Federal Communications Commission (FCC) Statement This Equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
TC-Card Hardware Installation Guide Copyright Notice © 1998 VXL Instruments Limited ALL RIGHTS RESERVED. Document Number : 600010105088 202 2nd Edition, January 1899 Printed in INDIA Information in this document is subject fo change without notice and does not represent a commitment or the part of VXL Instruments Limited.
TC-Card Hardware Installation Guide D Crs Owen FF Kon This Raga is internally et pk, foe I
TC-Card Hardware Installation Guide Contents 0 A INTRODUCTION OVERVIEW. FEATURES . INSTALLATION INSTALLATION PROCEDURE TYPICAL NETWORK INSTALLATIONS PC BIOS SETUP CUSTOMIZING THE CONFIGURATION! TC-CARD SETUP... enn 12 SPECIFICATIONS MECHANICAL. nna 18 ENVIRONMENTAL ELECTRICAL NETWORK CONNECTION...
TC-Card Hardware Installation Guide Chapter-1 INTRODUCTION OVERVIEW Congratulations! You have made the right decision to protect your investment in your existing PC. Easy fo install, TC-Card instantly converts an {BM compatible PC into a Thin Client. After installation you can use your system either in PC mode or as a Thin Client. Following installation into the PC, we will refer to the PC system as a Thin Client while it is connected onto a {CA network.
TC-Card Hardware Installation Guide FEATURES The Thin Client terminal: « is fully compatible with all Windows 3.1, Windows 95, Windows NT and DOS (text) applications through Win Frame and ICA based application servers. « provides secure access to network resources. + provides extremely low administration costs. + is 100% ICA 3 protocol compliant.
“TC-Card Hardware Installation Guide Chapter-2 INSTALLATION The TC-Card carton would contain: . TC-Card « Hardware Installation Guide {which you are currently reading} . . Software User's Guide Note: Trans-shipment should be done in the original packing to avoid damage. Retain the carton and package material for re-packing. INSTALLATION PROCEDURE « Switch oft the PC. Remove the PC's cabinet cover. Precaution : Always switch off the PC before removing or inserting the card.
TC-Card Hardware installation Guide TYPICAL NETWORK INSTALLATIONS The Thin Client communicates with the server using the ICA 3 protocol. This section illustrates how to install Thin Client in different network typologies.
GT-Card Hardware Installation Guide If Direct Connection through RS232 is desired, connect « FS232 cross cable from a PC serial port (COM or Compton a Server serial port as shown in figure below. COM CoM Sever PORT PORT R§232C CROSS Direct Connection through RS232 if Dial-In Remote Connection through modem is desired, connect « RS232 straight cable from a PC serial port to a modem connected to telephone line as shown in figure below.
TC-Card Hardware Installation Guido It your BIOS supports Plug and Play (PnP), enter the PnP PCI CONFIGURATION. The TC-Card is not configured for PnP and # your PC supports this features, it should be disabled for the ISA slat and IRQ selected for this card. Default RQ is 8. PnP PCI CONFIGURATION Resources countrified by Manual IRIS Legacy ISA For other BIOS that support PnP with different setup fields, follow the BIOS instructions to select Ihe TC-Card [RQ as non-PP. » Save and exit from the setup. .
TC-Card Hardware Installation Guide CUSTOMIZING THE CONFIGURATION In most cases the default settings should allow for a simple installation of the TC-Card. With some PCs, particularly those that had been used with many card devices, special setup may be required. The TC-Card is factory set to operate at IRQ § and base's 300th by default and uses ornery space DOOO-D3FF. This setting may be currently used by another card within your PC. There may be two cases to customize your TC-Card.
TC-Card Hardware Installation Guide TC-CARD SETUP TC-Card setup application is used to configure your TC-Card. To enter anti the TC-Card setup application: +» Resettle PC « After fow moments the following message would appear : #TC-Card Configuration# TC-Card is using IRQ 5 and base's 300th Press Ctrl+Alt+z to change settings . + Now press Ctrl+Alt+z simultaneously. « You would enter the TC-Card Setup as shown below.