IPPAN3-B Installation Manual Version 1.
CONTENTS 1.0 OVERVIEW 2.0 IPPAN3-B MODULE 2.1 SPECIFICATIONS 2.2 ANTENNAS 2.3 OPERATING CHANNELS 3.0 MODES OF OPERATION 4.0 INSTALLATION 4.1 DESIGN GUIDELINES 4.2 END USER GUIDELINES 5.0 AGENCY CERTIFICATIONS 6.0 OEM LABELING REQUIREMENTS 7.
1.0 OVERVIEW Thank you for choosing the IPPAN3-B module by Wattstopper. This manual will guide you through the process of installing the module. IPPAN3-B embeds wireless IPv6-based communication into each Wattstopper or host device, and uses wireless mesh networking technology to connect to the internet. Each IPPAN3-B module has a unique IPv6 address and “smart” functionality which enables wireless data gathering, communication, and control of the host device.
2.1 SPECIFICATIONS Specification IPPAN3-B Performance Tuning Range Internally calibrated for the selected IEEE channel Data Rate 250kb/s Max 802.15.4 Radio Output Power 16.4dBm Max BLE Radio Output Power 2.0dBm 802.15.4 Receiver Sensitivity -101dBm BLE Receiver Sensitivity -96 dBm Power Requirements VCC 2.0 - 3.3Vdc, 0.3A General Dimensions 5.7 x 24.
FIG 3.
17 AMP_BYPASS/NFC2 Front End Bypass or Near-Field Communication 18 CTX General Purpose Input/Output (Low Frequency) 19 GPIO_6 General Purpose Input/Output 20 SWDCLK SWD Clock 21 SWDIO SWD Data 22 GPIO_2 General Purpose Input/Output 23 GPIO_5 General Purpose Input/Output 24 EXT_SPI_CS SPI CS or General Purpose Input/Output 25 I2C_DATA I2C Data 26 I2C_CLK I2C Clock 27 GPIO-3 General Purpose Input/Output 28 GPIO_1 General Purpose Input/Output 29 AtoD PWM GPIO Analog to Dig
2.2 Antennas The IPPAN3-B module can have two antennas. ANT1 antenna use ceramic antenna , the gain less than 0.5dBi, and the ANT2 antenna can use Dipole antenna and other wire antennas, but the gain can not higher than 2.0dBi. 2.3 Operating Channels IPPAN3-B provides a wide range of channels. IEEE 802.15.4 Operating Channels Operating Frequency [GHz] 11 2.405 12 2.410 13 2.415 14 2.420 15 2.425 16 2.430 17 2.435 18 2.440 19 2.445 20 2.450 21 2.455 22 2.460 23 2.465 24 2.
3.0 Modes of Operation The final use and application of IPPAN3-B is dependent on the firmware pre-installed at the factory. However, all applications have common modes of operations that can be summarized as follows for both the IEEE® 802.15.4 and BLE radios: NOTE: IEEE® 802.15.4 can be used only when BLE is not in use. Idle Mode IPPAN3-B enters idle mode of operation whenever the device is not in transmit, or receive mode, or when there is no data to process.
4.0 INSTALLATION IPPAN3-B will come pre-programmed from the manufacturer, and in many cases pre-installed in a device. If you have elected to install IPPAN3-B in house, it is important to understand how to handle, install, and use properly. 4.1 DESIGN GUIDELINES ● The IPPAN3-B Module is designed either to be surface mounted.
4.2 END USER GUIDELINES The module is designed to be used in fixed locations. If the end user experiences communication problems it is recommended to move the transceivers closer to one another or purchase a repeater. Objects including, but not limited to, steel reinforced walls, metal electrical boxes, water, and snow may degrade the working distance between transceivers, and should be avoided.
Operating Requirements and Conditions This device complies with Part 15, Subpart C, Section 15.247 of the FCC Rules,This device IPPAN3-B should not collocate with other radio. Mobile Device RF Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Exigences et conditions de fonctionnement: La conception de IPPAN3-B est conforme aux limites d'exposition aux Frequences Radio définies par les normes IC et FCC pour les appareils mobiles. Déclaration d'exposition aux fréquences radio d'appareil mobile Cet équipement est conforme aux limites d’exposition aux radiations de la IC définies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps.
6.0 OEM Labeling Requirements WARNING! The Original Equipment Manufacturer (OEM) must ensure that FCC/IC labeling requirements are met. This includes a clearly visible label on the outside of the final product enclosure that displays the contents shown below. FCC: Contains FCC ID: Q4B-P3B IC: Contains IC: 21161-P3B Exigences en matière d'étiquetage OEM : ATTENTION! Le fabricant d'équipement d'origine (OEM) doit veiller à ce que les exigences en matière d'étiquetage de la FCC / IC soient respectées.
7.0 END USER LICENSE AGREEMENT 1. USER NOTICE Please read this End User Software License Agreement (“License Agreement”) carefully before using your Wattstopper product. By installing and registering an Wattstopper device you hereby agree with the terms of this License Agreement. If you do not agree with the terms of this License Agreement, do not use the Wattstopper Product and Wattstopper Software. 2.
5. DISCLAIMER OF WARRANTIES TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, WATTSTOPPER PROVIDES THE WATTSTOPPER SOFTWARE “AS IS” AND “AS AVAILABLE” WITH ALL FAULTS AND WITHOUT WARRANTY OF ANY KIND.
9. GOVERNMENT END USERS The Wattstopper Software is classified as “commercial computer software” and the Documentation is classified as “commercial software documentation” or “commercial items.” Any use, modification, reproduction, release, performance, display or disclosure of the Wattstopper Software or Documentation shall be governed solely by the terms of this License Agreement and shall be prohibited except to the extent expressly permitted. 10.
