User's Manual

ManualsBrandsWatt Stopper ManualsElectronicsMRD2, MRD3, MRD4, MRD5, MRD6, MRD8, MRD9

2, 4

Note: when you

see Ú in the

instructions, press

the top and the

bottom of the

device rocker at the

same time

How to install and use the

wireless Miro

room preset

controller (MRD6)

English

Read and retain these instructions

Français

Español

Ready?

Application

For more information on designing,

installing and using wireless Miro

systems, and for expert technical

help, call 1-800-223-4185, or visit our

web site at:

www.passandseymour.com/miro

Use one or more wireless Miro

room

preset controllers in a room with any number

of wireless Miro

dimming or non-dim

devices.

Used this way, the wireless Miro

room

preset controller provides instant recall of

four user-recorded lighting scenes (or

presets), plus off, as well as an overall

mastering of the room’s light level.

Need more than four scenes? Use two or

more wireless Miro

room preset

controllers for up to sixteen recordable

scenes per room! (explanation below).

The wireless Miro

room preset controller

may be combined with the following wireless

Miro

control devices to control a room:

 Incandescent Dimmers

 Universal Dimmers

 High Power Wall-mount Dimmers

 Non-dim Switches

 Silent Fan Controls

 Plug-in Lamp Modules

 Plug-in Appliance Modules

 Remote Actuators

 Handheld Room Remote Control

Note: for whole-house control, use a

wireless Miro

whole-house preset

controller

Installation

1. Disconnect power to circuit by turning

circuit breaker OFF before installation.

2. Remove existing wall plate and switch.

3. Strip existing wires ½”

4. Wire the LINE (black), NEUT (white),

and GND supply wires to the

correspondingly marked screw terminals,

following the wiring diagram in figure 1

5. Mount using a Miro

wall plate,

following instructions provided

6. Switch the circuit breaker back ON

INSTALL IN COMPLIANCE WITH ALL

APPLICABLE CODES & STANDARDS.

Failure to follow these instructions may

cause personal injury or equipment damage.

Get Set…

Configuration

Figure 2

To prevent interference between neighboring

systems, wireless Miro

devices must

acquire a unique house ID before use. It’s

simple!

1. With all devices installed and energized,

check that every wireless Miro

device

is showing a yellow LED. If not, check

that the circuit breaker is on and that the

device is correctly installed.

2. All devices in a home must be ‘bound’ to

the same home ID. For a new wireless

Miro

installation, simultaneously press

and hold the top and bottom (Ú) of any

device paddle for 2 seconds. Its LED

flashes yellow, indicating that it has

acquired a unique House ID.

3. Check that all other wireless Miro

device LEDs are flashing green,

indicating that they have acquired the

same House ID.

4. Return to the first device, and press Ú

again for 2 seconds. All device LEDs

revert to green, indicating that house

binding is complete.

Note: if you’re adding the device to an

existing wireless Miro

installation, simply

GND

NEUT

LINE

Figure 1

Supply

Wire

Summary of content (5 pages)

PAGE 1
How to install and use the wireless MiroTM room preset controller (MRD6) English Ready? Application Read and retain these instructions For more information on designing, TM installing and using wireless Miro systems, and for expert technical help, call 1-800-223-4185, or visit our web site at: www.passandseymour.com/miro Use one or more wireless MiroTM room preset controllers in a room with any number of wireless MiroTM dimming or non-dim devices.
PAGE 2
press and hold Ú on any previously bound device for 2 seconds to start the procedure, verify that the newly added device LED is flashing green, indicating that it has acquired the House ID. Press and hold Ú for 2 seconds again on the same previously installed device to terminate. Room Setup 1, 3 When all the wireless MiroTM devices in the room are successfully bound to the House ID, it’s time to bind them together as a Room.
PAGE 3
Advanced Users More Scenes Press Ú and preset B simultaneously to cause the controller to record and recall scenes 5-8 Figure 6 You can increase the number of scenes in a room up to a total of 16. You will need one wireless MiroTM room preset controller for each four scenes.
PAGE 4
Cleaning Clean only using a cloth dampened with water and a little mild detergent. Use of solvents or hydrocarbon-based cleaners may cause permanent damage. Troubleshooting Problem: At house binding, not all the wireless MiroTM devices in the house are flashing green. In larger homes, some of the devices may be out of range of the initiating device. In this case, it will be necessary to add a wireless MiroTM Radio Repeater to boost radio signal range.
PAGE 5
Lifetime Warranty MiroTM is much more than lighting control! For information on MiroTM wiring devices, decorative wall plates, home networks and home automation solutions, visit our web site at www.passandseymour.com/miro The device you have purchased is warranted under normal use against defects in workmanship and materials for as long as you own the device.