WMTS T1 Access Concentrator V3000 System Configuration Guide Network Release 3.6 Manual Version: 1.1.
Copyright and Trademark Information: © 2005 Vyyo Inc. All rights reserved. Vyyo Inc. reserves the right to alter the equipment specifications and descriptions in this publication without prior notice. No part of this publication shall be deemed part of any contract or warranty unless specifically incorporated by reference into such contract or warranty. The information contained herein is merely descriptive in nature, and does not constitute a binding offer for the sale of the product described herein.
Table Of Contents Table Of Contents................................................................................ 3 Installation and Safety Information ...................................................... 7 Chapter 1. System Configuration Introduction.................................. 10 1.1 Overview...............................................................................................10 1.2 Equipment Capabilities .........................................................................13 1.
3.1.4 Ranging ..........................................................................................29 3.1.5 Establish IP Connectivity ...................................................................29 3.1.6 Establish Time of Day .......................................................................30 3.1.7 Transfer Operational Parameters .......................................................30 3.1.8 Registration .............................................................................
Chapter 7. Setting the WMTS IP Address ........................................ 93 Chapter 8. Installing Vyyo Servers for WMTS Operation ............... 106 8.1 Installing The Time Server:.................................................................106 8.2 Installing the Pumpkin TFTP Server: ..................................................106 8.3 Installing IPLease DHCP Server:........................................................109 8.3.1 dhcpsvr.ini .........................................
D.1 The Vyyo Configuration Tool Menu (exploded view) ..............................129 D.2 Launching the Vyyo Configuration Tool from the “Start” Menu ...............130 D.3 Launching the Vyyo Configuration Tool from the NMS ...........................133 Appendix E: Vyyo Configuration Tool – Additional Functions ......... 136 E.1 Adding and Deleting a Modem ...........................................................136 INDEX www.vyyo.com 137 Table Of Contents – p.
Installation and Safety Information The following information is provided to ensure safe operation of this equipment. Vyyo assumes no liability in the event that the customer fails to comply with the following safety precautions and warnings. System Power-on AC System Power AC System The WMTS power supplies are factory wired for 115 ~ 220 VAC (2 X 200W). A power cords are provided to connect the unit to the power source. To operate the WMTS, turn ON the power switch at the rear panel.
Earthing The minimum cross sectional area of the protective earthing should be 1mm2 . General T1 Cable T1 cable to be used with WMTS T1 ports is only 26AWG communication cable (the common cable for this application). General Repairs Safety General 1. Repairs of WMTS should take place only in Vyyo company service laboratories or in other Vyyo formally approved distributors service laboratories. 2. In case of field handling - Disconnect the unit from power supply for safest repair. 3. www.vyyo.com 2.
Safety Summary Warnings: Carefully connect units to the supply circuit so that wiring is not overloaded. For DC system connect Ground first (or remove Ground last for disconnect). Read the installation instructions before connecting the system to its power source. Secure all power cabling when installing this unit. Do not touch the power supply when power cord is connected.
Chapter 1. System Configuration Introduction This guide is intended as a practical aid for the Technicians, Operators and Field Service Engineers responsible for quickly configuring Vyyo systems at most common installations. It is not intended as a substitute for a detailed reference manual. NOTE: Throughout this manual the terms modem and WMU are used interchangeably. The term “WMU” refers to “Wired/wireless Modem Unit”. In some instances the actual modem model (V280, V311, etc.
(Cable/Wireless Modem Termination System) end and an E1/T1 capable cable/wireless modem at the downstream end. The data from the IP, E1/T1, or PSTN layer are encapsulated as DOCSIS frames which in turn are converted into RF signals and sent over the air or via an HFC (Hybrid Coax Fibre) plant between the WMTS and modem. Important Note: connectivity MUST be obtained at each layer, beginning with the lowest (RF link) in order to establish full communication. www.vyyo.
The following diagram illustrates this in the form of a three layer protocol stack: WMTS Modem IP, E1/T1, POTS Layer 3 IP, E1/T1, POTS DOCSIS Layer 2 DOCSIS RF Link Layer 1 RF Link This illustration shows how a complete system is connected: Provisioning Services Tx PC Internet 100BaseT 100BaseT RF Cloud or Cable Plant Rx MTA WMTS V280 Modem RF Coax IP Network Packet Voice Server H.
There are different configuration requirements for each layer and different software tools accomplish this task. The configuration of the RF link is typically unique to each installation with the particular downstream and upstream frequencies, modulations and bandwidths being the critical parameters that must be set on the modem and WMTS. Whereas there is no set standard for implementing an RF link, DOCSIS is a fully specified protocol as are the upper layers (IP, E1/T1 or PSTN).
All Universal cards are the physically identical: the card attached to each of them in the rear slots and the application downloaded during initial startup determine the function of the card (Upstream, Downstream or Control & Forward). In the rear slots, one Downstream and one Upstream RF interface card are required. Each of these corresponds to its companion Universal card. The “Quad” downstream card has four RF connectors and provides four downstream channels.
in the rack, to 8U. The eight bay chassis contains eight slots in the front, six slots in the rear, and a mid-plane card in between, used to interface the cards. Blank panels cover unused slots. A standard 33 MHz, 32 bit Compaq PCI bus is used to transfer traffic and data between the system cards. The power supplies, Master4 card and the universal cards are inserted in the front slots of the chassis. The Quad Downstream, Hex Upstream, and E1/T1 cards are inserted in the rear slots of the chassis.
1.4 Modems 1.4.1 Modems with DOCSIS and IP only The V280 is Vyyo’s “IP-only” modem. It uses an RJ45 connector (shown below) on the rear panel to provide IP connection to the customer’s equipment. The V280 supports up to 63 data users simultaneously and provides privacy, authentication, service classification, prioritization, and traffic shaping. The USB connector is not supported at this time. Check with Customer Support for updates as they become available if you need this capability. Figure 1-3.
