Installation Instructions

ManualsBrandsWatt Stopper ManualsElectronicsFIXTURE INTEGRATED SENSOR - PIR AND DAYLIGHT SENSING

Wattstopper

DLM Integrated Fixture Sensor and Controller, Occupancy, Daylight

Harvesting, and IPv6/Bluetooth

Low Energy Technology

Installation Instructions • Instructions d’Installation • Instrucciones de Instalación

No: 30769 – 07/20 rev. 1

Catalog Numbers • Les Numéros de Catalogue • Los Números de Catálogo: LMFS-601-W

Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China

SPECIFICATIONS

Input Voltage ..................................................................................................12–20V

Power Consumption from DALI Bus ................................................................. 16mA

Power Supply ......Wattstopper Fixture Interface (LMFI-111)/ DALI v1.0 compliant driver

Wiring ...................................................................................................... 18–20 AWG

Terminal Connection ....................................................................................DA+, DA-

Connection DLM Network .............................Wireless via LMFS-601 fixture sensors

Wireless Radio .... Single, Concurrent 802.15.4 and Bluetooth Low Energy, 2.4 GHz

Wireless Communication:

IPv6 Mesh (6LoWPAN) Range ............................................................ up to 60ft

Bluetooth Low Energy Range ............................................................. up to 30ft

Wireless Encryption ......................................................... AES-128 bit symmetric key

Operating Temperature ............................................................... 32–122°F (0–50°C)

Relative Humidity ............................................................ 0 to 90% (non-condensing)

Enclosure ............................................................................................................IK05

Compatible Border Router.....................................................Wattstopper LMBR-650

BACnet IPv6 capable

DESCRIPTION

The LMFS-601-W is a wireless fixture sensor and controller that is compatible with all Wattstopper IPv6/Bluetooth low energy

technology wireless DLM devices. The LMFS-601-W is a PIR occupancy sensor and a closed loop photo sensor. It measures both

motion and daylight contribution in order to automatically switch or dim lighting.

The LMFS-601-W can also be joined to a multi-room mesh network by adding an LMBR-650 border router. The integrated fixture sensor

can join an LMBR-650 network using the wireless DLM Config App or LMCS v4.7 and later.

Installation shall be in accordance with all applicable

regulations, local and NEC codes. Wire connections shall

be rated suitable for the wire size employed.

For Class 2 DLM devices and device wiring: To be

connected to a Class 2 power source only. Do not reclassify

and install as Class 1, or Power and Lighting Wiring.

INSTALLATION

• Ensure knockout and adjacent surfaces are free from burrs, oil, chemicals, debris, etc.

• Clean only with soft, damp cloth. Do not use chemical cleaners.

• Do not paint.

• LMFS-601-W should be mounted to fixture surface that is parallel to the floor in final installation.

• Do not install in direct view of the light source or reflecting surface.

• Install in a location that allows the sensor to have an unobstructed view of the area. Do not mount behind glass or clear plastic.

• Sensor not intended for hanging pendants - occupancy coverage area is reduced.

• Install away from radiated heat given off by the light source

Materials Required:

• Solid core wire (18-20 AWG)

• A DALI Driver with Integrated Self Powered DALI Link Or A Wattstopper Fixture Interface

(LMFI-111)

Summary of content (4 pages)

PAGE 1
Wattstopper ® DLM Integrated Fixture Sensor and Controller, Occupancy, Daylight Harvesting, and IPv6/Bluetooth® Low Energy Technology No: 30769 – 07/20 rev.
PAGE 2
Installation The LMFS-601-W comes equipped with a carrier a sleeve and collar in which it snaps into during installation into the fixture. The carrier sleeve fits into industry standard 1/2” knockouts and/or a 7/8” hole. The carrier sleeve is intended to be mounted into lighting fixtures or directly into ceiling tiles. 1. To install the carrier sleeve into the desired knockout, apply pressure and turn counterclockwise until the carrier sleeve is flush with the mounting application. 2.
PAGE 3
LMFS-601-W STARTUP AND COMMISSIONING NOTE: When the luminaire and LMFS-601-W are powered, the fixture turns ON and PIR Sensor Light Sensor reaches its full output. The sensor module then cycles through the entire dimming range starting from 100% output level to OFF* two times. After the power cycle, the light level will return to 100%. This sequence of operation will take place after Antenna every power cycle until the sensor is commissioned using the DLM Config App.
PAGE 4
LMFS-601-W DEFAULT SETTINGS Occupancy Behavior – Auto On to 80% of maximum light level. All other Groups outside of occupancy sensed Group power ON to 20% of maximum light level. Time Delay – 20 min Time Delay Dim Level – 20% Max Light output High End Trim Preset – 80% Low End Trim – 1% Daylight – Disabled by Default Daylight Function – Closed Loop FCC Notice: This device complies with Part 15 of the FCC Rules.