SLU-A1000-B SLU-A1000-B
SLU-A1000-B Content 1.Product Specifications .......................................................................................... 2 2.Product Picture ..................................................................................................... 3 3. System Introduction ............................................................................................ 4 3.1 System composition........................................................................................ 4 3.
SLU-A1000-B 1.Product Specifications Specification Dimension φ175mm Net working RJ45 / Wifi Interface POE, Type C, SMA, Reset IP Grade IP50 Working Temperature: -30~70℃ Working Environment Humidity:10%~90% UWB Specification Frequency Band CH2: 3993.6MHz; CH5: 6489.6MHz Speed 6.8Mbps Output Power ≤-41.3dBm/MHz Channel Support channel 2&channel 5 Protocol Standard IEEE 802.15.
SLU-A1000-B 802.11b: 1, 2,5.5,11 802.11g: 6,9,12,18,24,36,48,54 Wireless Data Rate 802.11n: MCS0~7,HT20 reach up to72.2Mbps, (Mbps) HT40 reach up to150Mbps LED #3 HT40 reach up to300Mbps (2T2R) Rx Sensitivity -98dBm (Min) TX Power 21.36dBm (Max) IEEE Standards IEEE 802.11b/g/n LED #2 2.
SLU-A1000-B 3. System Introduction 3.1 System composition The indoor location system is composed of web application platform, location engine, anchors and tags. 1. Tag The tag is the terminal of UWB location system, which is mainly responsible for periodically sending location message to the anchor and receiving setting messages from the anchor. 2. Anchor The UWB anchor is an important part of the whole location system.
SLU-A1000-B algorithm, or send some parameter configuration information to the anchor. 4. Web application platform Web application platform is an upper application based on the development of location data. Users can directly use the functions provided by the Web application, or customize the development based on the secondary development interface provided by the Web platform. 3.
SLU-A1000-B 2. One-dimensional positioning mode One-dimensional positioning mode is used to locate only one dimension in three-dimensional world, also known as “linear positioning”. When the tag enters the one-dimensional positioning area, the system can accurately locate the tag on a straight line, which is generally applied in narrow and long areas such as tunnels and corridors. 3.
SLU-A1000-B 4. Anchor selection and installation 4.1 Anchor selection To a large extend, the selection of the tag installation location determines the difficulty of debugging and the final positioning effect, so the following principles should be referred to during the selection. 1. Zero-dimensional positioning Zero-dimensional positioning is often used for smaller enclosed areas with physical boundaries and entrances. For example, a room is often used as a zero-dimensional area.
SLU-A1000-B is less than 40m (up to 80m in the especially open area) No shielding between anchors Anchors need to be installed in the front and at the end of one-dimensional area If more than two anchors are installed in the one-dimensional positioning area (for example, the length of the area is more than 40m), the anchor in the middle is located on the boundary between the two regions and can be reused by the two regions.
SLU-A1000-B For each two-dimensional positional area, at least four anchors need to be installed, respectively installed in the four corners of the area. If two positioning area are interlinked, then the anchor located on the dividing line of two cells can be reused by the two areas. Generally a complex area will also contain a one-dimensional/two-dimensional/zero-dimensional positioning, for zero dimension in the meeting room, one dimension in the corridor, two dimension in the office or the hall.
SLU-A1000-B 4.2 Anchor Installation After the location of the anchor is selected, the next step is to install the anchor. During the installation, the principles below should be followed. The anchor should be more than 30cm away from the wall, or 50cm away from the metal wall. The height of the anchor to the ground is generally between 3m and 5m The anchor must leak out, not be embedded in the ceiling and away from metal objects.
SLU-A1000-B Positioning Map Software Various map import modes and multi-dimensional display support customization and user to import map freely. Display Mode 應用場景 2D 2.
SLU-A1000-B 5. Network Setting Up In general environment, all anchors in this layer can be networked by POE switch of the access layer, and then connected to the core layer switch by means of optical fiber or network server. Depending on the selected network architecture, each anchor needs a separate network cable connected to the switch, and the other end is fixed in a pre-reserved anchor location. Note: 1. Recommended to use more than five types of network cable 2.
SLU-A1000-B 6.Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
SLU-A1000-B Notices: This product meets the technical requirements of indoor UWB system. 1. This UWB System needs to be professional installation, and we provide free technical support to install this product indoors. During debugging by software, the using zones will be strictly controlled indoors. 2. UWB positioning system includes UWB Tag, UWB Anchor and server.