1.4.2 Modems with DOCSIS, IP and E1/T1 The V311 is a V280 modem (to provide the DOCSIS layer) with one E1/T1 interface (via an RJ45 connector on the front panel) added. In addition to IP connectivity, it supports circuit switched E1/T1 applications. It has one 100 BASE-T port for IP data and one E1/T1 port which can support up to 32/24 time slots. The E1/T1 application supports framed or unframed E1/T1 services.
The V312 is identical to the V311 but has two E1/T1 interfaces instead of one. The WMTS at the head end requires one or two E1/T1 interface cards (plugged into the rear slots, with the second E1/T1 card attached to the first one as a daughter board) to work with the V311 or V312. The E1/T1 connection will be terminated at one of the ports on this (rear) E1/T1 interface card(s). In addition, a separate software load is required. All modems have four LED indicators, described below. Figure 1-6.
1.4.4 Modems with DOCSIS and IP Only With Built in UHF Radio The V284 modem is a basic V280 modem integrated with a built-in UHF radio that provides an upstream RF output in the 710-716 MHz range. Internally the V284 has a factory set intermediate frequency of 44MHz which is converted up to yield an appropriate upstream frequency (This is preset at the factory for 700MHz in the United States). The downstream frequency ranges from 740-746MHz.
1.
Chapter 2. Configuration Overview This section of the System Configuration Guide features a short overview of each component/layer of the System including the WMTS and the modems. The last section is a summary presented as a matrix that shows the relationships between the various tools and files. The components and layers are described below. • Network Servers o DHCP Server o TFTP Server o Time of Day (ToD) Server • RF Link Layer • DOCSIS Layer 2.
Your System Engineer must develop a detailed system plan that accounts for each of these variables. This plan must include the assignments of downstream frequencies, modulations (and other RF parameters) and upstream channel IDs assigned to the various modems deployed in the network.
First, the modem searches for a signal at its preprogrammed Downstream Frequency. Once having locked to that downstream channel, the modem receives upstream channel descriptors (UCDs) from the WMTS that describe the available upstream channels. NOTE: The WMTS must be configured to construct the UCDs so that they correspond to the site preplan. Use the Vyyo Configuration Tool to accomplish this if any changes are required.
For the ipLease DHCP Server tool, the CM.SRC file is an ASCII text file that may be edited using any text editor (such as Notepad). This document describes the configuration process using the ipLease tool. The changes are similar for other DHCP servers. Note that if another operating system, such as the Windows 200x Server, is used a DHCP server is often included. Check with your Vyyo representative to make sure the DHCP server is compatible.
standard IP-only modem. The same modem configuration file may be used for several modems provided the Downstream frequencies and the Upstream Channel ID are the same (i.e., same “profiles”). The WMTS E1/T1 configuration needs to be modifed appropriately for every E1/T1 modem installed on the network. This is done using the Java™-based Vyyo Configuration tool. This tool configures the E1/T1 port on the modem to be connected (“bound’) to the correct E1/T1 port on the E1/T1 card plugged into the WMTS.
2.6 Configuration Tools and Files Matrix Tool Configured File or Device Description CMconfigurationFileEditor Modem Configuration file (e.g., “MIC_xxx.cfg”, where xxx is some unique number.) This file downloads to a modem during the registration process. It contains all the parameters required for the modem’s operation in the DOCSIS network: upstream and downstream frequencies, QoS, etc. It is also call the modem “boot” file. XmtsConfigurationFileEditor Regtree.
Vyyo Configuration Tool WMTS MIB database This is a standalone JAVA based tool that can be accessed from the NMS. It is used to modify and configure the WMTS operating parameters. NMS (Castlerock) WMTS or Modem MIB values (Typically for viewing only.) A general purpose Network Management System for operating the network; also used to launch the Vyyo Configuration tool. Any ASCII text editor, e.g., Notepad CM.
Chapter 3. The Modem Initialization Process To understand the configuration process, it is useful to understand the detailed steps the modem goes through during its initialization. When the modem is first powered up, it must go through a fixed sequence of steps before it can exchange data with the network. To be successful, this requires the modem and the WMTS to be configured with various parameters.
3.1.2 Downstream Synchronization The modem listens for downstream transmissions from the WMTS (which are broadcast at frequent intervals for exactly this purpose) according to its pre-configured or default frequency plan. This may be a single fixed frequency or a sequence of frequencies, depending on the Network RF Plan and/or the internal programming of the modem.
3.1.6 Establish Time of Day The modem uses the ToD server address(es) just received to send a Time of Day request to the ToD server(s). This is combined with the time offset received in the DHCP response to calculate the current local time. The Time of Day is used by both the modem and the WMTS to timestamp logged events (accessible via the Network Management System). 3.1.
Chapter 4. Overview of the WMTS and Modem Configuration This section provides an overview of the steps and tools necessary to configure both sides of the communications link (WMTS and modem) required to add a data modem or the data portion of a new E1/T1 modem to the network. Several different tools and files are used as described below. 1. Make sure that the three required servers are installed and operational: DHCP, ToD and TFTP. For details see Chapter 8, Installing Vyyo Servers for WMTS Operation.
6. . NOTE 1: Five T1s per 3.2MHz upstream channel using 16QAM modulation is the hard limit for the current system. Attempting to configure more T1s on an upstream channel than it can support will cause the modem initialization to fail. Consult your system engineer for advice on the maximum number of modems per upstream channel ID. 7. Use the appropriate DHCP tool for your system to bind the modem’s MAC address to its IP address and modem configuration file. If ipLease is used, edit and compile the CM.
11. If the modem is already on and its modem configuration file has been changed (to bind the E1/T1 ports), then the modem must be rebooted; although this happens automatically when the DHCP lease expires, it is more efficient to simply power cycle the modem (unplug and replug the power connector or switch the modem OFF then ON) to restart the modem initialization sequence. 12.
Chapter 5. Adding a Modem to the WMTS NOTE: These instructions are required for all modems. If you are adding a T1 modem then you must also perform the step in Chapter 6, Configuring a T1 Connection to finish the installation. Use the instructions in this chapter to setup a data modem or the data portion of an E1/T1 modem and configure the WMTS to communicate with it over IP. This chapter covers the following topics: 1. Section 5.
