IMPORTANT INSTRUCTIONS & OPERATING MANUAL Amazon – Decorative Electric Fireplace with On Screen Display Item No: P50-1/0345 Read these instructions carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and / or property damage. Retain instructions for future reference.
GENERAL SAFETY INFORMATION When using this fireplace, basic precautions should always be taken to reduce the risk of fire, electric shock and injury to persons, including the following: CAUTION – Due to the high temperature, keep electrical cords, drapery and other furnishings at least 3 feet from the front, side and rear of the fireplace. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23.
24. Faulty wall outlet connections may cause the wall outlet to overheat. Be sure that the fireplace plug properly fits into the outlet before each use. During use, make sure the fireplace plug does not overheat. If necessary, have a qualified electrician check and / or replace the wall outlet. 25. Always plug the Fireplace directly into a wall outlet/receptacle. Never use with an extension cord or re-locatable power tap (outlet/power strip). 26.
• • • • • • • • • Automatically adjusts power to match the set temperature Built-in Timer (0.5 hours to 8 hours) Built-in overheat protection (auto safety shut-o-) Built-in child safety lock On-screen Display shows temperature, heat mode, flame mode, Flame brightness, timer & child lock Heat Resistant Tempered Glass Panel Remote Control Included Wall Mount & Screws Included Product Dimensions: 48’’ (w) x 5.
Decorative Crystals Wall plug (4pcs) Screw 1 (4pcs) Screw 2 (4pcs) Note: Tools Required (not included) Drill Phillips screwdriver Helpful Tips before Installation • • • • • • • • • • Please retain all packaging until you have checked and counted all the parts and other package contents. The package contains small apparatus which should be kept away from young children and infants. We suggest that you move all the smaller parts into a container to reduce the risk of losing them.
• Please be careful when drilling holes. Identifying Mounting Location • • • • • • • • When choosing a location for your electric Fireplace, ensure that the general instructions are followed. This Fireplace must be mounted on a flat wall. Ideally, install the Fireplace directly on a brick wall, masonry surface or the internal wooden frame of a plasterboard wall.
Hardware Wall Mount (1PC) Decorative Crystals Wall plug (4pcs) Screw 1 (4pcs) Screw 2 (4pcs) A B C D E Step 1 – Remove Wall Mount (A) from back of Fireplace by removing the two screws (E) at the top of the fireplace.
Step 2 – Install wall plugs (C) into wall. 1. 2. 3. 4. Drill 4 holes [0.3” (8mm) diameter, 0.15” (4mm) deep] on the wall. Insert wall plugs (C) into the drilled holes. Please refer to the diagram for the locations of holes. Both top holes should be located at least 16.5” (420mm) away from the ceiling. Step 3 – Attach Wall Mount (A) into wall. 1. Holding the Wall Mount (A) against the drilled holes, insert screws (D) through the second & fifth holes on the upper and lower Wall Mount. 2.
Step 4 – Hang the Fireplace onto the Wall Mount. 1. Check to make sure the Wall Mount (A) is securely attached to the wall. 2. Hang the Fireplace on the hooks at the bottom of the Wall Mount (A) and push the Fireplace into the Wall Mount (A). 3. Re-fasten both the screws (E) that were removed during Step 1. 4. Check that the top of the Fireplace is at least 400 mm from the ceiling.
Step 5 - Place the decorative crystals on the front opening of the Fireplace. 1. Ensure the crystals are spread evenly in the Fireplace opening. 2. Check to make sure the crystal bed is securely in place.
Step 6 - Install the glass panel. 1. Make sure the glass panel is free from debris and dirt. 2. Hold the panel securely and hang it onto the Fireplace hooks, located on both sides.
3. The panel should be secured on all four hooks on the Fireplace. 4. Check to make sure the panel is held securely in place. Step 7 – Secure the glass panel onto the Fireplace. 1. Once you’ve mounted the glass panel onto the fireplace, locate the holes on both left and right of the fireplace and insert screw (E) in each of the holes, through the hook, into the Fireplace.
2. Tighten screw to pass it through the hook, on both sides. 3. Ensure the glass panel is secure. Note: Tighten up the screw carefully, to avoid damage to the glass panel. REMARK: This Fireplace uses 120 volts.
INSTRUCTIONS FOR USE When a function is changed from the control panel or remote control, there will be a corresponding indicator displayed on the On-screen Display. The indicator shows the function changed and the level selected. When the function is turned off, the corresponding indicator will turn off.
Replacing the remote control batteries When the remote control stops operating or its range seems reduced, it is time to replace the batteries with new ones. 1. On the back of the remote control, press and slide the battery cover open and remove the old batteries. 2. Replace with two AAA batteries (not included), as per the indicated polarity. 3. Replace the battery compartment cover. Note: Batteries should be removed if the product is to be left unused for a long time. Do not mix old and new batteries.
ECO Press the ECO button when the heater is on, to run the heater in a reduced wattage range. NOTE: Hold the ECO button for 3 seconds to disable any Fireplace functions. BOOST To quickly heat up a cold room/space, press the BOOST button to run the heater at maximum power. Press the BOOST button repeatedly to cycle through the following Boost settings: 5 minutes, 10 min, 15 min, 20 min, 25 min, 30 min and off. TIMER This function turns off the fireplace after the selected duration, automatically.
Problem Possible cause Corrective action Display shows “E1”. Auto shut off due to overheat has been activated. Inspect the Fireplace and check that the air inlets and outlets are not blocked as this may cause overheating. Unplug the Fireplace for 10 minutes and allow it to cool down. Plug it back in and turn it on; This is will reset the fireplace. Check the Fireplace for signs of overheating. If the problem persists discontinue use of the Fireplace and contact customer service. Display shows “E2”.
malfunction. Loud noise from the Fireplace. The air inlets are dirty or obstructed. Check the air inlets for obstructions or dust build up. The blower/Fireplace assembly is defective. Contact Customer Service for troubleshooting. If this doesn’t fix the problem, contact the retailer you bought the product from, for replacement.