User's Manual

Status icons
Connection status
• displays when strong signal strength is detected between the baby unit
and the parent unit.
• or displays when moderate or low signal strength is detected between
the baby unit and the parent unit.
• displays when the link between the baby unit and the parent unit is lost.
Lullaby
• Displays when the baby unit being viewed is playing lullaby.
or
or
or
Current view status
• Displays the number of the baby unit that is being viewed when in Single CAM
and Patrol mode.
• Displays the baby unit number of the selected baby unit when in Split mode.
Patrol mode
• Displays when the parent unit is in Patrol mode.
• For VM5251-2 only.
Split mode
• Displays when the parent unit is in Split mode.
• For VM5251-2 only
Night vision
• Displays when the baby unit being viewed has activated the night vision feature.
Zoom
• Displays when the current image on the parent unit has zoomed in.
Temperature alert tone
• Displays when the temperature alert tone is set on.
o
F or
o
C Real-time temperature
• Displays the real-time temperature detected by the baby unit in Fahrenheit (
o
F)
or Celsius (
o
C) (e.g. 57
o
F or 14
o
C).
Mute alert
• Displays when the parent unit speaker volume is set to off.
• Displays when the parent unit is talking to the baby unit.
9-level sound indicator
• (1 to 3 bars) indicates low sound level detected by the baby unit.
• (4 to 6 bars) indicates moderate sound level detected by the baby unit.
• (7 to 9 bars) indicates high sound level detected by the baby unit.
Speaker volume
• Displays the parent unit speaker volume level while adjusting.
Battery status
• animates when the battery is charging.
• displays solid when the battery is fully charged.
• displays when the battery is low and needs charging.
AC power without battery
• Displays when the parent unit is connected to AC power without the battery.
The RBRC® seal on the nickel-metal hydride battery indicates that VTech Communications, Inc. is
voluntarily participating in an industry program to collect and recycle these batteries at the end of their
useful lives, when taken out of service within the United States and Canada.
The RBRC® program provides a convenient alternative to placing used nickel-metal hydride batteries
into the trash or municipal waste, which may be illegal in your area.
VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local retailers
participating in the RBRC® program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY® for
information on Ni-MH battery recycling and disposal bans/restrictions in your area. VTech’s involvement in this program
is part of its commitment to protecting our environment and conserving natural resources.
RBRC® and 1 (800) 8 BATTERY® are registered trademarks of Rechargeable Battery Recycling Corporation.
Mesures de sécurité importantes
La plaque signalétique appliquée est située au bas du socle de l’unité du bébé.
Lorsque vous utilisez votre appareil, vous devriez toujours suivre certaines mesures de précaution de base afin de réduire les risques d’incendie,
d’électrocution et de blessures corporelles, dont ceux qui suivent :
1. Observez toutes les instructions et mises en garde inscrites sur l’appareil.
2. L’installation par un adulte est requise.
3. MISE EN GARDE: N’installez pas l’unité du bébé à une hauteur supérieure à 2 mètres.
4. Ce produit ne remplace pas la surveillance adulte du nourrisson. La supervision du nourrisson est la responsabilité du parent ou de la personne qui
s’occupe de l’enfant. Ce produit pourrait cesser de fonctionner et, par conséquent, vous ne devriez pas présumer qu’il continuera de fonctionner
correctement pendant une période de temps donnée. De plus, il ne s’agit pas d’un instrument médical et ne devrait pas être utilisé comme tel. Ce
produit est destiné à vous aider à superviser votre bébé.
5. N’utilisez pas cet appareil près de l’eau ni de toute autre source d’humidité, par exemple, près d’une baignoire, cuve à lessive, évier de
cuisine, dans un sous-sol humide ni près d’une piscine, dans un soussol humide ou une douche.
6. MISE EN GARDE: Utilisez uniquement les piles fournies. Il existe un risque d’explosion si un autre type de batterie est utilisé pour l’unité
Parents. N’utilisez que le bloc-piles rechargeable inclus ou le bloc-piles de rechange (BT198555/BT298555). N’incinérez pas les piles. Celles-ci
risqueraient d’exploser. Jetez les piles usées selon les renseignements suivant le sceau du RBRC
®
.
7. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation d’un adaptateur dont la polarité ou la tension serait inadéquate risque
d’endommager sérieusement le produit et mettre votre sécurité en péril.
Adaptateur de l’unité du bébé : Sortie : 5V CC 600mA
Adaptateur de l’unité du parent : Sortie : 5V CC 1A
8. Lorsqu’ils sont branchés dans une prise de courant, les adaptateurs secteur ont été conçus pour être orientés correctement, soit à la verticale
ou au plancher. Les broches n’ont pas été conçues pour supporter le poids du bloc d’alimentation et le maintenir en place si celuici est branché
dans une prise au plafond, sous une table ou dans un meuble.
9. Pour les PRODUITS À BRANCHER À UNE PRISE DE COURANT, la prise de courant doit être installée près du produit, afin d’assurer une
accessibilité sécuritaire à la prise de courant.
10. Débranchez ce produit de la prise de courant avant de procéder au nettoyage. N’utilisez pas de nettoyants en aérosols. Utilisez un chiffon
humide pour le nettoyer.
11. Débranchez les cordons d’alimentation avant de remplacer le bloc-piles.
12. Ne coupez pas les cordons d’alimentation pour remplacer les fiches, car ceci peut présenter un danger potentiel.
13. Ne laissez aucun objet reposer ni appuyer sur le cordon d’alimentation. N’installez pas cet appareil dans un endroit où l’on risque d’écraser
le cordon d’alimentation ou de le piétiner.
14. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur l’étiquette. Si vous ne connaissez pas le type d’alimentation que
vous possédez à votre domicile, consultez votre marchand ou votre compagnie locale d’électricité.
15. Ne surchargez pas les prises de courant murales ni les rallonges électriques.
16. Ne placez pas cet appareil sur un chariot, meuble, trépied, support de montage ni table chancelants.
17. Les trous et ouvertures du boîtier, situés à l’arrière de l’appareil ou sous celui-ci, servent à aérer l’appareil. Pour l’empêcher de surchauffer,
ne bloquez sous aucun prétexte ces ouvertures et n’empêchez pas l’aération adéquate de l’appareil en le plaçant sur un lit, divan, tapis ou
toute autre surface similaire. De même, ne le positionnez pas à proximité ni au-dessus d’une source de chaleur ou d’un calorifère. De plus,
ne placez pas l’appareil dans un endroit avant de vous assurer qu’il y ait une bonne circulation d’air.
18. N’enfoncez jamais d’objets à travers les ouvertures de cet appareil, car ils pourraient entrer en contact avec des points de tension dangereux ou
causer des courts-circuits qui peuvent dégénérer en incendies ou en risques d’électrocution. Ne renversez jamais de liquide dans ce produit.
19. Afin de réduire les risques d’électrocution, ne démontez pas cet appareil, mais apportez-le dans un centre de service autorisé. L’ouverture du
boîtier ou le retrait de toutes pièces que contient cet appareil, à l’exception de l’accès autorisé à certaines portes ou ouvertures, risque de vous
exposer à des points de tension dangereux ou d’autres dangers. Un remontage incorrect peut par la suite présenter des risques d’électrocution.
20. Vous devriez tester la réception chaque fois que vous mettez l’appareil en fonction.
21. Examinez les composantes afin de vérifier si celles-ci ne sont pas endommagées.
22. Soyez avisé de la perte de la confidentialité lorsque vous utilisez les ondes publiques. Les conversations peuvent être entendues par
d’autres moniteurs de bébé, des téléphones sans fil, des scanneurs, etc.
23. Les enfants devraient être supervisés afin de vous assurer qu’ils ne jouent pas avec l’appareil.
24. Le produit n’est pas conçu pour être utilisé par des personnes (incluant des enfants) aux capacités physiques, sensorielles ou mentales
réduites ou qui manquent d’expérience et de connaissances, à moins qu’on leur ait donné suffisamment de supervision ou d’instructions
relativement à l’utilisation de l’appareil par une personne responsable de leur sécurité.
