IPPAN4 Installation Manual Version 1.
CONTENTS 1.0 OVERVIEW 2.0 IPPAN4 MODULE 3.0 2.1 SPECIFICATIONS 2.2 PIN SIGNALS 2.3 ANTENNAS 2.4 OPERATING CHANNELS MODES OF OPERATION 4.0 INSTALLATION 4.1 DESIGN GUIDELINES 4.2 END USER GUIDELINES 5.0 AGENCY CERTIFICATIONS 6.0 OEM LABELING REQUIREMENTS 7.
1.0 OVERVIEW Thank you for choosing the IPPAN4 module by Wattstopper. This manual will guide you through the process of installing the module. IPPAN4 embeds wireless IPv6-based communication into each Wattstopper or host device, and uses wireless mesh networking technology to connect to the internet. Each IPPAN4 module has a unique IPv6 address and “smart” functionality which enables wireless data gathering, communication, and control of the host device.
2.1 SPECIFICATIONS Specification IPPAN4 Performance Tuning Range Internally calibrated for the selected IEEE channel Data Rate 250kb/s Max 802.15.4 Radio Output Power 16.4dBm Max BLE Radio Output Power 2.0dBm 802.15.4 Receiver Sensitivity -101dBm BLE Receiver Sensitivity -96 dBm Power Requirements VCC 2.0 - 3.3Vdc, 0.3A General Dimensions 2.8 x 15 x 26 mm (H x W x D) Operating Temperature -30° C to + 60° C Humidity 90% RH (max), non-condensing Agency Approval United States (FCC, 15.
2.2 PIN SIGNAL FIG 3.
11 IN_BUS_MISO IN BUS SPI Master Input → Slave Output 12 CRYPTO_IC_CLK Ext I2C Clock 13 GND Ground 14 IN_BUS_MOSI IN BUS SPI Master Output → Slave Input 15 GPIO_2 General Purpose Input/Output 16 IN_SCLK IN BUS SPI SCLK 17 EXT_SPI_MOSI Ext SPI Master Output → Slave Input 18 GPIO_0 General Purpose Input/Output 19 EXT_SPI_CLK Ext SPI Clock 20 Spare (HI f) General Purpose Input/Output (High Frequency) 21 AIN3 Analog to Digital Converter or Pulse Width Modulation or General Purpos
2.3 Antennas The IPPAN4 module can have two antennas. The ceramic antenna has a gain less than 0.5dBi, and the external antenna can use different antenna base on different Wattstopper product . but the gain not higher than 4.0dBi. 2.4 Operating Channels IPPAN4 provides a wide range of channels. IEEE 802.15.4 Operating Channels Operating Frequency [GHz] 11 2.405 12 2.410 13 2.415 14 2.420 15 2.425 16 2.430 17 2.435 18 2.440 19 2.445 20 2.450 21 2.455 22 2.460 23 2.465 24 2.
3.0 Modes of Operation The final use and application of IPPAN4 is dependent on the firmware pre-installed at the factory. However, all applications have common modes of operations that can be summarized as follows for both the IEEE® 802.15.4 and BLE radios: NOTE: IEEE® 802.15.4 can be used only when BLE is not in use. Idle Mode IPPAN4 enters idle mode of operation whenever the device is not in transmit, or receive mode, or when there is no data to process.
4.0 INSTALLATION IPPAN4 will come pre-programmed from the manufacturer, and in many cases pre-installed in a device. If you have elected to install IPPAN4 in house, it is important to understand how to handle, install, and use properly. 4.1 DESIGN GUIDELINES ● The IPPAN4 Module is designed either to be surface mounted. ● Standard electrostatic discharge precautions should be taken when handling the module.
4.2 END USER GUIDELINES The module is designed to be used in fixed locations. If the end user experiences communication problems it is recommended to move the transceivers closer to one another or purchase a repeater. Objects including, but not limited to, steel reinforced walls, metal electrical boxes, water, and snow may degrade the working distance between transceivers, and should be avoided.
5.0 AGENCY CERTIFICATIONS Operating Requirements and Conditions The design of IPPAN4 complies with FCC and IC safety levels of radio frequency (RF) exposure for Mobile devices. Mobile Device RF Exposure Statement RF Exposure - This device is only authorized for use in a mobile application. At least 20 cm of separation distance between the IPPAN4 device and the user's body must be maintained at all times.
5.0 Exigences et conditions de fonctionnement: La conception de IPPAN4 est conforme aux limites d'exposition aux Frequences Radio définies par les normes IC et FCC pour les appareils mobiles. Déclaration d'exposition aux fréquences radio d'appareil mobile Exposition fréquences radio - Cet appareil est seulement conçu pour usage mobile. Au moins 20 cm de séparation doit être maintenue à tout instant entre l'appareil IPPAN4 et l'utilisateur.
6.0 OEM Labeling Requirements WARNING! The Original Equipment Manufacturer (OEM) must ensure that FCC/IC labeling requirements are met. This includes a clearly visible label on the outside of the final product enclosure that displays the contents shown below. FCC: IC: Contains FCC ID: Q4B-P4 Contains IC: 21161-P4 Exigences en matière d'étiquetage OEM : ATTENTION! Le fabricant d'équipement d'origine (OEM) doit veiller à ce que les exigences en matière d'étiquetage de la FCC / IC soient respectées.
7.0 END USER LICENSE AGREEMENT 1. USER NOTICE Please read this End User Software License Agreement (“License Agreement”) carefully before using your Wattstopper product. By installing and registering an Wattstopper device you hereby agree with the terms of this License Agreement. If you do not agree with the terms of this License Agreement, do not use the Wattstopper Product and Wattstopper Software. 2.
5. DISCLAIMER OF WARRANTIES TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, WATTSTOPPER PROVIDES THE WATTSTOPPER SOFTWARE “AS IS” AND “AS AVAILABLE” WITH ALL FAULTS AND WITHOUT WARRANTY OF ANY KIND.
9. GOVERNMENT END USERS The Wattstopper Software is classified as “commercial computer software” and the Documentation is classified as “commercial software documentation” or “commercial items.” Any use, modification, reproduction, release, performance, display or disclosure of the Wattstopper Software or Documentation shall be governed solely by the terms of this License Agreement and shall be prohibited except to the extent expressly permitted. 10.
