Quick Start Guide

WBX
Model # WBX-XX-XX
Introduction
This document provides basic info for wireless
set up.
Scan now to download the full
Quick Start Guide for advanced
configuration; or go to:
General Information
Your product may be custom configured with the
service code “KBC-PRE-CONF”. In that case,
refer to all provided documentation for IP
addresses and any other pre-set configuration.
KBC remote power solutions may replace a
supplied power supply / injector in your
application.
Inspect all contents upon receipt. Claims and
discrepancies must be reported within 1 week of
original product shipment from KBC.
Contact Us Now:
On your mobile device, go to our website at:
http://www.kbcnetworks.com
 Tap on WBX-XX-XX Wireless
(Wireless Products)
 Scroll down and tap “Contact Us Now” in
the blue bar.
Our full Quick Start Guide online will
answer in depth questions.
Feel free to call us M-F 8-5 PT 949-297-4930
Warranty Information
Laptop/Desktop:
 www.kbcnetworks.com
 Hover over “About Us”
 Click on “Policies & Procedures”
 Scroll down to “Warranty”
Mobile:
 www.kbcnetworks.com
 Click/tap WBX-XX-XX Wireless
 Click/tap Search bar and search for
“Warranty”
 Click on “Policies & Procedures” from
search results.
 Scroll down to “Warranty”
Out of the Box Pre-set Configurations
The WBX-XX-XX is pre-set as an APHost, if you
need for it to be a Client you will need to access
the interface and change the mode.
Parameter Setting
LAN IP Address 192.168.1.152
GUI User ID admin
GUI Password password
Mode Access Point WDS
SSID WBX-XX-XX
Pre-shared Key 11111111
Channel/Frequency 149 (5.745 GHz)
Chan Spectrum Width 20/40/80 MHz
TX Power Output Max
Antenna Gain
4.0 dBi
Approved Power Methods:
1. Supplied injector in the unit boxes:
 Connect to POE Port via Cat5e / Cat6
2. POE port on 802.3af PoE PSE device:
3. Injector in a remote power solution:

Connect to injector in SPB series.
(If applicable – common)

Connect to injector in AL2 / AL5 series
solar kit. (if applicable - uncommon)

Connect to injector in UAL2/UAL5
series UPS kit. (if applicable - uncommon)
MAC-Filter Disabled
FCC Statement
Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Note : This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates,uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: —Reorient or
relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment .This equipment should be installed
and operated with minimum distance 30cm between the radiator&
your body.