System Configuration Guide 3. DHCP Settings for the ModemSection 5.3 Configuring the WMTS describes how to configure the WMTS upstream, downstream and QoS parameters. This is done using the Vyyo Configuration Tool. Instructions for performing these changes are shown in Configuring the WMTS. 4. Section 5.4 Setting the Modem’s Downstream Frequency describes how to set the modem downstream initial receive frequency via the modem’s internal Telnet server. 5. Section 5.
System Configuration Guide Right-click on “Upstream Channel ID” and select “MODIFY” to display the popup window in which you may set the value of the Upstream Channel ID. Note: The detailed parameters for each upstream channel must be set in accordance (see Setting the Upstream Channel)with the overall Network RF Plan – contact your system engineer for assistance. The Channel ID is the identifier for the physical RF port on the RF cards plugged into the rear of the WMTS.
System Configuration Guide Figure 5-1: Setting Upstream Channel ID www.vyyo.com Adding a Modem to the WMTS – p.
System Configuration Guide 5.1.2 Setting the Downstream Frequency In the following example, the Downstream Frequency is changed to 743 MHz. 1. From the main screen shown below select “General Parameters” and then choose “Downstream Frequency”. 6. Right-click on “Downstream Frequency” and select “MODIFY” to display the popup window in which you may set the value of the downstream frequency in Hertz (note the six zeroes). NOTE: This value will be specified by your system engineer.
System Configuration Guide 5.1.3 Setting Concatenation and Fragmentation Capabilities 1. Select “Modem Capabilities” and enable “Concatenation” and “Fragmentation” by setting them to “1” (select each one then right-click to view the “Set Value” dialog box, enter the value “1” then click “OK”). NOTE: These should always be used unless specified otherwise by your system engineer. Figure 5-3. Setting the Concatenation Value Figure 5-4. Setting the Fragmentation Value www.vyyo.
System Configuration Guide 5.1.4 Setting Upstream QoS (Class of Service) for IP Data 1. Select “Class of Service Parameters” 2. Right-click on “Maximum Upstream Rate” to display a selection of QoS profiles. 3. Choose the profile that is appropriate for the installation being done. Your system engineer can provide assistance based on the Network RF & IP Plan. 4. Select a profile in the left side of the popup window to display its corresponding parameters on the right side. Figure 5-5.
System Configuration Guide 5.1.5 Setting Additional Downstream and Upstream Channels Use the “Vendor Specific Parameters” option to set additional downstream frequencies and upstream channels. Your system engineer should tell you if this is necessary. First enter the Frequency of the Additional Downstream Channel in Hertz and then enter the associated upstream channel ID (ID of additional Upstream channels).
System Configuration Guide 5.1.6 Setting the Maximum Number of CPEs It is advisable to set the maximum number of CPEs at this time by selecting and entering the desired value on the following screen: Figure 5-7: Setting the maximum number of CPEs www.vyyo.com Adding a Modem to the WMTS – p.
System Configuration Guide 5.2 DHCP Settings for the Modem The DHCP Server provides the IP address for the modem and also specifies which modem configuration file will be downloaded to the modem. In the following two sections, instructions are provided for setting up two different DHCP Servers: the ipLease DHCP Server and the Windows 200x Server Edition DHCP Server. Either of these (or any other) DHCP server may be used (but not multiple ones at the same time). 5.2.
System Configuration Guide 3. This section of CM.SRC shows IP addresses of all the servers and their associated parameters. See the comments on each line of the file shown for details. Your system engineer can tell you how to configure these addresses. Figure 5-9: Server Configuration Info on CM.SRC file www.vyyo.com Adding a Modem to the WMTS – p.
System Configuration Guide 4. In the [Hosts] section of CM.SRC shown below, four modems are defined. You may add additional modems here. If they are not defined here they will be ignored in the next section. Four modems are defined and named in the [Hosts] section of this file. Figure 5-10. CM.SRC File Format 5. Add the configuration parameters for each modem as shown below. Note that even though each modem has a unique bpBootFile filename this is not typical. This file is the modem’s configuration file.
System Configuration Guide Each modem name is defined in square brackets and followed by its MAC address “Chaddr”, its “StaticIPAddress” and it “bpBootFile” name (this is also known as its modem configuration file.) Figure 5-11. Defining and Naming Installed Modems NOTE: This file (CM.SRC) must be compiled by executing the command “dhcpgen cm” from the directory in which the file is located. Before compilation, the DHCP Server must be shut down.
System Configuration Guide Click this button Figure 5-12: DHCP Server Shutdown in ipLease™ www.vyyo.com Adding a Modem to the WMTS – p.
System Configuration Guide 7. Now change directories to the ipLease directory (in a DOS window) and type “dhcpgen cm” to generate the machine-readable files for the ipLease DHCP server. The output should indicate “successful” as shown below. If not, check to make sure you have shutdown the iplease server or that you have not mistyped something in the CM.SRC file. 8. Restart the ipLease server.
System Configuration Guide Figure 5-13: Navigate to the DHCP program 2. Expand the tree in the left window pane and expand “Reservations” to view all the modems to which DHCP is leasing IP addresses www.vyyo.com Adding a Modem to the WMTS – p.
System Configuration Guide Figure 5-14: Expand “Reservations” 3. Now click “New Reservation” on the “Action” menu (or right-click on “Reservations” and select “New Reservation”) www.vyyo.com Adding a Modem to the WMTS – p.
System Configuration Guide Figure 5-15: Make a “New Reservation” using DHCP www.vyyo.com Adding a Modem to the WMTS – p.
System Configuration Guide 4. Enter the required information (see your system engineer for details) and click the “Add” button. NOTE: Make sure to select the “DHCP only” radio button under “Supported Types”. Figure 5-16: Enter the information for the new reservation www.vyyo.com Adding a Modem to the WMTS – p.
