Manual WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN PERSPECTO® CP, Control Panel with CoDeSys Target Visualization Version 1.0.
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN © 2018 WAGO Kontakttechnik GmbH & Co. KG All rights reserved. WAGO Kontakttechnik GmbH & Co. KG Hansastraße 27 D-32423 Minden Phone: Fax: +49 (0) 571/8 87 – 0 +49 (0) 571/8 87 – 1 69 E-Mail: info@wago.com Web: http://www.wago.com Technical Support Phone: Fax: +49 (0) 571/8 87 – 4 45 55 +49 (0) 571/8 87 – 84 45 55 E-Mail: support@wago.
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN Table of Contents 3 Table of Contents 1 1.1 1.2 1.3 1.4 1.5 2 2.1 2.1.1 2.1.2 2.1.3 2.1.4 2.2 3 3.1 3.2 3.2.1 3.2.2 3.3 3.3.1 3.3.2 3.3.3 3.3.4 3.3.5 3.3.6 3.4 3.5 3.6 3.6.1 3.7 3.7.1 3.7.2 3.7.3 3.7.4 3.7.5 3.7.6 3.8 3.9 4 4.1 5 5.1 5.2 5.3 Notes about this Documentation .............................................................5 Scope of Validity .....................................................................................5 Copyright ..
Table of Contents 6 Commissioning .......................................................................................30 6.1 6.2 6.2.1 6.2.2 6.2.3 6.3 6.3.1 6.3.2 6.3.3 6.3.4 6.3.5 6.3.6 6.3.7 6.3.8 6.3.9 6.3.10 6.4 7 7.1 WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN Switch on ..............................................................................................30 IP Address of the Device ...................................................................... 31 General ...........
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN 1 Notes about this Documentation 5 Notes about this Documentation The CP 150 XGA TV CAN 762-3150/000-003 shall only be installed and operated according to the instructions in these operating. Always retain this documentation! This documentation is part of the product. Therefore, retain the documentation during the entire service life of the product. Pass on the documentation to any subsequent user.
1.3 Notes about this Documentation WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN Symbols Personal Injury! Indicates a high-risk, imminently hazardous situation which, if not avoided, will result in death or serious injury. Personal Injury Caused by Electric Current! Indicates a high-risk, imminently hazardous situation which, if not avoided, will result in death or serious injury.
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN Notes about this Documentation 7 Additional Information: Refers to additional information which is not an integral part of this documentation (e.g., the Internet). Manual Version 1.0.
1.4 Notes about this Documentation WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN Number Notation Table 1: Number Notation Number Code Decimal Hexadecimal Binary 1.5 Example 100 0x64 '100' '0110.0100' Note Normal notation C notation In quotation marks, nibble separated with dots (.) Font Conventions Table 2: Font Conventions Font Type italic Menu > Input “Value” [Button] [Key] Manual Version 1.0.2 Indicates Names of paths and data files are marked in italic-type. e.g.: C:\Program Fil
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN 2 Important Notes 9 Important Notes This section includes an overall summary of the most important safety requirements and notes that are mentioned in each individual section. To protect your health and prevent damage to devices as well, it is imperative to read and carefully follow the safety guidelines. 2.1 Legal Bases 2.1.1 Subject to Changes WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any alterations or modifications.
Important Notes WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN following actions will result in the exclusion of liability on the part of WAGO Kontakttechnik GmbH & Co. KG: • • • Repairs, Changes to the hardware or software that are not described in the operating instructions, Improper use of the components. Further details are given in the contractual agreements. Please send your request for modified and new hardware or software configurations directly to WAGO Kontakttechnik GmbH & Co. KG.
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN 2.2 Important Notes 11 Safety Advice (Precautions) For installing and operating purposes of the relevant device to your system the following safety precautions shall be observed: Do not work on devices while energized! All power sources to the device shall be switched off prior to performing any installation, repair or maintenance work. Install only in appropriate housings, cabinets or in electrical operation rooms! The device is an open unit.
