User's Manual

ManualsBrandsWatt Stopper ManualsElectronicsMRP6W/MRP7W

How to install and use the

wireless Miro

plug-in

appliance module (MRP7)

English

Read and retain these instructions

Français

Español

Ready?

Load Types

For more information on designing,

installing and using wireless Miro

systems, and for expert technical

help, call 1-800-223-4185, or visit our

web site at:

www.passandseymour.com/miro

Use the wireless Miro

plug-in appliance

module to remotely control any plug-in

electrical appliance up to 800W at 120VAC.

The wireless Miro

appliance module

incorporates an electro-mechanical relay that

switches the load safely and without internal

arcing at the zero-crossing point of the AC

wave form.

Use the wireless Miro

appliance module

to switch loads such as coffee-makers,

irrigation equipment, AC motors and pumps

(up to the 800W or 1/8 hp maximum load).

The wireless Miro

appliance module

forms a valuable component in any room or

whole-house control system.

Installation

Plug the wireless Miro

plug-in appliance

module into a convenient 15amp 120V

grounded receptacle.

Plug the appliance into the grounded 15amp

outlet on the base of the lamp module.

Check that the appliance is working by

pressing the × button on the appliance

module. If the appliance does not switch

on, flip its switch to the on position, and

leave it there.

You can switch off the appliance by pressing

Ø on the appliance module.

Get Set…

Configuration

Figure 2

To prevent interference between neighboring

systems, wireless Miro

devices must

acquire a unique house ID before use. It’s

simple!

1. With all devices installed and energized,

check that every wireless Miro

device

is showing a yellow LED. If not, check

that the circuit breaker is on and that the

device is correctly installed.

2. All devices in a home must be ‘bound’ to

the same home ID. For a new wireless

Miro

installation, simultaneously press

and hold the raise and lower buttons or

paddle (Ú) of any device for 2 seconds.

Its LED flashes yellow, indicating that it

has acquired a unique House ID.

3. Check that all other wireless Miro

device LEDs are flashing green,

indicating that they have acquired the

same House ID.

4. Return to the first device, and press Ú

again for 2 seconds. All device LEDs

revert to green, indicating that house

binding is complete.

Note: if you’re adding the device to an

existing wireless Miro

installation, simply

press and hold Ú on any previously bound

device for 2 seconds to start the procedure,

verify that the newly added device LED is

flashing green, indicating that it has acquired

the House ID. Press and hold Ú for 2

seconds again on the same previously

installed device to terminate.

Figure 1

Status LED

2, 4

Note: when you

see Ú in the

instructions, press

the up (×) and

down (Ø) arrow

buttons at the same

time

Grounded

15amp outlet

Summary of content (4 pages)

PAGE 1
How to install and use the wireless MiroTM plug-in appliance module (MRP7) Read and retain these instructions Ready? Load Types English Use the wireless MiroTM plug-in appliance module to remotely control any plug-in electrical appliance up to 800W at 120VAC. For more information on designing, installing and using wireless MiroTM systems, and for expert technical help, call 1-800-223-4185, or visit our web site at: www.passandseymour.
PAGE 2
Go! Use! 1 2 IMPORTANT – Air Gap Isolation: to isolate the load for maintenance, unplug the appliance fixture from the appliance module outlet. Figure 3 Advanced Operation 1, 3 wireless MiroTM remote switch mounted at a conventional light switch location 2 MiroTM wireless plug-in apliance module, located anywhere Now, the appliance module is controlled from the wall switch location, just like a permanently installed switch. Figure 4 1. Press × momentarily to switch the circuit ON 2.
PAGE 3
Cleaning Clean only using a cloth dampened with water and a little mild detergent. Use of solvents or hydrocarbon-based cleaners may cause permanent damage. Troubleshooting Problem: At house binding, not all the wireless MiroTM devices in the house are flashing green. In larger homes, some of the devices may be out of range of the initiating device. In this case, it will be necessary to add a wireless MiroTM Radio Repeater to boost radio signal range.
PAGE 4
Lifetime Warranty MiroTM is much more than lighting control! For information on MiroTM wiring devices, decorative wall plates, home networks and home automation solutions, visit our web site at www.passandseymour.com/miro The device you have purchased is warranted under normal use against defects in workmanship and materials for as long as you own the device.