User's Manual

ManualsBrandsWatt Stopper ManualsElectronicsWireless Universal Dimmer

ADVANCED OPERATION

Groups

Use a Wireless Miro universal dimmer in conjunction with one or more Miro

DRD8 Wireless Multilocation Controllers to control one lighting circuit from

multiple locations. Binding the DRD40 and DRD8 devices together in the same

Group enables them to work in exactly the same way, from any of the control

locations.

You can include other Miro wireless devices in the Group. Just remember that

all devices in the Group operate when one member operates. If you increase

the brightness on one circuit in the Group, all circuits will increase brightness.

Set the House ID (see Set House ID) before setting up Groups.

Creating a New Group

1. Go to any device that you want to include in the Group. Press . The device

LED ﬂ ashes yellow, and all other devices in the house ﬂ ash green.

You now have 5 minutes to complete this process.

2. To include or exclude a device in the Group press

on the device until the

LED changes color. Yellow ﬂ ashing LED = Included in the Group

Green ﬂ ashing LED = NOT included in the Group

If you get to a device and it is NOT ﬂ ashing, the 5 minute binding process

timer may have expired. Go back to step 1 and repeat.

3. Return to the device used in step 1 and press

to terminate Group binding.

All LEDs revert to solid green. Now, all the devices in the Group control their

load circuit in exactly the same manner.

Adding a Dimmer to a Group in an Existing System

1. Go to a device that is in the Group where you want to add the dimmer.

Press . The device LED and all members of the Group flash yellow.

The new dimmer flashes green.

2. Press

on the new dimmer until its LED flashes yellow.

3. Return to the device used in step 1 and press

. All LEDs are solid green.

Scene Control

The Miro Wireless Universal Dimmer may be easily incorporated into room

and whole house preset scenes. The Miro Installation Guide provides more

information about conﬁ guring scenes and presets.

Instructions for installation and use are included with the relevant Miro

wireless room and whole house control devices. Application support

information and the Miro Installation Guide are available online.

ii_DRD40_10346r2 090209.indd 1ii_DRD40_10346r2 090209.indd 1 2/10/2009 3:04:31 PM2/10/2009 3:04:31 PM

Summary of content (9 pages)

PAGE 1
ADVANCED OPERATION Groups Use a Wireless Miro universal dimmer in conjunction with one or more Miro DRD8 Wireless Multilocation Controllers to control one lighting circuit from multiple locations. Binding the DRD40 and DRD8 devices together in the same Group enables them to work in exactly the same way, from any of the control locations. You can include other Miro wireless devices in the Group. Just remember that all devices in the Group operate when one member operates.
PAGE 2
CLEANING Clean using a cloth dampened only with water and a little mild detergent. Use of solvents or hydrocarbon-based cleaners may cause permanent damage. TROUBLESHOOTING During Set House ID, the LED is not flashing on some wireless Miro devices. • If LED is solid green before initiating House ID binding: The device already has another House ID. Reset it to the factory default so that it can be bound to the desired House ID. Resetting to factory defaults is described in the “I need to start over” issue.
PAGE 3
FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 4
Specifications Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120VAC, 60Hz Operating Temperature . . . . . . . . 32ºF to 104ºF (0ºC to 40ºC) Maximum Load Rating . . . . . . . . . . . . . . . . . . . . . . . . . . 1000W Minimum Load Required . . . . . . . . . . . . . . . . . . . . . . . . . . 25W Load Type Compatibility . . . . . . . . . . . . . . . . . .
PAGE 5
UNIT DESCRIPTION The Miro Decorator DRD40 Wireless Universal Dimmer provides dimming of various 120V lighting load types with a minimum load of 25W. Do not mix different load types on the same dimmer. Do not use with ﬂuorescent ﬁxtures other than those listed in the table below. When more than one dimmer is installed in a multi-gang box, it is necessary to reduce the maximum load on each dimmer as shown in the table below.
PAGE 6
CAUTION TURN THE POWER OFF AT THE CIRCUIT BREAKER BEFORE INSTALLING THE DIMMER. INSTALLATION For ease of installation, manufacturer recommends use of a deep wall box. 1. Disconnect power to circuit by turning circuit breaker OFF before installation. 2. Remove existing wall plate and switch. 3. Strip existing wires 1/2” (12.7mm). 4. Connect the LINE, NEUTRAL, LOAD and GROUND supply wires to the DRD40 ﬂying leads, according to the wiring diagram below. 5. Attach the wall plate. 6.
PAGE 7
SET HOUSE ID All Miro wireless devices installed in the same home must acquire the same unique House ID before use. This process is known as house binding. Each Miro wireless device is bound to all other Miro wireless devices in the house. New Installation 1. With all devices installed and energized, make sure that every Miro wireless device LED is yellow. If any LED is off, be sure the circuit breaker is on and the device is correctly installed. When you see 2.
PAGE 8
3. Press and hold until the LED changes to green (about 2 seconds). 4. To reconﬁgure the dimmer to control non-ﬂuorescent loads, repeat the above steps 1-3, but press the bottom of the device paddle rather than in step 2; the LED brieﬂy ﬂashes green to conﬁrm the cancellation of ﬂuorescent operation.
PAGE 9
REV DESCRIPTION INT: REV. DATE APPROVED 1 ECO# C02581 MJS 10/31/08 CG 2 ECO# C03057 RD TITLE BOX PAGE ONLY. DO NOT MAKE FILM • DO NOT PRINT • Print: 2-sides • Ink Color: Black • Paper: White 80g/m sq NOT coated, prefer recycled stock • Final trim size: 16” (Wide) x 6” (High). • Four (4) fold. • Final folded size: 4” (Wide) x 6” (High). 4-FOLD IF YOU HAVE ANY QUESTIONS REGARDING SPECIFICATIONS OR REQUIRE ADDITIONAL FILE FORMATTING, PLEASE CONTACT Mary Jo Sowinski.