network, and since using multiple bridges in tanning Tree could compromise this security, the Spanning Tree scenario is not supported.
Sect al Feature Chart Hardware Supported 10/1 ABASE-T Ethernet Card SPEEDWELL Wireless Cards Bridging Features Transparent Bridging Filtering by Ethernet Multi cast, Broadcast and Bad Packets Filtering by Protocol Filtering by Ethernet Address Pair Generic Ethernet Tunneling through [P Networks Learned Table Lock down Expanded IP ARP Supp Automatic Broadest Storm Protection and Notification SNIP Features 1P “ping” Support IP SNIP Support (MIB 1, Ethernet, Interface, SNIP, and Bridge MIB) IP SNIP Wave L AN T
SPEEDWELL Plus & 10 SPEEDWELL Wireless Router Quick Start ‘The SPEEDWELL routers are high speed, long range wireless: ridges that provide connectivity to remote Ethernet networks. The local router communicates with a remote router on another LAN. This effectively creates an extended wireless network, spanning sites situated up to 25 miles apart. In this way a central Ethernet LAN may be connected with one or more branch office LAN.
SPEEDWELL HT Installation Steps Step 1 Line of Sight Before installing the antennas and bridges make sure clear line of sight exists. Line of sight can be defined as each antenna being able to clearly see the other antenna or being able to see the remote locations when viewing from the base location. Be sure to look level with the center of origin of the transmission (the middle of the antenna). Do the same from the remote location.
= SPEEDWELL Plus & 10 Step d Ground the Antenna 1. Mount he lightning arrest or to a solid surface. 2. Run the grounding wire from the lightning arrest or to a proper ground source such as a grounding rod or 100f ground wine. 3. Seal the entire lightning arrest or with the black waterproof sealant insulation putty that comes in the installation kit. Note: The lightning arrest or is NOT waterproof. See the diagram on page 2-5. Step § Connect the Wireless Bridge to the Power Supply 1.
SPEEDWELL Pius & 10 Cable Connectors {Bela with Putty) SPEEDWELL RN TT Ethernet Network / / Power Outset Lightning Arrest {Seal with Putty) Ground All outdoor cable connections and lightning restorers must be insulated with waterproof electrical putty All personnel should stay at least 1 Meter (3.57) from antenna to avoid exposure to possible microwave energy.
SPEEDWELL Pius & 10 Antenna Alignment and Polarization The antenna must be aimed so that when you look out from the center of the antenna iris pointing toward the receiving antenna on the other building. The radio signal shoots out the end of the antenna like a wide-beamed flashlight. Vertical Polarity Horizontal Polarity Europe United States zed antennas work Bast. This Is because most prized.
: Cesar Windows 93/NT 4.0 SPEEDWELL Configuration Installing the Windows 95/NT 4.0 SPEEDWELL Configuration Shut down all programs and applications before running Setup on Disk 1 of the floppy diskettes provided with your SPEEDWELL.
SPEEDWELL Plus Exporting and Importing a Configuration Once you have opened a remote SPEEDWELL router, you can take a “snapshot” of the current configuration with the “Save Con fig function. This function will result in creating a CNF file. The extension CNF is used to denote the spe | exported binary configuration file.
Sam l eT Setup Menu The third menu from the eft is the Setup Menu. In this menu are the screens vou will use to configure your SPEEDWELL Plus routers. Below are descriptions of the menu items and the settings found on their respect rive screens. General Setup | BE ene Enable Bridging The transparent bridging function will be enabled when this is item is checked. If you want the router to perform the bridging function,you must enable this.
SPEEDWELL Plus & 10 Enable IP/UDP/TCP Security Filters This option is not available at this time. Enable Apple Talk Security Filters This option is not available at this time. Enable Nov ell Security Filters This option is not available at this time. Ion able Watchdog Reboot Timer This feature instructs the bridge fo reboot in the event that the bridge fails to receive any incoming packets, from any port, for a period of 10 minutes.
; cane tas a ry Slave, Backup and Perm are settings used in very specific applications. These settings will be enabled by default if the SPEEDWELL router you purchased was designed to utilize these settings. Misconstruing the settings on this screen can re rider the SPEEDWELL router inoperative. Please call a Wave Wireless Networking Technical Support Engineer before making any chaises to the Interface or Advanced Interface Setup screen.
SPEEDWELL Plus ‘Wave AN Network ID (WIND) « The Network ID assigns a number used to identify the transmissions of an Interface.