Installation Instructions

ManualsBrandsWatt Stopper ManualsElectronicsDLM Wireless Slim Switches

Wattstopper

DLM Wireless Slim Switches with IPv6/Bluetooth(R) Low Energy Technology

Installation Instructions • Instructions d’Installation • Instrucciones de Instalación

No: 31762 – 12/21 rev. 1

Catalog Numbers • Les Numéros de Catalogue • Los Números de Catálogo:

LMSW-610-S, LMSW-611-S, LMSW-622-S, LMSW-641-S

Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China

SPECIFICATIONS

Power Supply .......................... Battery powered, CR2032 Battery, 3VDC

Connection to DLM Network .... Wireless via LMRC-611 room controllers

.............................................................................. or LMBC-650

Wireless Radio .................................Single, Concurrent 802.15.4 and

............................................ Bluetooth Low Energy, 2.4GHz

Wireless Communication

IPv6 Mesh (6LoWPAN) Range ....................................up to 60 ft.

Bluetooth low energy Range .......................................up to 60 ft.

60 ft. max. between LMSW-6xx-S and room controller or bridge

Wireless Encryption .................................. AES-128 bit symmetric key

Environment ........................................................ For Indoor Use Only

Operating Temperature ........................32° to 140°F (0° to 60°C)

Storage Temperature ......................... 23° to 140°F (-5° to 60°C)

Relative Humidity ..............................5 to 95% (non condensing)

Compliance/Regulatory

UL, cUL, FCC, IC

RoHS

Bluetooth certified

NOTE: Installation shall be in accordance with all applicable

regulations, local, and NEC codes

Once paired to a wireless room controller or wireless bridge,

adjustment via the DLM Conguration App or LMCS-100 may

be required to meet the local energy code where installed.

The DLM Wireless Slim Switches are wireless battery powered wall

switches intended for operation with wireless room controllers or

wireless bridges in hybrid rooms.

Do not apply cleaning solvent directly onto unit. Apply cleaning solvent onto

a cloth, then wipe the unit to clean it.

BUTTONS AND INDICATORS

Status/Battery

Life LED

Tap when load OFF: Turn ON to last level

Tap when load ON: Go to full bright

Press & Hold: Ramp Up

Tap: Fade to OFF

Press & Hold: Ramp Down

Button(s) can be set

to toggle on/off or

to function as a

scene switch

Configuration Button

(Right side of Legrand badge)

LED Color Function

Red/Green/Blue

Flash

Unit Boot Up

Green, 1 Blink Config Button Pressed

Blinking Green Push to Pair Mode

Red, 1 Blink In normal operation, if any button

press, indicates low battery

Also blinks if Reset button on back is

pressed

Blinking Red Push n’ Learn Mode

White Button or Rocker pressed during

normal operation

LMSW-610-S LMSW-611-S LMSW-622-S LMSW-641-S

Summary of content (8 pages)

PAGE 1
Wattstopper ® DLM Wireless Slim Switches with IPv6/Bluetooth(R) Low Energy Technology No: 31762 – 12/21 rev.
PAGE 2
INSTALLING THE SWITCH DLM Slim Switches support two installation methods: surface mount or wall-box mount. NOTE: Before mounting, the battery protection tab should be removed. Surface Mount: Surface mounting requires use of a Legrand radiant® wall plate (not included). The adhesive pad is suitable for mounting to multiple materials including drywall, metal, wood, glass, and some plastics. 1. Press and jiggle the wall box screws from the rear to remove them from the switch. 2.
PAGE 3
WIRELESS ROOM CONNECTION LMBR-650 For networking and managing rooms, floors, and building (not needed for stand-alone rooms) IPv6 Mesh for networking of DLM rooms and devices over 6LoWPAN Bluetooth low energy communication for mobile App support LMRC-611MCC LMSW-611-S Wireless Slim Switch Distance Recommendations: 60’ max between LMSW-6xx-S and mobile device 60’ max.
PAGE 4
SETTING UP A ROOM NETWORK BY PAIRING DEVICES Pair wireless devices to a room controller to create an individual room network and enable Plug N’ Go operation. Device pairing can be done by using Push-to-Pair (PtP) mode on the room controller and all other wireless devices, or by using the DLM Config App or LMCS software. To pair devices in a network, they must all have the same wireless channel and Network ID. By default the channel is 15 and the Network ID is 1.
PAGE 5
. Exit PtP mode. From any device, press the Config button 3 times. After a few seconds, the LED on each Room controller, switch or sensor currently in PtP mode will flash either white or a red/green/blue sequence and reboot, leaving the default network and migrating to the new network. Then, the LED on the room controller will flash blue and the pairing process finishes.
PAGE 6
PLUG N’ GO OPERATION (PNG) Loads in fully wireless rooms will automatically bind to LMSW-6xx-S switches based on the behavior detailed for each switch below. NOTE: Wired loads in hybrid rooms will have no automatic PnG binding and must be configured with LMCS-100. However, after a switch is paired into the room, the configuration button can be pressed once to toggle loads in the room in order to verify communication and operation.
PAGE 7
UNIT ADJUSTMENT USING PUSH N’ LEARN NOTE: Although Push n’ Learn™ can be used to modify load binding for wireless switches, Wattstopper recommend using the DLM Config App for ease of use and available features. NOTE: Push n’ Learn is not available for wireless switches paired to hybrid rooms with wired controllers.
PAGE 8
FCC REGULATORY STATEMENTS This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.