System Configuration Guide 5. Now select the new reservation and right-click on the newly added modem then select “Configure Options” to choose the modem configuration file that will be downloaded to this modem. Observe that five Options are shown in the right pane of the main window. These are the default values.: Figure 5-17: Navigate to the “Configure Options” action www.vyyo.com Adding a Modem to the WMTS – p.
System Configuration Guide 6. Select the “General” tab in the popup window, scroll down to item “067” and check (and select) the “Bootfile Name” checkbox to enter or change the “boot” or modem configuration file name. NOTE: Any of the other options may be changed using this same procedure. These values must match the physical setup of the network (as per the Network IP and Network RF plans) to make the system work. If this DHCP server is already in operation the default values should be correct.
System Configuration Guide TIP: You may verify that the modem properties have been set correctly. Select the modem and right-click to display the action popup window; then select “Properties” to display and allow you to verify the modem information entered previously. Figure 5-19: Navigate to the Properties display for the selected modem www.vyyo.com Adding a Modem to the WMTS – p.
System Configuration Guide Tip: The modem information is displayed in this popup window. Figure 5-20: View the Properties for the selected modem www.vyyo.com Adding a Modem to the WMTS – p.
System Configuration Guide 5.3 Configuring the WMTS NOTE: Before you can perform this procedure you must have previously edited the regtree.txt file, compiled it and downloaded it to the WMTS to set its IP address. See Chapter 7. Setting the WMTS IP Address. This section assumes that you have previously installed NMS Version 7. See Installing and Uninstalling the NMS for brief instructions. The upstream and downstream channels of the WMTS must be configured before a modem can communicate with the WMTS.
System Configuration Guide Set this to ‘up” to operate this channel or “down” to turn it off This WMTS upstream channel will receive on this frequency The modem transmits on this frequency These are the WMTS downstream channels associated with this WMTS upstream channel Check this box Click here to save the new settings Figure 5-21: Selecting and Setting Upstream Channel Parameters Check this box unless your System Engineer indicates otherwise NOTE: For Data Service Type, “Best effort channel” or “CIR
System Configuration Guide 7. Click on the Update button at the bottom left of the screen to save the new settings. Click ”OK” when the folllowing confirmation popup window appears. Figure 5-22: Confirm the Update 8. You have now completed configuring the upstream channel. For a summary of all of the upstream channels click on the “Upstream” item in the left pane of the window. Figure 5-23: Viewing the WMTS Upstream Channels Summary www.vyyo.com Adding a Modem to the WMTS – p.
System Configuration Guide 5.3.2 Setting the WMTS Downstream Parameters 1. Select the WMTS Downstream Channel you wish to configure from the left side of the window. In this example downstream channel 1 is selected and all of its parameters are displayed in the right pane of the window. Bandwidth, modulation, and other parameters can be changed. Typically the default values should be used with “Optimize channel parameters” unless your system engineer indicates otherwise.
System Configuration Guide 9. To permanently save the configuration to the WMTS click on the “Update” button. Press the “OK” button on the popup window to confirm the update. Figure 5-25: Confirm the Update 10. You have now completed configuring the downstream channel. For a summary of all the downstream channels click on the “Downstream” item in the left pane of the window. Figure 5-26: Viewing the WMTS Downstream Channels Summary www.vyyo.com Adding a Modem to the WMTS – p.
System Configuration Guide 5.4 Setting the Modem’s Downstream Frequency This section provides details on how to set the downstream frequency that the modem listens on to begin its initialization sequence. Setting this value greatly reduces the time it takes for a modem to complete its initialization sequence. NOTE: the downstream frequency that is set using this technique will not be saved in the modem until the modem completes registration. 1.
System Configuration Guide Enter the user password here when prompted. Figure 5-27: Log In to the Vyyo WMU Telnet Server www.vyyo.com Adding a Modem to the WMTS – p.
System Configuration Guide 5. This screen will be displayed after the password is correctly entered: Figure 5-28: Successful Telnet Login www.vyyo.com Adding a Modem to the WMTS – p.
System Configuration Guide 6. Type “su operator”, then press return. Now enter the operator’s password (obtain this from your system engineer or a Vyyo representative) to access the DOCSIS control commands. Note: Return to user mode from operator mode at any time by typing “su user” – no password is required to return to user mode. Enter the operator password here when prompted Figure 5-29: Switching to the Operator's Permission Level www.vyyo.com Adding a Modem to the WMTS – p.
System Configuration Guide 7. Change to the DOCSIS Control subdirectory by typing “cd docsis”: Type “cd docsis” here Figure 5-30: The “cd docsis” Command www.vyyo.com Adding a Modem to the WMTS – p.
System Configuration Guide 8. Type “goto_ds xxxxxxxxx” to set the Downstream Frequency, where “xxxxxxxxx” is the frequency in Hertz. NOTE: Your system engineer should provide you with this value. This will now be the permanent fixed frequency at which the modem will listen for a broadcast from the WMTS. After a maximum of 30 seconds, the modem LEDs should light up and remain lit.
System Configuration Guide 9. To view the “operator” commands type “?”. The following figure shows the “operator” commands. NOTE: to get help on a particular command type “help ” Figure 5-32: Executing the “?” command to view the Operator commands www.vyyo.com Adding a Modem to the WMTS – p.
System Configuration Guide 5.5 Verifying the Modem Downstream and Upstream Status 1. View the downstream status after the modem has successfully completed registration by typing “dsdiag” to verify that the change took effect and the modem is operating correctly: “QAM = LOCKED” and “FEC = LOCKED” should appear as the last two lines. You must have “operator” access rights to do this. NOTE: this will only happen if the modem is in a place where it can establish RF connectivity to the WMTS, e.g.
System Configuration Guide 2. View the Upstream Status after the modem has successfully completed registration by typing “usdiag” to verify that the modem is operating correctly. The parameters should be stable. You must have “operator” access to do this. Type “usdiag” here Figure 5-34: Viewing the Modem Upstream Status The modem has now established IP connectivity with the WMTS. www.vyyo.com Adding a Modem to the WMTS – p.