Important Notes WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN Do not use any contact spray! Do not use any contact spray. The spray may impair contact area functionality in connection with contamination. Do not use in telecommunication circuits! Only use devices equipped with ETHERNET or RJ-45 connectors in LANs. Never connect these devices with telecommunication networks.
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN 3 Device Description 13 Device Description The 762 Series panels are used to operate and visualize the controllers of the WAGO-I/O-SYSTEM. The integrated WAGO-AUTOMATION COCKPIT development environment is used to program the panels and controllers. 3.
Device Description 3.2 View 3.2.1 Front View Figure 1: Front View Table 3: Legend for Figure “Front View” No. 1 2 Manual Version 1.0.
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN 3.2.2 Device Description 15 Back View Figure 2: Back View Table 4: Legend for Figure “Back View” No.
Device Description 3.3 Connectors 3.3.1 X1 – Supply Voltage WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN Use the X1 connection for the device power supply. More information about the power supply and power consumption is available in the "Technical Data" section. Figure 3: Connector X1 – Supply Voltage Table 5: X1 Pin Assignment Pin 1 2 3 Manual Version 1.0.
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN 3.3.2 Device Description 17 X2 – Serial Interface RS-232/RS-485/RS-422 (COM 2) The interface is designed as a combined RS-232/RS-485/RS-422 interface. It is DC coupled with the power supply of the device. It is generally used for communication (service devices, modem operation, etc.). The connected data cable must be shielded.
Device Description 3.3.3 WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN X3 – Serial Interface RS-232 (COM 1) The interface is designed as an RS-232 interface. It is DC coupled with the device ground. The interface is used for modem operation or for user-specific protocols. The connected data cable must be shielded. A null modem connection is used to connect to another device with RS-232 interface. A 1:1 connecting cable is used to connect to a modem.
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN 3.3.4 Device Description 19 X5 – CAN 0 Interface This interface is designed as an RJ45 connector. The interface is used to communicate with CANopen-enabled modules. The CAN 0 interface is designed with electrical isolation in accordance with ISO 11898. A terminating resistor that can be switched on by relay is integrated in the device in accordance with ISO11898. The connected data cable must be shielded.
Device Description 3.3.5 WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN X6 – ETHERNET Interface 10/100/1000 MBit An RJ45 jack is used for the ETHERNET interface. The connections and cables must meet CAT.5 and the guidelines for ETHERNET interfaces 10/100/1000 MBit. If there are more than 2 devices in a network, then they must be connected to each other by a HUB or SWITCH. The type of connection is detected automatically via auto-MDI(x).
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN 3.3.6 Device Description 21 X8/X9/X10/X11 – USB Interfaces The interfaces are designed as USB host interfaces, type A. The following table and illustration provide information on the pin assignment of the interfaces. The interface connection meets the USB specification 2.0.
3.4 Device Description WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN Battery Case Do not charge, disassemble or burn the battery! Incorrect use of the lithium battery contained in this device may cause damage incurred by fire or chemical burns. The battery must not be charged, disassembled, burned or exposed to temperatures exceeding 100°C (212°F).
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN 3.5 Device Description 23 Slot for Memory Card The panel 762-3150/000-003 is equipped with a Flash memory slot on the side for a CF card. It supports cards with a 2 GB maximum. Supported memory cards (item no. 758-879/000-000) are available from WAGO. Manual Version 1.0.
Device Description 3.6 Operating Elements 3.6.1 Service Button WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN The service switch on the back of the device is used to call up the Windows CD desktop. The WAGO Control Center can be launched, for example, to configure the device. Figure 10: Service Button Manual Version 1.0.
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN 3.7 Technical Data 3.7.1 Housing Device Description 25 Table 11: Technical Data ‒ Housing Front panel Housing material Dimensions (W x H x L) Panel cutout (B x H) Fixing means Surrounding air temperature, operation Surrounding air temperature, storage Relative humidity (without condensation) Weight Degree of protection 3.7.2 Anodized aluminum, natural, polyester film Painted sheet steel 398 x 306 x 77 mm 383 x 291 mm 6 clamping elements 0 °C .
