Users Manual Pen Pad RSK-T06
The R&TTE Directive We, the manufacturer (WALTOP International Corp.) hereby declare that this equipment (Bluetooth Pen Pad- Flying Pad), model RSK-T06 is in compliance with the essential requirements and other relevant provisions of Directive 1995/5/EC. FCC Caution This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions 1. This device may not cause harmful interference, and 2.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Contents The R&TTE Directive 1 FCC Caution 1 Federal Communication Commission Interference Statement 2 Introduction 4 — Hardware introduction 4 — Function introduction 5 — How to change the battery 5 — How to replace the Pen Refill 6 — Software Introduction of Bluetooth Pen Pad Manager 7 — Wireless mode 8 — Wired mode 8 — LED Indicator information 8 — USB mode 9 Important information for you to read! 10 Installation 11 — Wired mode 11 — Wireless mode 12 How to Unpairing 27 Troublesho
Introduction Thank you for purchasing this product. Bluetooth Pen Pad provides two modes of connection with a PC: Wireless mode and wired mode. Both modes provide a convenient working environment. Please note that the setup procedures are different from wired and wireless mode and these will be stressed through this manual.
— Function introduction LED Indicator Down side button Upper side button Pen clip Pen tip — How to change the battery Battery (+ -)
— How to replace the Pen Refill 1. Pull out the used pen tip with the Refill Tweezers provided. 2. Insert the Pen Refill to the pen. 3. Press firmly on a hard surface for 5 seconds till the Pen Refill is locked.
— Software Introduction of Bluetooth Pen Pad Manager • Pen (Absolute mode) – the area of the Bluetooth Pen Pad corresponds to the whole area of the screen. For example, if place your wireless pen at the top right hand corner the mouse pointer will always be at the top right of the screen. • Mouse (Relative mode) – acts like a mouse, moves in relation to where the mouse pointer currently is. For example, place your wireless pen anywhere on the pen pad.
— Wireless mode Bluetooth Pen Pad + Bluetooth Adapter on PC PS. Make sure that you have powerful batteries in the battery chart and switch the power button to on. — Wired mode Bluetooth Pen Pad + USB Cable on PC. — LED Indicator information There are two LED’s built in. One is Red and the other is Blue. Bluetooth mode: 1. When the Bluetooth Tablet is turned on, the two LED will flash once. 2. When the battery power is low, the Red LED will start to flash until the batteries are exhausted.
— USB mode 1. When the USB cable is initially connected to the Tablet, the Red LED will flash once and the Blue LED will flash continuously. 2. The Blue LED will be on when the pen is detected within the working area but will be off as soon as the pen touches the tablet.
Important information for you to read! Bluetooth Pen Pad ships with a bundled Broadcom IC Bluetooth device and WIDCOMM Bluetooth Software. We do not test with Bluetooth software from other manufactures, but in many cases, Our Bluetooth Pen Pad will work well with these third party Bluetooth software packages if their device support WIDCOMM Bluetooth Software version 5.0.1.1600. The Important factors to consider are the source of the Bluetooth software and the version of the Bluetooth software.
software and then, install the WIDCOMM Bluetooth software that shipped with the released CD in the package. Installation Please insert the CD-Rom in the package into your CD-ROM Device. The software will automatically begin. There are three parts in AUTO RUN. One is Bluetooth Pen Pad Driver, another is Bluetooth Software and the other is Application software. The following guideline is to teach you how to make Bluetooth Pen Pad work in different mode and under different OS systems.
STEP 2 Hardware installation Please plug the USB cable firmly to Bluetooth Pen Pad and to your PC. — Wireless mode You have to install Bluetooth Pen pad Driver and Bluetooth software to complete the necessary steps. Install Bluetooth Pen Pad Driver a. Click “Bluetooth Pen Pad Manager” to start installation b. Click “ Next” c. Click “Finish” Install Bluetooth software Please reference from the important information ( Page 9 ).