System Configuration Guide 5.6 Using an HTTP Connection to View Modem Operation You may also view this information using an HTTP browser such as Internet Explorer. All modems include an HTTP server at the same address as the Telnet server. If the modem does not yet have an IP address assigned and operating (i.e., completed registration), set your browser to browse the URL http://192.168.100.1/ to get the status information.
System Configuration Guide 12. Obtain the Operator user name and password from your System Administrator or an authorized Vyyo representative. Enter the user name and password in the appropriate fields, and click the OK button. The Vyyo Connection page opens. Figure 5-37: Entering the modem user name and password www.vyyo.com Adding a Modem to the WMTS – p.
System Configuration Guide 13. Each informational page consists of two sections: A Menu box at the left, which enables you to navigate between pages, and a Data area at the right, which shows information specific to the system. 5.6.2 Viewing the Connection Page To view the Connection page click the “Connection” option on the Menu box. Figure 5-38: Selecting the Browser Connection option www.vyyo.com Adding a Modem to the WMTS – p.
System Configuration Guide The browser displays the Connection page which has five areas of information: • Startup Procedure • Downstream Channel • Upstream Channel • Assigned IP Address of the Modem • Current System Time from the ToD Server. Figure 5-39: Viewing the Browser Connection page 5.6.3 Viewing the Software Page To view the Software page click the Software option on the Menu box. Figure 5-40: Selecting the Browser Software option www.vyyo.com Adding a Modem to the WMTS – p.
System Configuration Guide The Software page displays modem Information and Status data. Figure 5-41: Viewing the Browser Software page 5.6.4 Viewing the Security Page To view the Security page click the Security option on the Menu box. Figure 5-42: Selecting the Browser Status option The browser displays the Security page. You use the Security page if you wish to change your login password.
System Configuration Guide Chapter 6. Configuring a T1 Connection NOTE: the data connection for the E1/T1 modem must be setup as previously described in Chapter 5, Adding a Modem to the WMTS Three separate tools are necessary to configure a T1 connection: The CMConfigFileEditor is used to set the modem QoS (also referred to as Class of Service) in the modem configuration file downloaded during the modem initialization phase.
System Configuration Guide 6.1 Configure the Modem for T1 Operation In this section instructions are provided for using the CMConfigFile Editor to edit the modem configuration file which will be downloaded to the modem. When the edits on the following pages are complete, copy or move the modem configuration file to the directory being used by the TFTP Server (usually this will be something like “C:\vyyo\mic”).
System Configuration Guide 4. Set the upstream channel ID using the same procedure. This is the channel ID the modem will use to transmit upstream data to the WMTS. The channel ID parameters are sent by the WMTS when it broadcasts UCDs during the Obtaining Upstream Parameters phase (immediately after the Downstream Synchronization phase) of the modem initialization prcocess. This procedure for configuring the downstream channels is described in Setting the WMTS Upstream Parameters. Figure 6-2.
System Configuration Guide 5. Create a second Class of Service (aka. QoS or Service ID). Select and right-click “Class of Service”, then select the “Duplicate” option. This is necessary to add the “Voice” (or “WAN”) service for the T1 connection. NOTE: the first Class of Service was created previously for the data only connection. This second Class of Service is specifically for the T1 connection so make sure it is setup that way. The same upstream channel is used for both. Figure 6-3.
System Configuration Guide 6. Observe that a second Class of Service has been added in the left column of the window. 7. Select this second Class of Service, then right-click on the Maximum Upstream Rate parameter and select “Modify” from the popup menu. Figure 6-4. Modifying the Upstream Bit Rate Value www.vyyo.com Configuring a T1 Connection – p.
System Configuration Guide 8. Now select “WAN Service/2048k” from the “Parameter” pane of the popup window. Figure 6-5. Choosing an Upstream Bit Rate Parameter 9. The corresponding parameters will appear on the right side of the popup window. www.vyyo.com Configuring a T1 Connection – p.
System Configuration Guide 10. Now select “WAN Service/2048K” in the left pane of the popup window and then Click the “OK” button. Figure 6-6. Choose Profile Setting 11. The display will return to the main window showing the new values set above, as shown in Figure 6-7. Figure 6-7. www.vyyo.com Configuring a T1 Connection – p.
12. Select “Modem Capabilities” and turn on “Concatenation” and “Fragmentation” by setting them to “1” (select each one then right-click to popup the “Set Value” window) and clicking the “OK” button. Figure 6-8. Setting Concatenation Value Figure 6-9.
Vyyo Installation Guide 13. The display will return to the main window. The modem configuration file is now configured for T1 operation. You should save this file. This filename will be bound to the modem MAC address using the DHCP Server tool as described in IpLease DHCP Server: Editing and running the CM.SRC File. The same modem configuration file may be used for several modems provided the Network RF Plan allows for this; see your system engineer for details. Figure 6-10.
Vyyo Installation Guide 6.2 Adding the T1 modem to the WMTS T1 Interface and Assign Port(s) NOTE: The WMTS Upstream and Downstream parameters must be configured prior to performing this procedure. In particular the Upstream “Voice Service Type” must be set to “WAN” for an E1/T1 channel. See Configuring a T1 Connection. This is done using the Vyyo Configuration Tool. Before proceeding, launch the Vyyo Configuration Tool as described in Launching the Vyyo Configuration Tool. 1.
Vyyo Installation Guide 2. Select the “Insert” menu option and choose “Modem” Figure 6-12: Insert Modem 3. A popup window will appear to allow you to enter the modem type. From the pulldown menu select “E1/T1 Modem”. Figure 6-13: Select E1/T1 Modem 4. Confirm your selection Figure 6-14: Confirm modem selection www.vyyo.com Configuring a T1 Connection – p.
Vyyo Installation Guide 5. A new modem icon will appear on the WMTS tree window pane. Enter the last three bytes of the Vyyo modem MAC address and press the “Update” button then press “OK” on the popup window which confirms the “success” of the update. Note: The first three bytes of the Vyyo MAC address (the vendor ID) are displayed both in the navigation tree on the left and in the data entry window on the right.
