Installation Instructions

ManualsBrandsvyncs ManualsElectronics4G OBD

FCC Regulations:

 This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference

that may cause undesired operation.

 This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

—Consult the dealer or an experienced radio/ TV technician for help.

 Changes or modifications not expressly approved by the manufacturer could void

the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. To comply with FCC RF Exposure compliance

requirements, this grant is applicable to only Mobile Configurations. The antennas

used for the transmitter must be installed to provide a separation distance of at least

Summary of content (8 pages)

PAGE 1
FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
PAGE 2
0cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
PAGE 3
1.Hardware features NO ITEM .
PAGE 4
2. Hardware description 2.
PAGE 5
2.2 OBD connector pin out Pin# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Comment NC J1850_BUS+ NC GND GND HS_CAN_HI K-LINE NC NC J1850_BUSNC NC NC HS_CAN_LO L-LINE Battery voltage 2.3 Insert the SIM card The notch of the SIM card faces outwards.
PAGE 6
3. Account Creation and Verify Device process 1. Go to http://vyncs.com. 2. Hover your cursor over LOGIN at the top of your screen and click on CONSUMER in the drop down menu. 3. If you have purchased the device from vyncs.com and already created an account, type in your username and password that you chose and click on “Log in”. Note that both username and password are case sensitive.
PAGE 7
4. Installation and Ativation procedures 1. Make sure vehicle is in open view of the sky. Parking garages and similar structures will make it difficult to sync your device. 2. Locate the OBD-II port in your vehicle. The OBD-II port is typically found near the dashboard usually at one of eleven locations in your vehicle as shown in the Figure to the right. In many vehicles the port is located under the steering wheel and above the gas pedal. The OBD-II port has a trapezoidal shape.
PAGE 8
5. Start the vehicle– you should see the LEDs light up on the front of the device. 6. If for any reason you do NOT see the LEDs light up, with the device installed and engine running, unplug the device and repeat steps 3 and 4. 7. Once you see the LEDs flashing – please leave the device plugged in for at least 5 minutes. 8. If your device has a SOLID Cellular light after 5 minutes - the SYNC process is complete. If not, please POWER CYCLE (Instructions below) to restart SYNC process.