User's Manual

Touch and learn!
Touch and learn!
LF1911
High Definition High Definition
Pan & Tilt CameraPan & Tilt Camera
Need help?
Visit leapfrog.com/support
Parent Guide
This guide contains important information.
Please keep it for future reference.
Visit our website leapfrog.com leapfrog.com for more information
about products, downloads, resources and more.
Read our complete warranty policy online at
leapfrog.com/warranty.
Scan the QR
code to enter our
Online Manual:
Or go to leapfrog.zendesk.com/hc
UL STD.
62368-1
CERTIFIED TO
CSA STD.
C22.2 NO.62368-1
CONFORMS TO
Important Safety Instructions
The applied nameplate is located at the bottom of the camera’s base.
When using your equipment, basic safety precautions should always
be followed to reduce the risk of fire, electric shock and injury,
including the following:
1. Follow all warnings and instructions marked on the product.
2. Adult setup is required.
3. CAUTION: Do not install the camera at a height above 2 meters.
4. This product is not a substitute for adult supervision of the infant.
Supervising the infant is the parent’s or caregiver’s responsibility.
This product could cease operating, and therefore you should not
assume it will continue working properly for any given period of
time. Further, this is not a medical device and should not be used
as such. This product is intended to assist you in supervising your
baby.
5. Do not use this product near water. For example, do not use it next
to a bath tub, wash bowl, kitchen sink, laundry tub or swimming
pool, or in a wet basement or shower.
6. Use only the adapters included with this product. Incorrect
adapter polarity or voltage can seriously damage the product.
Power adapter information:
Camera Output: 5V DC 1.5A;
VTech Telecommunications Ltd.; Model: VT07EUS05150
7. The power adapters are intended to be correctly oriented in a
vertical or floor mount position. The prongs are not designed to
hold the plug in place if it is plugged into a ceiling, under-the-
table or cabinet outlet.
8. For pluggable equipment, the socket-outlet shall be installed
near the equipment and shall be easily accessible.
9. Unplug this product from the wall outlet before cleaning.
10. Do not use liquid or aerosol cleaners. Use a damp cloth for
cleaning. Do not cut off the power adapters to replace them with
other plugs, as this causes a hazardous situation.
11. Do not allow anything to rest on the power cords. Do not install
this product where the cords may be walked on or crimped.
12. This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of the
type of power supply in your home, consult your dealer or local
power company.
13. Do not overload wall outlets or use an extension cord.
14. Do not place this product on an unstable table, shelf, stand or
other unstable surfaces.
15. This product should not be placed in any area where proper
ventilation is not provided. Slots and openings in the back or
bottom of this product are provided for ventilation. To protect
them from overheating, these openings must not be blocked by
placing the product on a soft surface such as a bed, sofa or rug.
This product should never be placed near or over a radiator or
heat register.
16. Never push objects of any kind into this product through the
slots because they may touch dangerous voltage points or create
a short circuit. Never spill liquid of any kind on the product.
17. To reduce the risk of electric shock, do not disassemble this
product, but take it to an authorized service facility. Opening or
removing parts of the product other than specified access doors
may expose you to dangerous voltages or other risks. Incorrect
reassembling can cause electric shock when the product is
subsequently used.
18. You should test the sound reception every time you turn on the
units or move one of the components.
19. Periodically examine all components for damage.
20. There is a very low risk of privacy loss when using certain
electronic devices, such as cameras, cordless telephones, etc. To
protect your privacy, make sure the product has never been used
before purchase, reset the camera periodically by powering off
and then powering on the units, and power off the camera if you
will not use it for some time.
21. Children should be supervised to ensure that they do not
play with the product.
22. The product is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
SAVE THESE INSTRUCTIONS
Cautions
1. Use and store the product at a temperature between 32
o
F
(0
o
C) and 104
o
F (40
o
C).
2. Do not expose the product to extreme cold, heat or direct
sunlight. Do not put the product close to a heating source.
3.
Warning—Strangulation Hazard—Children
have STRANGLED in cords. Keep this cord out of
the reach of children (more than 3 ft (0.9m)
away). Do not remove this tag.
4. Never place the camera(s) inside the baby’s crib
or playpen. Never cover the camera(s) with anything such as
a towel or a blanket.
5. Other electronic products may cause interference with your
camera. Try installing your camera as far away from these
electronic devices as possible: wireless routers, radios, cellular
telephones, intercoms, room monitors, televisions, personal
computers, kitchen appliances and cordless telephones.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices):
Wireless Technology Research, LLC (WTR), an independent
research entity, led a multidisciplinary evaluation of the
interference between portable wireless devices and implanted
cardiac pacemakers. Supported by the U.S. Food and Drug
Administration, WTR recommends to physicians that:
Pacemaker patients
• Should keep wireless devices at least six inches from the
pacemaker.