Device Description 3.7.4 WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN Hardware Table 14: Technical Data ‒ Hardware Processor RAM / Flash / SRAM Memory expansion 3.7.5 Intel Atom® N270 1.6 GHz 256 MB / 128 MB / CF card (max. 2 GB) Software Table 15: Technical Data ‒ Software Operating system Software configuration 3.7.6 Windows CE 6.
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN 3.8 Device Description 27 Approvals The following approvals have been granted to 762-3150/000-003 panels: Conformity Marking 3.9 Standards and Guidelines 762-3150/000-003 panels meet the following requirements on emission and immunity of interference: EMC CE-Immunity to interference EN 61000-6-2 EMC CE-Emission of interference EN 61000-6-4 Manual Version 1.0.
Mounting 4 Mounting 4.1 Front Panel Installation WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN The devices are intended for installation in switch cabinets, for example. Vertical installation of the panels is recommended. Note about differing mounting position! The operating temperature ranges specified in the technical data apply to the recommended mounting position. If the panel is mounted in a position different than recommended, cooling can be affected.
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN 5 Connect Devices 5.1 Supply voltage Connect Devices 29 Connect the supply voltage to contact 1 (24 VDC) and contact 2 (GND) of the included 734-103 female connector. Use an appropriate operating tool to open the CAGE CLAMP® connections. Feed the 7 mm stripped conductors with a cross section of max. 1.5 mm² into the connections and remove the operating tool. 5.
Commissioning 6 Commissioning 6.1 Switch on WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN After applying the power supply, the device switches on automatically. After the boot and self-test phase that lasts about 10 seconds, the programs set in the WAGO Control Center (e.g. HMI runtime) are launched automatically.
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN 6.2 IP Address of the Device 6.2.1 General Commissioning 31 The device can be programmed using WAGO-I/O-PRO / CODESYS. Therefore, a TCP/IP connection is required. An IP address must be assigned to the device after switching it on for the first time. The WAGO Control Center installed on the device is used to assign the IP address by default (observe "Setting the IP Address" section).
Commissioning WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN Figure 12: IP Address 6.2.3 IP Address When using a crossover cable to connect between the panel and configuring PC directly, it is recommended that both devices have fixed IP addresses with an open address in the range 192.168.1.xxx. In this case, the subnet mask is automatically set to 255.255.255.0. There is no default gateway. IP Address The devices must be set to different IP addresses. Manual Version 1.0.
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN 6.3 Commissioning 33 The WAGO Control Center The WAGO Control Center can be used to configure the device. Settings for the Autostart programs, uses, FTP/HTTP and RAS access can be made. General device settings can also be checked and modified. 6.3.
Commissioning 6.3.2 WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN “General” Tab Figure 13: “General” Tab Device Information Information about the device is found here. This information is important, for example, for support cases. General Watchdog: A watchdog can be configured here, which can restart the device if it crashes after a set time. Don’t start Windows CE Shell: If the checkbox is enabled, the Windows CE desktop can no longer be launched. The task bar is no longer displayed.
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN 6.3.3 Commissioning 35 “Autostart Applications” Tab You can enter programs here that should launch automatically after booting. The target-visu runtime, the autoscan function and the WAGO Control Center are entered here by default. The time window for launching the programs after the boot and self-test phase of the device can also be set here. Figure 14: “Autostart Applications” Tab Manual Version 1.0.
Commissioning 6.3.4 WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN “Users” Tab You can create FTP users, grant rights and assign directories. The menu is generally self-explanatory. Figure 15: “Users” Tab User/Virtual Roots: A directory from another (protected) tree, for example, can be put in the user's home directory. By doing so, you gain access to this and subsequent directories. FTP Home Directory/HTTP directory path: The user starts downwards from this menu.
