Datasheet

2857-401
3
134
INTERFACE ELECTRONIC
JUMPFLEX
®
Transducers
Universal Isolation Amplifier
12,5 mm/0.49 in
107 mm/4.21 in
110 mm/4.33 in
Configuration via:
Interface
configuration
software
Interface
configuration
app
Configuration
display
DIP switch
Short description:
The Universal Isolation Amplifier converts, amplifies, filters and electrically isolates analog
signals.
Features:
• Analog unipolar/bipolar signals at input/output
• A digital signal output reacts to configured measuring range limits (switching ON/OFF
delay and threshold value switch function configurable with up to two threshold valu-
es).
• A digital HOLD input freezes the output signal.
• Clipping capability provides analog signal limitation to output end values.
• Adjustable software/hardware filter
• Input/Output response simulation via configuration display
• Safe 3-way isolation with 4 kV test voltage acc. to EN 61140
Description
Item No.
Pack.
Unit
JUMPFLEX
®
Transducer, for DIN 35 rail 2857-401 1
Universal Isolation Amplifier
Technical Data
Configuration:
Configuration DIP switch, interface configuration
software, interface configuration app,
configuration display
Input:
Input signal Current:
± 1 mA; 0 … 1 mA;
± 10 mA; 0 … 10 mA; 2 … 10 mA;
± 20 mA; 0 … 20 mA; 4 … 20 mA;
± 100 mA; 0 … 100 mA
Voltage:
± 1 V; 0 … 1 V;
± 10 V; 0 … 10 V; 2 … 10 V;
± 30 V; 0 … 30 V;
± 100 V; 0 … 100 V;
± 200 V; 0 … 220 V
Input resistance ≥ 1 MΩ (U input); ≤ 50 Ω (I input)
Max. operating frequency 10 kHz / 5 kHz / 100 Hz / 30 Hz
(configurable via DIP switch)
Input – Digital:
HOLD signal 11.8 V … U
S
Output:
Output signal Current:
± 10 mA; 0 … 10 mA; 2 … 10 mA;
± 20 mA; 0 … 20 mA; 4 … 20 mA
Voltage:
± 5 V; 0 … 5 V; 1 … 5 V;
± 10 V; 0 … 10 V; 2 … 10 V
Load impedance Current: ≤ 600 Ω;
Voltage: ≥ 1 kΩ
Overload capacity -250 V; +250 V / -120 mA; +120 mA
Output – Digital:
Max. switching voltage Supply voltage applied -0.3 V
Max. continuous current I
DO
100 mA (no internal restriction)
Technical Data
General specifications:
Supply voltage U
S
24 VDC
Supply voltage range 16.8 V … 31.2 V (-30 % … +30 %)
Current consumption at 24 VDC ≤ 70 mA (+ IDO)
Response time (T
10-90
)< 1 ms
Transmission error ≤ 0.1 % of the full scale value
Temperature coefficient ≤ 0.01 %/K
Environmental requirements:
Ambient operating temperature -40 °C … +70 °C
Storage temperature -40 °C … +85 °C
Safety and protection:
Test voltage
(input/output/supply) 4 kV AC, 50 Hz, 1 min.
Connection and type of mounting:
Wire connection CAGE CLAMP
®
S (picoMAX
®
5.0)
Cross sections solid/fine-stranded:
0.2 … 2.5 mm² / AWG 24 … 12
Strip length 9 … 10 mm / 0.35 … 0.39 in
Dimensions and weight:
Dimensions (mm) W x H x L 12.5 x 107 x 110
Height from upper-edge of DIN 35 rail
Weight 86 g
Standards and approvals:
Conformity marking 1
Standards/Specifications DIN EN 61010-1:2010;
DIN EN 60664-1:2008;
Safe isolation acc. to
DIN EN 61140:2002; IEC 61000-6-2;
IEC 61000-6-4
Accessories: For accessories, see Full Line Catalog
INTERFACE ELECTRONIC 2012/2013
WAGO Kontakttechnik GmbH & Co. KG
Subject to design changes 30.10.2013
Postfach 2880 - D-32385 Minden
Hansastr. 27 - D-32423 Minden
Tel.: [phone] E-Mail: [e-mail]
Fax: [phone] www.wago.com