• Should NOT place wireless devices directly over the
pacemaker, such as in a breast pocket, when it is turned ON.
WTR’s evaluation did not identify any risk to bystanders with
pacemakers from other persons using wireless devices.
Electromagnetic fields (EMF)
This LeapFrog product complies with all standards regarding
electromagnetic fields (EMF). If handled properly and according
to the instructions in this user’s manual, the product is safe to be
used based on scientific evidence available today.
1 set for LF1911
1. Connect the Camera
Slide the ON/OFF switch to
to power on your camera.
Note:
• POWER LED Light is OFF by default.
What’s Included
Download LeapFrog Baby Care App
2. Power On or Off the Camera
Connect and Power On the Camera
On LeapFrog Baby Care App
Before you start...
• Connect your mobile device to a 2.4GHz Wi-Fi network for a better connection and smoother video
streaming.
• Enable the Location Service of your mobile device for the purpose of camera setup.
With a Wi-Fi network and enabled Location Service...
You can start to pair the camera with your own mobile device following the instructions in the app. Upon
the successful pairing, you can hear and watch your baby via your mobile device.
Tips:
• Move the camera and the Wi-Fi router closer to each other in order to strengthen the network signal.
• It takes up around 1 minute to search the camera.
Parent Guide
x 2 x 2
App Compatibility
• Android
TM
6.0 or later
• iOS 12 or later.
Start monitoring from anywhere.
Scan the QR code to download the free LeapFrog Baby Care mobile app, or search “LeapFrog Baby Care”
on Apple App Store or Google Play Store.
Strangulation
Hazard
Keep this cord out of reach of children.
The cord needs to be at least three feet
away from the child at all times. Do not
use with an extension cord. Do not
remove this tag.
Éloignez ce cordon des enfants. Le
cordon doit se trouver à au moins trois
pieds d’un enfant et ce, en tout temps.
N’utilisez pas de rallonge. Ne retirez pas
cette étiquette.
Mantenga este cable fuera de la alcance
de los niños. Este cable debe estar por
lo menos tres pies fuera de la alcance
del niño en todo momento. No lo use
con una extensión inalámbrica. No quite
esta etiqueta.
Risque
d’étranglement
Riesgo de
estrangulación
Notes:
• Use only the power adapter supplied with this product.
• If the camera is connected to a switch controlled electric outlet, make sure the switch is on.
• Connect the power adapters in a vertical or floor mount position only. The adapters’ prongs are not designed to hold
the weight of the camera, so do not connect them to any ceiling, under-the-table, or cabinet outlets. Otherwise, the
adapters may not properly connect to the outlets.
• Make sure the camera and the power adapter cords are out of reach of children.
• To maintain compliance with the FCC’s RF exposure guidelines, place the camera at least 20cm from nearby persons.
Pair the Camera with your Mobile Device
After installing the LeapFrog Baby Care App...
• Sign up for an account
• Pair the camera with your mobile device
• Monitor your baby using a wide range of features
Mount the Camera (Optional)
Notes:
• Check for reception strength and the camera viewing angle before drilling the holes.
• The types of screws and anchors you need depend on the composition of the wall. You may need to purchase the
screws and anchors separately to mount your camera.
1. Place the wall mount
bracket on a wall and
then use a pencil to mark
the top and the bottom
holes as shown. Remove
the wall mount bracket
and drill two holes in the
wall (7/32 inch drill bit).
2. If you drill the holes into a stud,
go to step 3.
• If you drill the holes into an
object other than a stud, insert
the wall anchors into the holes.
Tap gently on the ends with a
hammer until the wall anchors
are flush with the wall.
3. Insert the screws
into the holes
and tighten the
screws until
only 1/4 inch of
the screws are
exposed.
4. Place the camera on the wall mount bracket. Insert the
mounting studs into the wall mount holes. Then, slide the
camera forwards until it locks securely. Align the holes on the
wall mount bracket with the screws on the wall, and slide the
wall mount bracket down until it locks into place.
1
2
5. You can maximize your camera viewing angles
by tilting the wall mount bracket.
Hold the camera, and then rotate the knob in
an anti-clockwise direction. This will loosen the
joint of the wall mount bracket.
Tilt your camera up or down to adjust to your
preferred angle. Then, rotate the knob in a
clockwise direction to tighten the joint and
secure the angle.
1
Tip:
• You can find the wall mounting tutorial video and
step-by-step guide by visiting our Online Manual.
> 3ft (1m)
2
Pan and Tilt your camera viewing
up to 110 degrees.
Position the Camera