M4000 Quick Start Manual v1.
CONGRATULATIONS ON YOUR NEW VUZIX M4000 SMART GLASSES SYSTEM Your M4000 Smart Glasses System is an ergonomically designed, wearable Android-based computer with Wi-Fi connectivity, voice-command functionality and HD camera — right out of the box, including: 02 • M4000 see-through viewer with adjustable waveguide display screen • 1000 mAh USB-C power bank • USB-A to USB-C power cable • USB-C to USB-C viewer cable • M-Series Safety Glasses viewer frames with rail mounts • Hard case for storage •
CHARGING FOR FIRST-TIME USE USB-C BATTERY VIEWER USB-C TO USB-C CABLE Charge battery before use with a standard USB wall charger, wait until all three LEDs are solid. Assembling the M4000 mounting system Can take up to two hours if the battery is fully empty.
ASSEMBLING YOUR M4000 SMART GLASSES SYSTEM 1. Before attaching the viewer to either side of the smart glasses frame, determine your dominant eye for optimum use of M4000 capabilities 2. Attach viewer to your preferred side of the safety glasses by sliding the mounting rail onto the temple mount on the frames. Once properly fitted, the unit will be adjustable by sliding forward and backward, and rotating/tilting the the display. 3.
ADJUSTING & CLEANING THE M4000 Holding only the plastic housing of the lens, adjust left, right, up and down for optimal use. NEVER adjust by touching/moving the waveguide display—doing so may damage or destroy the waveguide display. When cleaning, you may stabilize the display by gently holding the outer edge, but only if the rest of the unit is properly supported.
NAVIGATING THE M4000 USB-C Port Mounting Rail Navigation Buttons Center Front Back Power LED Waveguide Display Touchpad Power Button (rotate arm to access) Camera Flash 06 Recording LED
TOUCHPAD BUTTON NAVIGATION Short press for primary functions: front: forward navigation center: back navigation back: select Long press (approx one sec) touch for secondary functions: front: right-click center: exit to home menu back: back one step TOUCHPAD NAVIGATION The 2-axis pad responds to up and down or back-to-front finger swipes. Tap to select.
WEARING THE M4000 WI-FI QUICK CONNECT The easiest way to connect to Wi-Fi is by scanning a QR code. QR code setup: 1. Create a QR code securely* using www.vuzix.com/wifiQR directly from your phone or computer. 2. Open Scanner from the main carousel. 3. Center available QR code in viewfinder to scan. *Vuzix cares about your privacy and security. By visiting this link, our website sends your browser the software to create the QR code.
REGISTERING YOUR DEVICE INSTALLING APPLICATIONS One finger: Applications can be installed on the M4000 via the Vuzix App Store. The Vuzix App Store will install and manage applications via the OTA (Over the Air) mechanism and will require Wi-Fi connectivity. 1. Register your device by logging on to your Vuzix App Store account or registering from a computer or phone at www.vuzix.com/appstore/user/add-device. 2. Follow the instructions on the website 3.
GETTING THE LATEST UPDATES The M4000 will automatically check for updates once it is connected to Wi-Fi. Click Update Now on the following pop-up. Note: If your corporate firewall prevent access to the external website, your system administrator may provide additional settings for your M4000 or may provide a software update offline.
DEVELOPING FOR M4000 Developer documentation is available at vuzix.com/developers. In order to power the unit during development, please note: • The included battery does not support data pass-through. • The viewer should be plugged into the developer’s machine with a USB C-to-C cable for the best experience. • If a USB A-to-C cable must be used, then using a CDP-capable port will provide enough power.
TROUBLESHOOTING COMMON ISSUES 12 SYMPTOM DIAGNOSIS REMEDY M4000 will not turn on and status LED is not lit. Battery is discharged. Connect battery to wall charger for up to two hours for a full charge, then connect battery to viewer. M4000 will not turn on and status LED is blinking red. Internal battery is discharged. Leave viewer connected to USB power. System will begin booting within a few minutes. M4000 display is not on but status LED is lit. Screen has turned off to conserve power.
CLEANING AND CARE • Clean the viewer and battery with a damp cloth and mild detergent if necessary. Do not use all-purpose cleaners as these may damage the seals and impair the water resistance. • Make sure that there is no standing water in the USB connector before inserting the cable. • Do not insert sharp objects into any holes in the viewer as this may damage the mesh and impair the water resistance. • Do not use metal objects to clean the USB port as this may cause electrical damage.
How to Search E-label Step 1: Settings Step 2: About Glasses FCC Caution: This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules.
— Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. The device has been tested and in compliance with SAR limits. This equipment should be installed and operated with minimum distance 0mm between the radiator & your body.
LEARNING MORE Visit www.vuzix.com/support/M4000-smart-glasses to reference a comprehensive online user’s manual or contact technical_support@vuzix.com for additional information and assistance. FOR MORE INFORMATION ON THE M400 AND ACCESSORIES, VISIT: vuzix.com | vuzix.eu | vuzix.jp Vuzix Corporation 25 Hendrix Road West Henrietta, NY 14586 ©Vuzix 2020. This User Manual is subject to change. Please read the included safety information, also at www.vuzix.