Vyyo Installation Guide 6. Enter the desired modem parameters and add the E1/T1 configuration for the modem by clicking on the “Add E1/T1 Link” button. You may cross connect an E1/T1 modem to another E1/T1 modem – see Appendix E: Vyyo Configuration Tool – Additional Functions for this procedure. NOTE: Do this process once for the V311 modems and twice for the V312 modems (the latter have two active E1/T1 ports).
Vyyo Installation Guide 7. When this screen appears, select the desired port on the WMTS E1/T1 interface card using the drop-down menu. This binds the T1 port on the modem to its corresponding T1 port on the WMTS E1/T1 interface card (inserted into the rear of the WMTS chassis). Other parameters may be changed from the defaults shown in this screenshot to create a “fractional T1” connection: the Framing parameter must be set to ESF Framing or D4 Framing, and then you may set the desired Time Slots range.
Vyyo Installation Guide 8. Now click on the “Update” button and press “OK” when the confirmation popup window appears. Select “Refresh Modems” from the File menu to refresh the modem icons (the new modem icon should change to green). Figure 6-19: Updating the system for the new modem www.vyyo.com Configuring a T1 Connection – p.
Vyyo Installation Guide 9. This screen will show the new modem and its connection to WMTS port 1 (in the Connections Table at the bottom). Note that the color of the modem in the left window pane has now changed from red to green (if the modem is online). Figure 6-20: Viewing the new modem’s E1/T1 interface information www.vyyo.com Configuring a T1 Connection – p.
Vyyo Installation Guide 10. For a summary of all modems and E1/T1 ports select the “E1/T1 Interfaces” item on the navigation tree in the left window pane Figure 6-21: Viewing the E1/T1 Interfaces At this point you have successfully connected the E1/T1 modem to the system and data should be flowing between the modem and the WMTS. www.vyyo.com Configuring a T1 Connection – p.
Vyyo Installation Guide Chapter 7. Setting the WMTS IP Address Note: Prior to performing this procedure the WMTS must be connected to the “download” computer serial port via the lower COM port (COM2) on the WMTS Control and Forward card. The WMTS must also be connected to the same LAN subnet as the computer using its RJ45 connector on the same (Control and Forward) card.
Vyyo Installation Guide • WMTS IP address • Gateway computer (used for downloading) IP address • Gateway computer subnet mask • IP addresses of any other computers that are permitted to access the WMTS remotely 2. Change the “CmtsIPAddress” as desired: this is the WMTS’s permanent IP address which will be downloaded later using the XmtsConfig tool. 3.
Vyyo Installation Guide Figure 7-1. Regtree.txt File Contents www.vyyo.com Setting the WMTS IP Address – p.
Vyyo Installation Guide 5. Now compile regtree.txt by executing SETIP.bat which should be in the same directory as regtree.txt. SETIP.bat is a batch file that converts regtree.txt from text to a special format read by the WMTS. The resulting file will be named RegTree.rtr. Figure 7-2. Setip.bat www.vyyo.com Setting the WMTS IP Address – p.
Vyyo Installation Guide 6. Locate the Regtree.rtr file and copy it to the directory (download path) that is used by the TFTP server to get the requested download files (the download directory): Figure 7-3. Regtree.rtr Location in TFTP Root Directory www.vyyo.com Setting the WMTS IP Address – p.
Vyyo Installation Guide 7. Open the TFTP server: in this example we use Pumpkin.exe. You may bring up the Options dialog window by clicking on the “Options” button. This will allow you to change the download directory. Note:The file RegTree.rtr must be copied to the TFTP server download path, “C:\Vyyo\mic” as shown in this example since this is the directory where the TFTP server finds the requested files to be downloaded. You may change this path to suit your particular directory layout.
Vyyo Installation Guide Note: Observe that RegTree.rtr has been copied to the TFTP download directory (C:\Vyyo\mic) used in this example: Figure 7-5. Regtree.rtr, Located in TFTP Root or Specified Download Directory www.vyyo.com Setting the WMTS IP Address – p.
Vyyo Installation Guide 8. Open the XmtsConfig.exe tool to perform the download to the WMTS. This tool is typically located in the “…\Tools\XmtsConfig” directory of the released software. 9. When the initial window appears right-click to expose a popup window from which you must select “Activate”. 10. This will enable the screen for one minute, after which you must repeat this procedure to re-activate the screen. The one minute timeout prevents accidental downloads and restarts.
Vyyo Installation Guide 11. After activating this application select ‘Connect’. This will open a second small window within which you can choose the type of connection to open (Serial or IP). Figure 7-7: The “Connect” button 12. Select ‘Serial’ and the appropriate computer ‘Com’ port number to which the WMTS is connected. Click on ‘Open Port’ then select ‘Close’ to close the small window and return to the main application window. Figure 7-8: Making the serial connection www.vyyo.
Vyyo Installation Guide 13. Now enter the TFTP Server IP Address, Subnet mask and Default Gateway. Click the corresponding buttons as you set each of these. Observe that the caption at the top of the XmtsConfig tool indicates “Connected: Com 1” at this time since it is connected via the serial connection. After the IP address has been set, the caption will change to “Connected: Remote 10.10.10.202” in this example (see the next step) to indicate that the LAN connection is active.
Vyyo Installation Guide 14. Now enter the filename “regtree.rtr” in the “Version File” window, then click the “Start Software Download” button. Recall that the regtree.rtr file must be in the TFTP download directory as described in the first part of this procedure. The message below is displayed after the download command is sent to the WMTS – it does NOT indicate that the download has occurred. To confirm the download you must observe the indicator LEDs on the WMTS: they should be flashing with activity.
Vyyo Installation Guide Figure 7-11. TFTP Download Message 15. You have now completed downloading the Regtree file containing the permanent configuration settings for the WMTS. www.vyyo.com Setting the WMTS IP Address – p.
