User's Manual

ManualsBrandsWatt Stopper ManualsElectronicsMRD2, MRD3, MRD4, MRD5, MRD6, MRD8, MRD9

How to install and use the

wireless Miro

remote switch

(MRD8)

English

Read and retain these instructions

Français

Español

Ready?

Application

For more information on designing,

installing and using wireless Miro

systems, and for expert technical

help, visit our web site at

www.passandseymour.com/miro

Use one or more wireless Miro

remote

switches in a group with a wireless Miro

dimming or switching device, for seamless 3-

way, 4-way (or more-way!) control of a load

circuit from multiple locations.

The wireless Miro

remote switch may be

combined with the following wireless Miro

control devices:

 Incandescent Dimmer

 Universal Dimmer

 Non-dim Switch

 Plug-in Lamp Module

 Plug-in Appliance Module

Installation

Disconnect power to circuit by turning circuit

breaker OFF before installation.

Remove existing wall plate and switch.

Strip existing wires ½”

Wire the LIVE (black), NEUT (white), and

GND supply wires to the correspondingly

marked screw terminals, following the

wiring diagram in figure 1

Mount using a Miro

wall plate, following

instructions provided

Switch the circuit breaker back ON.

INSTALL IN COMPLIANCE WITH ALL

APPLICABLE CODES & STANDARDS.

Failure to follow these instructions may

cause personal injury or equipment damage.

Get Set…

Configuration

Figure 2

To prevent interference between neighboring

systems, wireless Miro

devices must

acquire a unique house ID before use. It’s

simple!

1. With all devices installed and energized,

check that every wireless Miro

device

is showing a yellow LED. If not, check

that the circuit breaker is on and that the

device is correctly installed.

2. All devices in a home must be ‘bound’ to

the same home ID. For a new wireless

Miro

installation, simultaneously press

and hold the top and bottom (Ú) of any

device paddle for 2 seconds. Its LED

flashes yellow, indicating that it has

acquired a unique House ID.

3. Check that all other wireless Miro

device LEDs are flashing green,

indicating that they have acquired the

same House ID.

4. Return to the first device, and press Ú

again for 2 seconds. All device LEDs

revert to green, indicating that house

binding is complete.

Note: if you’re adding the device to an

existing wireless Miro

installation, simply

press and hold Ú on any previously bound

device for 2 seconds to start the procedure,

verify that the newly added device LED is

flashing green, indicating that it has acquired

the House ID. Press and hold Ú for 2

seconds again on the same previously

installed device to terminate.

GND

NEUT

LIVE

Figure 1

Supply

Wire

2, 4

When you see Ú in

the instructions,

press and hold the

top and the bottom

of the device face

for 2 seconds

Summary of content (4 pages)

PAGE 1
How to install and use the wireless MiroTM remote switch (MRD8) Ready? English Read and retain these instructions Application Use one or more wireless MiroTM remote switches in a group with a wireless MiroTM dimming or switching device, for seamless 3way, 4-way (or more-way!) control of a load circuit from multiple locations.
PAGE 2
Groups Example – 2 remote switches and a dimmer make up a true 4way control circuit. Hot Dimmer Remote switch Remote switch Neutral 1, 3 2 2 Go! Use one or more wireless MiroTM remote switchs in conjunction with a wireless MiroTM dimmer or non-dim (see list in the Applications section above) to control one lighting circuit from multiple locations. When you do this, the dimmer works in exactly the same way, from any of the control locations.
PAGE 3
Cleaning Clean only using a cloth dampened with water and a little mild detergent. Use of solvents or hydrocarbon-based cleaners may cause permanent damage. Troubleshooting Problem: At house binding, not all the wireless MiroTM devices in the house are flashing green. In larger homes, some of the devices may be out of range of the initiating device. In this case, it will be necessary to add a wireless MiroTM Radio Repeater to boost radio signal range.
PAGE 4
Lifetime Warranty MiroTM is much more than lighting control! For information on MiroTM wiring devices, decorative wall plates, home networks and home automation solutions, visit our web site at www.passandseymour.com/miro The device you have purchased is warranted under normal use against defects in workmanship and materials for as long as you own the device.