Professional Cotton candy machine CC150 For your safety and continued enjoyment of this product, always read the instruction book carefully before using.
TABLE OF CONTENTS Important Safeguards................................................................... 2-4 Parts................................................................................................ 5 Assembly......................................................................................... 6 Operating Instructions......................................................................7 Making a Paper Cone.......................................................................8 Recipes.....
12. Always turn the appliance off before assembling or cleaning. 13. Turn appliance to OFF position before disconnecting power plug from wall outlet. 14. The motor base must be placed on a level surface to work efficiently. 15. Do not use appliance for other than intended use. 16. Do not operate any appliance with a damaged cord or plug or after the appliance is malfunctioned or has been damaged in any manner.
26. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way. Special cord set instructions A short power-supply cord is provided to reduce the risks resulting from becoming entangled in or tripping over a longer cord.
parts: A. Splashguard B. Motor Base C. Floss Head D. Measuring Scoop E. Plastic Cone F. Bowl G. Cone Holder A. C. E. G. F. G. B. D.
Assembly: STEP 1 Insert the splashguard onto the bowl (ensure all clips on the cover are fully inserted into the holes on the bowl). STEP 2 Insert the bowl and splashguard on the motor base. Make sure the bowl is pushed all the way down to meet the base, then turn clockwise to lock the bowl on the motor base. STEP 3 Insert the floss head on the motor base; ensure the shaft of the container is locked by the perpendicular shaft on the motor axis.
Operating Instructions 1. Set the motor base on a stable and level surface. 2. Connect plug to a power source. 3. Make sure floss head is in position. 4. Switch on the cotton candy machine to preheat 5 minutes. NOTE: It is very important that you preheat the cotton candy maker the full 5 minutes. 5. Switch off the cotton candy machine. Add 1 scoop of sugar mixture into the floss head. CAUTION: Floss head will be extremely hot. Never touch floss head while unit is on.
Making A Paper Cone 1. Place a standard sheet of 8½" x 11" paper on a flat surface. 2. L ay the plastic cone supplied with the unit on the 11" side of the paper and begin rolling the plastic cone until you reach the other side of the paper. 3. W ith the paper totally wrapped around the plastic cone, take a piece of tape and tape the loose paper edge down. 5. Finished paper cone. 4.
Easy cotton candy recipe 6 scoops pure cane sugar (for a fuller cone of cotton candy, we recommend using pure organic cane sugar) 1–2 drops red food coloring 1–2 drops pure vanilla extract Mix sugar, food coloring and vanilla extract thoroughly before adding to the floss head. Use one scoop of mixture per batch. NOTE: You may substitute the vanilla extract with your favorite extract flavoring.
hard candy cotton candy recipe rush up hard candy in a food processor; add to floss head. C Use one scoop of mixture per batch. Recommended hard candy: NERDS® Add one scoop of Nerds® candies to floss head. FRUIT-FLAVORED LIFE SAVERS® Add two crushed fruit-flavored Life Savers® candies to floss head. NOTE: Do not use any hard candy containing dairy ingredients. Traditional cotton candy floss and paper cones can also be used with this unit and can be found online at Amazon.
Troubleshooting Problems Loud noise occurs when operating Cotton candy blowing unevenly in the bowl Reasons Solutions The bowl is not secured on the motor/heater housing, or the floss head is not secured to the motor base Reassemble or try to lock floss head tightly The machine is placed on an uneven surface Place the machine on on a flat surface Cleaning and Maintenance 1. Make sure that the power is off and the appliance is not connected to a power source. 2.
Any trademarks or service marks of third parties herein are the trademarks or service marks of their respective owners. ©2011 Waring Consumer Products 150 Milford Road East Windsor, NJ 08520 www.waringpro.
