Datasheet

750-563
1
255
1.6
2-Channel Analog Output Module, 0/4 ... 20 mA / 6 ... 18 V DC
16 bits, configurable
Delivered without miniature WSB markers
A1+
A2–
13 14
D
C
B
A
750-563
M
M
S1+
S2+
S1–
S2–
+ AO 2
Data contacts
+ Sense AO 2
Common
(ground)
Function AO 1
Error AO 1
+ AO 1
Common
(ground)
– Sense AO 2
+ Sense AO 1
– Sense AO 1
Power jumper contacts
Function AO 2
Error AO 2
750-563
1
2
3
4
5
6
7
8
+ AO 1
Common
(ground)
Common
(ground)
+ 24 V
0 V
+ Sense AO 1
- Sense AO 1
+ Sense AO 2
- Sense AO 2
+ AO 2
AO
+24 V
0 V
100 nF
10 nF
Function Error
Common
(ground)
Logic
10 nF
A
D
I
U
0...20mA
6...18V
The analog output module generates output currents ranging from
0/4 to 20mA or output voltages in the range from 6 to 18V for the field.
Output ranges can be configured via WAGO-I/O-CHECK or GSD files.
The module has two short circuit-proof output channels and enables direct
connection of two 2-line actuators on the connections AO 1 and ground or
AO2 and ground. Signals are output via AO 1 or AO 2. In addition, the sense
lines from 4-line actuators can be connected to the connections Sense AO1 and
+Sense AO1 or Sense AO2 and +SenseAO2.
Both output channels have a common ground potential.
The output signal is electrically isolated and transmitted with a resolution of
16 bits.
Both the internal system and the field side supply power the module.
Description
Item No.
Pack.
Unit
2 AO 0/4-20mA / 6-18V DC 16 Bit 750-563 1
Accessories
Item No.
Pack.
Unit
Miniature WSB Quick marking system
plain 248-501 5
with marking see pages 352 ... 353
Approvals
Also see "Approvals Overview" in Section 1
Conformity marking 1
r UL 508
r ANSI/ISA 12.12.01 pending
4 EN 60079-0, -15
EN 61241-0, -1
pending
Technical Data
No. of outputs 2
Current consumption (internal) 80 - 110mA
Voltage via power jumper contacts 24 V DC (-15 % ... +20 %)
Output voltage 6 V ... 18 V (switchable)
Output current 0/4 mA ... 20 mA (switchable)
Load impedance > 1.8 kΩ (voltage output)
< 500 Ω (current output)
Resolution 16 bits
Conversion time (typ.) 5 ms
Recovery time (typ.) < 300 μs
Measuring error (25°C) < ± 0.05 % of the scale end value
Temperature coefficient < ± 100ppm
Isolation 500V system/supply
Bit width 2 x 16 bits data
2 x 8 bits control/status (option)
Wire connection CAGE CLAMP
®
Cross sections 0.08 mm² ... 2.5 mm² / AWG 28 ... 14
Stripped lengths 8 ... 9 mm / 0.33 in
Width 12 mm
Weight 53.5 g
EMC: 1 - immunity to interference acc. to EN 61131-2 (2003)
EMC: 1 - emission of interference acc. to EN 61131-2 (2003)
WAGO Kontakttechnik GmbH & Co. KG
Subject to design changes 18.05.2012
Postfach 2880 - D-32385 Minden
Hansastr. 27 - D-32423 Minden
Phone: [phone] E-Mail: [e-mail]
Fax: [phone] www.wago.com