– data for Microsoft Bluetooth software” 1. The data will be added into Microsoft Bluetooth software automatically. 2. Please click “finish”. STEP 2 Hardware installations 3. Please plug the Bluetooth Adapter to your PC now. 4. Finding new Hardware. 5. Welcome to the Found new hardware Wizard.
6. Install the software automaticall. 7. Completing the Found New Hardware Wizard. (P.S After that, Bluetooth icon will be showed in Windows System Tray) 8. Finding new Hardware again 9.
10. Install the software automatically 11. Completing the Found NewHardware Wizard. Click “ Finish” STEP 3 Start to Pair Bluetooth Pen Pad 12. Click on the START button, the SETTINGS, and then select CONTROL PANEL. 13. In the CONTROL PANEL, you can find the BLUETOOTH DEVICE icon.
14. Double Click BLUETOOTH DEVICE icon. Then, Please click “ ADD” 15. Add Bluetooth Device Wizard. My Device is setup and ready to be found 16.
17. Select the Bluetooth Device that you want to add. Please click “ Next” 18. Passkey Please choose “Don’t use a passkey” 19. Connecting 20.
21. Bluetooth Device If your OS system is Windows 2000/XP, you can install WIDCOMM Bluetooth software. WIDCOMM Bluetooth software setup STEP 1 Software Installation 1. Click “Windows 2000/XP – WIDCOMM Bluetooth software” 2. Welcome The software will automatically begin. The window welcomes you to install shield Wizard for Bluetooth software.
3. License Agreement Read the license agreement, if you accept, select the check button. To continue, click “Next” 4. Locating of installation If you wish to select another location where the software will be installed, click “Change” and select or enter a new location. The default location is recommended. To continue, click “Next” 5. Install You are now ready to install.
6. Copying The installation process will now begin. Please wait while files are being copied to your computer. The progress bar will indicate the portion that has been completed. 7. Driver Signature (Windows XP only) You will be prompted with a driver Signature Notice. To continue, click “OK” 8. Device Not Found At the Bluetooth device not found prompt, directly plug the USB Bluetooth Adapter into an available USB port. Please continue with SETP 2 – Hardware Installation.
STEP 2 Bluetooth Adapter Hardware Installations 9. If you have successfully inserted the WIDCOMM Bluetooth software pleases continue.The green LED (light) on the device will be lit, if Bluetooth Adapter is successfully inserted. To continue, click “OK ” 10. Finish Now you have completed the installation of the WIDCOMM Bluetooth software. To finish the installation, click “Finish”. 11. Restart Windows If you have not been prompted, please restart windows.
STEP 3 Initial Set up (only for the very first time installation) 12. Open My Bluetooth Place Double-click the My Bluetooth Places on your desktop. 13. Run Initial Bluetooth Configuration The Initial Bluetooth Configuration Wizard will appear. The default options are recommended. You may uncheck them respectively if you do not wish the My Bluetooth Places icon to be placed. To continue, click “Next” 14. Give your computer a Device Name.
the icon in which you identify yourself to another Bluetooth user. To continue, click “Next” Each Bluetooth device that wishes to connect to your computer must have a unique Computer name (different to all other users connecting). 15. Bluetooth Service The Initial Bluetooth configuration Wizard window will now allow you to enable or disable Bluetooth Services. (Refer to the Bluetooth Services section for information on services.) 16.
wish to offer. Disable or enable by clicking one the check box next to the name of the service you wish to alter. □ :Service enabled □: Service disabled. By default all services are enabled (all check boxes ticked). The default setting is recommended. You can choose to disable or enable services at any time. To continue, click “Next” 17. Search and configure other Bluetooth Devices. Please click “SKIP”. Search and configure Bluetooth Device later.