Vyyo Installation Guide 16. The message in the following figure should display after the System Restart message is sent. Figure 7-12. System Restart Message Note: The XmtsConfig application does not report if the action is successful, only that the command has been sent. 17. To verify that the download has taken effect you must use the procedure described in Appendix B. Checking the WMTS Version. www.vyyo.com WMTS US Port Mapping – p.
Vyyo Installation Guide Chapter 8. Installing Vyyo Servers for WMTS Operation Three servers must be installed before operating the WMTS system. These servers are in accordance with the DOCSIS standard. 1. Time of Day server 2. TFTP server 3. DHCP server On the computer connected to the WMTS there is folder named c:\vyyo\servers. This software was part of the original software installed from the installation CD. See your system engineer or Vyyo representative for assistance if necessary.
Vyyo Installation Guide 2. Start the application pumpkin.exe Figure 8-2. Pumpkin Folder Location 19. Click OK and follow the instructions on screen to install the TFTP server. 20. When done, go to StartProgramsAccessoriesKlever CoPumKin Figure 8-3. Location of PumpKIN After Installation www.vyyo.com WMTS US Port Mapping – p.
Vyyo Installation Guide 21. The following window appears after the application has started: Figure 8-4. PumpKIN Status Window 22. Select Options Figure 8-5. Options Dialog Box www.vyyo.com WMTS US Port Mapping – p.
Vyyo Installation Guide 23. Change TFTP filesystem root (download path) to where your modem configuration file will be located. In our case it will be under c:\vyyo\mic. 24. Make sure to select “Read Request Behavior and Write Request Behavior” to Give/Take all files. 25. Click OK 26. You may close this window as Pumpkin will continue to run in the background. The Pumpkin icon will appear on the taskbar (usually at the bottom of the screen) – click on it to bring up the Pumpkin window. 8.
Vyyo Installation Guide Figure 8-6. DHCPSVR.ini File 1. Set the computer’s DHCP server IP address in the ServerIPAddr= field. 27. Set your network identification in the SubnetNum=xx.xx.xx.xx field. 28. Save this file after completing your changes 8.3.2 cm.src The cm.src file maps the modem MAC address to an IP address and binds the modem MAC address to a specific modem configuration file. It also provide the default addresses for the gateway, TFTP server and ToD server.
Vyyo Installation Guide Figure 8-7. CM.SRC File Format www.vyyo.com WMTS US Port Mapping – p.
Vyyo Installation Guide Figure 8-8. CM.SRC File Format (Continued) 1. Comments in the cm.src file are annotated with */ 2. After editing the cm.src file, save your changes. 8.3.3 Dhcpgen Note: Your computer must be configured with the correct IP address, i.e., the same one as in the dhcpsvr.ini file. (10.10.10.1in this example) before using dhcpgen 1. cm.src must be compiled with dhcpgen for use with the IPLease DHCP server. Dhcpgen must be run in a DOS window. 2. On the Start Menu, choose Run… 3.
Vyyo Installation Guide Figure 8-9. The Run... Dialog Box 29. Navigate to the IPLease folder by executing the following command: cd \; cd vyyo; cd servers; cd iplease Figure 8-10: Navigating to the iplease directory www.vyyo.com WMTS US Port Mapping – p.
Vyyo Installation Guide 30. Type dhcpgen cm and press the Return or Enter key. The second parameter is the name of the .src file the dhcpgen will convert (compile) into a format usable by the DHCP server (this is called the ipLease format). The second to last line informs you if the it has completed successfully. If the compilation reports an error you must re-edit the CM.SRC file and recompile it and repeat this process until it executes successfully. Otherwise the DHCP will not be using the correct data.
Vyyo Installation Guide 31. To shutdown the iplease server click on the Shutdown button in the upper right window pane of the application as shown below: 32. Figure 8-12: ipLease Server Shutdown 8.3.4 DhcpSvr: After completing section 6.3.3, open the IPLease folder and start DhcpSvr.exe. The ipLease application window will be the same as in Figure 8-12 above. www.vyyo.com WMTS US Port Mapping – p.
Vyyo Installation Guide Chapter 9. Maintenance and Troubleshooting 9.1 Introduction The WMTS is an IP centric two-way RF system, which incorporates various information technologies and RF devices. When the system is not operating properly, the malfunction must be isolated to localize the problem to a single functional area. The troubleshooting process consists of three basic steps: • • • Identifying the problem, Diagnosing the problem, and Implementing a solution.
Vyyo Installation Guide Use a spectrum analyzer and RF power meter to perform tests. A typical basic RF setup is illustrated in Figure 9-1. Please use the specific block diagram for your system when you are troubleshooting problems 9.2.2 Checking the Downstream Perform the following steps to isolate a problem on the downstream channel of the RF frontend: a.
Vyyo Installation Guide 9.2.3 Checking the Upstream Perform the following to isolate a problem on the upstream channel of the RF frontend: Measure the output power of the downconverter. Use a spectrum analyzer tuned to the upstream channel IF (about 44 MHz), with a span of 20 MHz. The following diagram illustrates a basic RF test setup.
Vyyo Installation Guide Chapter 10. Troubleshooting The Subscriber Site 10.1 Post-Registration Verification When the modem registration process has reached completion, connect the Laptop or PC to the V280 WMU and verify the following items: Verification Item Task 1 Check the IP address. From the Windows Command Prompt, ipconfig or winipcfg to view the configuration. Open the Web Browser and verify that there is proper Internet access. 2 Perform relevant system speed verification tests.
Vyyo Installation Guide Use the following steps to troubleshoot the IF layer: Verification Item Task Signal amplitude Connect the SLM to the IF input cable. Set the SLM to the appropriate known DS frequency and measure the amplitude in dBmV. Verify that the peak amplitude of the IF signal is compliant with the WMU input signal level specification. If no signal is present, verify that the radio transceiver was installed according to the manufacturer’s installation procedures.
