User Manual

ManualsBrandsWanneton ManualsElectronicsTwo-way radio

一. Function Introduction.

1、Operating frequency band: GMRS (receive/transmit)

2、16 channels

3、Scan function

4、Chinese/English language annunciation

5、CTCSS, DCS standard mute

6、TOT

7、Power saving function

8、VOX voice control function

9、Low voltage warning

10、Busy lock function

二. Function Operation

Function definition of side button 2

Side button 2 is pressed and held for: Listening function, default is fixed mode.

Listening: listens for a call on the channel of your choice, if there is no signal a "rustling"

sound will be heard.

Power/volume switch control

Turn clockwise to power on the intercom, turn counterclockwise to power off the intercom

until it clicks, turn to adjust the volume of the call.

Channel selection.

Rotate the channel i.e. switch the channel, rotate in the right direction i.e. 1 - 16, rotate in the

left direction i.e. 16 - 1.

PTT button

Press the PTT button and speak into the microphone to call the other party, a red light will

indicate this. When released for reception, if there is a signal, a green light indicates that the

speaker is on.

Squelch level

The lower the squelch level set, the greater the noise level, the greater the distance you can

talk, but the weaker the reception resistance. This function is set to 5 levels by factory default, you

can set it through the "squelch level" option in the menu of the frequency writing software, the

selectable range is 0~9, where the squelch level is always on when set to 0, the higher the level the

less likely the squelch is to turn on.

Power saving function

Power saving: On: 10 seconds without any operation, automatically enters the power saving

state. (A variety of power saving methods can be selected within the frequency writing software).

Off: The intercom does not save power.

Voice-activated transmitting

VOX Voice Control allows you to transmit without pressing the PTT transmit button, using

only the sound of your voice, and automatically stops transmitting when you stop talking. The

option to turn this function on/off is available with the frequency writing software, when on.

Summary of content (4 pages)

PAGE 1
一. Function Introduction. 1、Operating frequency band: GMRS (receive/transmit) 2、16 channels 3、Scan function 4、Chinese/English language annunciation 5、CTCSS, DCS standard mute 6、TOT 7、Power saving function 8、VOX voice control function 9、Low voltage warning 10、Busy lock function 二. Function Operation Function definition of side button 2 Side button 2 is pressed and held for: Listening function, default is fixed mode.
PAGE 2
a. When your intercom is enabled with VOX voice control. When you speak into the MIC, it automatically turns on transmitting and sends out a voice. When you stop speaking, the intercom automatically stops transmitting and waits to receive. b. When you are using a headset with a microphone. To use the voice control function, you must adjust the VOX gain and set the VOX gain so that the intercom recognises the sound level.
PAGE 3
D631N D734N D632N D743N D654N D754N D662N D664N D703N D712N D723N D731N D732N D023I D071I D134I D223I D306I D411I D503I D631I D734I D025I D072I D143I D226I D311I D412I D506I D632I D743I D026I D073I D152I D243I D315I D413I D516I D654I D754I D031I D074I D155I D244I D331I D423I D532I D662I D032I D114I D156I D245I D343I D431I D546I D664I D043I D115I D162I D251I D346I D432I D565I D703I D047I D116I D165I D261I D351I D445I D606I D712I D051I D125I D172I D263I D364I D464I D612I D723I D054I D131I D1
PAGE 4
WARNING: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.