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN 6.3.5 Commissioning 37 “FTP” Tab You can configure the FTP server of the device here. More information about creating users is available in the "Users Tab" section. Figure 16: “FTP” Tab Manual Version 1.0.
Commissioning 6.3.6 WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN “HTTP” Tab You can configure the Web server of the device here. Figure 17: “HTTP” Tab Application example: An \httptest directory with the /test alias was created on the flash disk. A Web page index.htm was created in this directory. The page can be used in a Web browser to access the following address: http://[IP address of the device]/test Manual Version 1.0.
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN 6.3.7 Commissioning 39 “RAS” Tab The Remote Access Service (RAS) is a service for remote access to a Windows CE device. Figure 18: “RAS” Tab Both RAS functions, server and client, are supported. The connection between a RAS client and the RAS server can be established via a modem, VPM or direct connection. For more information about the Remote Access Service (RAS) of the device, please contact WAGO Support. Manual Version 1.0.
Commissioning 6.3.8 WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN “Backup/Restore” Tab You can save and restore the device configuration and project data, for example, on a memory card. Doing so allows you to restore the data to the new device when replacing a defective device without having to redo all the settings. What data and files should be saved is defined by the backup_restore.cfg file. The file is stored on the device via the path \Flashdisk\SysExtras\Tools\ backup_restore.
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN Commissioning 41 Figure 19: “Backup/Restore” Tab The Backup button is used to save the parameters defined in the backup_restore.cfg and entries on the target data carrier. The Restore button is used to restore the parameters defined in the backup_restore.cfg and entries on the device. Create backup! It is recommended that you create a backup after commissioning the device and to keep the backup in a safe place.
Commissioning 6.3.9 WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN “Advanced” Tab You can perform advanced settings for the device. The menu is generally selfexplanatory. Figure 20: “Advanced” Tab Restrictions for Control Panels with CoDeSys Target Visualization Control Panels with Target Visualization have no contrast and touch beeper setting. Communication CAN bus termination: Select this checkbox to switch on the CAN bus termination resistor of the CAN-0 interface.
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN 6.3.10 Commissioning 43 Saving the Configuration After configuring the panel, the settings must be permanently saved in the registry. Call up the following utility program: Start -> Programs -> Utilities -> Save Registry Fail-safe saving of the configuration! If the settings are not saved as described, they are lost when the device is restarted. Manual Version 1.0.
6.4 Commissioning WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN Target-Visu The following status window appears after starting the Target-Visu panel: Figure 21: PLCWinCE Status Window This window displays the loaded CODESYS programs with project details. The CODESYS program can also be started or reset from here. The [Shutdown] button can be used to exit the runtime. Manual Version 1.0.
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN 7 Service 7.1 Battery Maintenance Service 45 Do not charge, disassemble or burn the battery! Incorrect use of the lithium battery contained in this device may cause damage incurred by fire or chemical burns. The battery must not be charged, disassembled, burned or exposed to temperatures exceeding 100°C (212°F). Replace the battery only with an identical one! Only replace the lithium battery with an identical one.
List of Figures WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN List of Figures Figure 1: Front View ...........................................................................................14 Figure 2: Back View ...........................................................................................15 Figure 3: Connector X1 – Supply Voltage...........................................................16 Figure 4: Connector X2 – Serial Interface RS-232/RS-485/RS-422 ....................
WAGO PERSPECTO® 762 762-3150/000-003 CP 150 XGA TV CAN List of Tables 47 List of Tables Table 1: Number Notation ................................................................................... 8 Table 2: Font Conventions .................................................................................. 8 Table 3: Legend for Figure “Front View” .............................................................14 Table 4: Legend for Figure “Back View” ........................................................
WAGO Kontakttechnik GmbH & Co. KG Postfach 2880 • D - 32385 Minden Hansastraße 27 • D - 32423 Minden Phone: +49 571 887 – 0 Fax: +49 571 887 – 844169 E-Mail: info@wago.com Internet: http://www.wago.