STEP 4 Start to Pair Bluetooth Pen Pad 19. Open My Bluetooth Places Tip: Bluetooth System Tray The Bluetooth icon in the Windows Systems Tray indicates the USB Bluetooth Adapter Status. Enabled Disabled Connected Blue with White Blue with Red Blue with Green To open My Bluetooth Places, go to your windows desktop and double-click the icon. 20. Searching Bluetooth Pen Pad Click “View devices in Range” for searching and connect to nearby Bluetooth enabled devices.
Please double-click the Bluetooth Pen Pad. And click “OK”. Make sure Bluetooth Pen Pad is power on and the Bluetooth Adapter is plugging into PC and the icon in Windows Systems Trays is Blue with White. The very first time you want to connect Bluetooth Pen Pad to a new PC (or new Adapter). You may need to use your mouse to click the “confirmed icon” and waiting for the PC to recognize Bluetooth Pen Pad.
Once the icon is works now. , the Bluetooth Pen Pad If you would like to know more about how to use Bluetooth Adapter, please reference from the user manual of USB Bluetooth Adapter. How to Unpairing Once you want to cut down the connection between Bluetooth Pen Pad with your PC. Please follow the next step to unpair. • Windows 2000/ XP with WIDCOMM Bluetooth software 1. Double click the My Bluetooth Places on your desktop. 2. Click View Devices in Range.
The Bluetooth Connection Status Windows will appear. 4. Click Disconnect. Now you can safely disconnect your Bluetooth Pen Pad. • Above Windows XP Service Pack 2 with Microsoft Bluetooth software Select Bluetooth Pen Pad, then click Remove to disconnect your Bluetooth Pen Pad. To make sure to cut down the connection, once you have done the above step from PC side, please also keep pressing the unpairing button on the Bluetooth Pen Pad for at least 5 seconds.
Troubleshooting 1. When I search for my Bluetooth Pen Pad, many devices appear that I do not recognize. Because Bluetooth 1.2 class 2 has a range of up to 10 meters, you will detect devices beyond the Bluetooth Pen Pad that you are searching for. 2. My Bluetooth Pen Pad connection drops out when I use my cordless phone. Bluetooth uses the 2.4Ghz unlicensed ISM band, which is the same as some high end cordless phone, video transmitters, and some other wireless devices.
pairing section. b.You will need to restart your PC. 6. There is a longer than usually delay with my Bluetooth Pen Pad. You will need to move closer to your computer and try replacing the batteries. Or you may check whether your PC is stable. Or maybe there are other 2.4G devices interfere now. Try to re-pair again. 7. I have lost my nib ( the tip of my pen) Your pen is supplied with two spare nibs, which you can use to replace the tip. 8. The pressure sensitivity does not seem to work in my application.
Product Specification Bluetooth Pen Pad Item Description Technology Electromagnetic Bluetooth Version 1.2 Class 2 Connection Distance 10 meters Dimension 239*251*30mm Active Area 6”*4.5”(152mm*114mm) Weight 493g (545g with batteries) Writing height 10mm Macro key 12 (Press 1.
Connection Interface Bluetooth Version 1.2 Class 2 USB 1.1 Full speed Resolution 1000 Lpi Pen Pressure 512 Levels Reporter Rate Bluetooth mode :162 report/per second USB mode :183 report/per second Bluetooth dongle capacity Windows 2000/ XP SP1 : only support WIDCOMM driver (5.0.1.
Maintenance 1. Do not drop, puncture or disassemble the tablet. 2. Remove batteries during long periods between uses. 3. Avoid all contact with water and dry hands before using. 4. Do not expose the tablet to high temperature or leave it in direct sunlight. 5. Avoid pressing hard on the tablet body.
Environment Environment always influences the receiving quality of your tablet. The best environment for your tablet is where no other cordless products are functioning, such as microwave ovens. Cement walls and wooden walls absorb radio wave and decrease receiving quality. Open space without barriers is the best environment for your tablet.
82-910W02110-000v1.
