User's Manual

Status LED Indicator
The LED can display one of three co lo rs: green, ye l l ow (amber, a
combination of red and green), or red. The co lor can be co n stant, or
can flash at one of three ra tes to further distinguish re p o r te d
conditions. To determine the flash ra te, count the number of fla s h e s
in 5 seco n d s :
5 fla s h e s. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Hz
10 fla s h e s. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Hz
15 fla s h e s. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Hz
MRDS10 LED Indications are as fo l l ow s :
C o l o r B e h a v i o r M e a n i n g
n o n e O f f D e v i c e is not powe r ed or is in “sle e p ”
m o d e .
G r e e n On, not fla s h i n g D e v i c e is powe red, has a house ID,
o p e rating normally.
G r e e n Flashing @ 2 Hz During binding, dev i c e is excluded, but
can be added.
Ye l l ow On, not fla s h i n g D ev i ce does not have a house ID.
Ye l l ow Flashing @ 2 Hz D ev i c e is part of a binding pro ce s s, either
G r oup or Room. Binding was sta r ted by
some other dev i ce and must be sto p p e d
on the other dev i ce .
Ye l l ow Flashing @ 3 Hz D ev i c e is the master of a binding
p r o ce s s. Binding was sta r ted on this
d ev i ce and must stop on this dev i ce .
R e d Flashing @ 2 Hz D e v i c e has enco u n te red an erro r. An
i n valid command was atte m p te d .
Caution: Battery Vo l tage is Low ~ 10s
every 1-2 minute s
R e d Flashing 3 Hz Shutting down To u c h s c r een due to low
b a t t ery co n d i t i o n
APPLICATION ASSISTANCE
The wire le s s network may co n tain a variety of wire l e s s dev i c e s .
I n str uctions for installation, binding operations, and use are
included with the re l evant wire l e s s dev i c es. Application support
i n f ormation and installation guides for Watt Sto p p e r / L e g ra n d
w i r e le ss network dev i c es are ava i l a b l e at www. w a t t s to p p e r. c o m .
SPECIFICATIONS
UL and cUL Liste d
Power Supply / C h a r ger (MRDP10)
Input Vo l ta g e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2 0 VAC, 0.15A, 60 Hz
Output Vo l t a g e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8VDC, 600mA
To u c h s c r een (MRDS10)
Input (charging) Vo l t a g e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8VDC, 600 mA
DESCRIPTION
The MRDS10 To u c h s c r een is a Top Dog™ wire le s s network House,
Room and Group level co n t r o l le r. It has a 2-co lor LCD touch panel
d i s p l a y.
The To u c h s c r een can be opera ted with power supplied by the
MRDP10 wall-mount charger, the optional MRDC10 ta b le - to p
c h a rger, or it can be te m p o ra r i ly re m o ved from the power supply to
be used as a porta b le hand-held dev i c e .
Top Dog™ Wireless Communication
Watt Stopper wire l e ss dev i c es use radio signals to co m m u n i ca te with
each other to co n t rol lighting and other types of electric loads in
s e le c ted areas. These wire le s s dev i c es use the 900MHz band fo r
high-speed co n t rol co m m u n i cation. Using the Watt Sto p p e r ’s ow n
“ f r e q u e n c y - a g i le” Top Dog™ te c h n o logy, these wire l e ss dev i c es avo i d
i n t e r fe re n ce with other 900MHz dev i c es, such as co r d l e ss phones
and baby monito rs .
OPERATION
The MRDS10 To u c h s c r e e n is a house level scene co n t ro l l e r.
The MRDP10 is included with the MRDS10 package. It is a wall-
m o u n t ed power supply and battery charger for the To u c h s c r een. The
To u c h s c r een can be used while attached to the MRDP10, or it can be
te m p o ra r i l y re m oved from the MRDP10 and used as a porta b l e
handheld dev i ce. The To u c h s c r een should be returned to a MRDP10
or MRDC10 power supply to re c h a rge its batte r i e s .
Human Interface
The primary human inte r fa ce on the MRDS10 is the To u c h s c re e n .
The menus and co n t rol functions are acce s sed by
touching the labels and icons on the screen. The
To u c h s c r een has a help system built into each page.
To acce ss help and information about a particular
page, pre s s the question mark button at the top of any
p a g e .
The MRDS10 also uses a multi-co lor LED (gre e n / a m b e r / red) to
i n d i c a te dev i ce status. Dire c t ly below the LED there is a single push-
b u t t on. Momenta r i ly pre ss this button to wake up the dev i c e when in
p ower save mode. This button also acts as a software reset (re b o o t )
function when held for a period of 10 seconds. When this is done the
fa c tory default co n t ra st and brightness settings are re s to red. No
other setup information is alte r ed.
To reset the unit to a fa c to r y
d e f ault sta te, the user must use
the To u c h s c reen to go into the
setup menu and perform this
function in the Lock/Reset page .
Power Fail Memory
A f ter a power fa i l u re, all wire l e ss dev i c es auto m a t i c a l l y return to the
sta te that they we re in immediate ly prior to lo s s of powe r. All
co n fi g u r ation and scene co n t rol information is pre s e r ved.
M R D S 1 0
W i re l e s s To u c h s c reen Contro l l er with
wall-mount power supply & charg e r