Vyyo Installation Guide 10.5 Repairs Safety 1. Repairs of WMTS should take place only in VYYO company service laboratories or in other VYYO formally approved distributors service laboratories. In case of field handling our general SAFETY warning is to disconnect the unit from power supply for safest repair. 2. In case of a -48VDC operated WMTS, the External Circuit Breaker (Du Pole) must be used before connection/removal of the power cable to/from the WMTS. www.vyyo.com WMTS US Port Mapping – p.
Vyyo Installation Guide Appendix A. Mapping WMTS US Port The following figure shows a rear view of the WMTS with several upstream RF cards. The numbering proceeds from right to left and allows for eight channels on each card even if the card does not have eight physical connections. Logical ports are also referred to as “interfaces”. NOTE: the downstream port mapping is similar except that the first Logical Port is number 2. www.vyyo.com WMTS US Port Mapping – p.
Vyyo Installation Guide Appendix B. Version Checking the WMTS The version number may be easily checked by using the XmtsConfig tool shown in the figure below: right click on any open area in the main window to display the popup shown, and then click on “Activate” followed by “Connect”. This establishes communication between the XmtsConfig tool and the WMTS. Now click on “Version Check (WMTS)” in the popup window. See Setting the WMTS IP Address for instructions on using the XmtsConfig tool. 1.
Vyyo Installation Guide 33. Now click on “Connect” in the main window and when the popup menu appears, verify or set the IP address as needed, and click on “Connect” then “Close”. A message will appear in the main window indicating if the connect command was sent. NOTE: the “Activate” command automatically closes the WMTS connection after approximately 60 seconds – this may cause a message like “Inconsistent WMTS Version” to appear in the message window.
Vyyo Installation Guide 34. Right click in the open space in the main menu to bring up the popup menu and select “Version Check (WMTS)”. The WMTS version will be shown in the message window. Figure B-3: Viewing the WMTS Version www.vyyo.com Checking the WMTS Version – p.
Vyyo Installation Guide Appendix C. Installing and Uninstalling the NMS C.1 First Time Installation Follow the steps below to install the NMS. See the NMS SNMPc Version 7.0 Reference Guide for detailed instructions: Unzip the installation ZIP file Launch INSTALL.CMD When Java is installed choose "Typical" (use defaults) On SNMPc-7 installation choose: - Server - No Discovery Seed - Check the "Start with discovery off" Note: When using Windows XP, you must extract the installation zip file.
Vyyo Installation Guide C.4 Uninstalling the NMS The main steps in uninstalling the NMS based on SNMPc 7.0 are as follows. See the NMS SNMPc Version 7.0 Reference Guide for detailed instructions: 1. Shutdown the SNMPc manager 2. Stop the Data Collection Service 3. Shutdown the SNMPc NMS 4. Shutdown the SNMPc Server 5. Remove the SNMPc application 6. Remove Java™ Runtime Environment if desired 7. Reboot www.vyyo.com Installing and Uninstalling the NMS – p.
Appendix D. Launching the Vyyo Configuration Tool The Vyyo Configuration Tool is used to configure the WMTS and there are two ways to launch the Vyyo Configuration Tool. You may use either one, depending on whether or not the NMS (SNMPc) is up and running. If you just need to configure the WMTS it is easier to launch the Vyyo Configuration Tool from the Windows “Start” menu.
Vyyo Installation Guide D.1 The Vyyo Configuration Tool Menu (exploded view) The following exploded view of the Vyyo Configuration menu shows all the main menu options and their second level options. D-1: The Vyyo Configuration Tool Menu (exploded view) www.vyyo.com Launching the Vyyo Configuration Tool – p.
Vyyo Installation Guide D.2 Launching the Vyyo Configuration Tool from the “Start” Menu 1. From the “Start” menu select and click on “Configure WMTS” Figure D-2: Using the “Start” menu to launch the Vyyo Configuration Tool 35. You must now add the WMTS by selecting the “Insert” menu option then choosing “WMTS” from the drop down menu Figure D-3: Adding (Inserting) the WMTS 36. Insert the WMTS IP address and click “OK” Figure D-4: Inserting the WMTS IP address www.vyyo.
Vyyo Installation Guide 37. The Vyyo Configuration Tool will now read data from the WMTS based on the IP address you entered in the previous step Figure D-4: Reading the WMTS Data 38. Fully expand every level of the WMTS tree to show all the components that may be configured. You may later collapse the tree to display only those with which you are currently working. Figure D-5: Expand the WMTS Tree www.vyyo.com Launching the Vyyo Configuration Tool – p.
Vyyo Installation Guide 39. This is the fully expanded WMTS tree: you have now launched the Vyyo Configuration Tool and may proceed to perform any of the WMTS configuration procedures Figure D-6: Fully expanded WMTS tree www.vyyo.com Launching the Vyyo Configuration Tool – p.
Vyyo Installation Guide D.3 Launching the Vyyo Configuration Tool from the NMS 1. If the NMS is not started, launch it from the “Start” menu Figure D-7: Launching the NMS from the “Start” menu 2. Expand the Root Subnet tree and the WMTS one level beneath it to reveal an icon and name for the particular WMTS you wish to configure. In this image the WMTS is named “The_WMTS_at_XXX”. Select and double-click on this WMTS name to open it.
Vyyo Installation Guide www.vyyo.com Launching the Vyyo Configuration Tool – p.
Vyyo Installation Guide 3. When the picture of the WMTS appears select the “Vyyo WMTS” main menu item and then choose the “Configure” option from the drop down menu. This will launch the Vyyo Configuration tool. The WMTS IP address is automatically passed to the Vyyo Configuration tool if you use this method to launch it. You may now proceed from step (5) of the previous section D.
Appendix E: Vyyo Configuration Tool – Additional Functions E.1 Adding an E1/T1 Cross Connection E.
Vyyo Installation Guide INDEX [Hosts] in CM.SRC ...................................... 43 Additional Channels, Setting....................... 38 Castlerock SNMPc ...................................... 79 Checking the WMTS Version.................... 137 CM.SRC....................................................... 40 CmtsIPAddress........................................ 100 CmtsSubnetMask .................................... 100 Concatenation and Fragmentation, Setting the..................................