CONSERVEZ CES INSTRUCTIONS
Mises en garde
1. Utilisez et entreposez le produit à une température entre 0˚ C (32˚F) et 40˚C (104˚ F).
2. N’exposez pas cet appareil à des froids ou des chaleurs extrêmes, ainsi qu’à la lumière directe du soleil. Ne l’installez pas près d’une source
de chauffage.
3. Le bloc-piles ne doit pas être exposé à la chaleur excessive telle que la lumière du soleil ou au feu.
4. Assurez-vous que le moniteur et le cordon de l’adaptateur sont toujours hors de portée des enfants, àau moins 1 mètre (3 pieds) de l’enfant ou
du berceau, pour éviter tout risque de strangulation.
5. Ne jamais placer le moniteur à l’intérieur du berceau ou du parc de bébé. Ne jamais couvrir le moniteur ou l’unité (s) portative avec un article
tel une serviette ou une couverture.
6. D’autres équipements électroniques peuvent produire des interférences sur votre moniteur vidéo et audio. Tentez d’installer votre moniteur
vidéo ou audio à l’écart des appareils électroniques tels que des routeurs sans fil, radios, téléphones cellulaires, interphones, moniteurs,
téléphones, ordinateurs personnels, électroménagers et téléphones sans fil.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (ne s’applique qu’aux dispositifs numériques sans fil) :
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche indépendante, a mené une évaluation pluridisciplinaire des
interférences entre les téléphones sans fil portatifs et les stimulateurs cardiaques implantés dans l’organisme. Appuyée par l’Administration des
aliments et drogues (FDA) des États-Unis, la firme WTR recommande aux médecins:
Avis aux détenteurs de stimulateurs cardiaques
• Vous devriez maintenir les dispositifs sans fil à au moins six pouces du simulateur cardiaque.
• Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-ci
est en marche.
L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs de simulateurs cardiaques causés par les gens qui utilisent
dispositifs sans fil à proximité de ceux-ci.
Champs électromagnétiques (EMF)
Ce produit de VTech est conforme à toutes les normes se rapportant aux champs électromagnétiques (EMF) standard. Si vous le manipulez
correctement en suivant les instructions de ce guide, son utilisation sera sécuritaire pendant de nombreuses années, selon les meilleures
évidences scientifiques dont nous disposons aujourd’hui.
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the
Product and all accessories provided in the sales package (“Product”) are free from defects in material and workmanship,
pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product
operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United
States of America and Canada.
What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period
(“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will repair or replace at VTech’s option, without
charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement parts. If we
choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will
retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTech’s option, is your exclusive
remedy. VTech will return the repaired or replacement Products to you in working condition. You should expect the repair or
replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces
a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the repaired or
replacement Product for a period of either (a) 90 days from the date the repaired or replacement Product is shipped to you
or (b) the time remaining on the original one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal
operation or handling, neglect, inundation, fire, water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration or modification by anyone other than an authorized service
representative of VTech; or
3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna
systems; or
4. Product to the extent that the problem is caused by use with non-VTech accessories; or
5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed,
altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for
commercial or institutional purposes (including but not limited to Products used for rental purposes); or
7. Product returned without a valid proof of purchase (see item 2 below); or
8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.
How do you get warranty service?
To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call 1 [phone]. In
Canada, go to www.vtechcanada.com or call 1 [phone].
NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and features may save
you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are
responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return
repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech
assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or
proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the
cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of
Products that are not covered by this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the VTech service location along with a
description of the malfunction or difficulty; and
2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and the date of
purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone number.
Other limitations
This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral
communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes
all of VTech’s responsibilities regarding the Product. There are no other express warranties. No one is authorized to make
modifications to this limited warranty and you should not rely on any such modification. State/Provincial Law Rights: This warranty
gives you specific legal rights, and you may also have other rights, which vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty
that the Product is fit for ordinary use) are limited to one year from the date of purchase. Some states/provinces do not
allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech
be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or
revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third
parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.
This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor
is set up to comply with the energy-conserving standards right out of the box. Follow the instructions to install and charge
the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to baby
units, the CEC battery charging testing mode is activated while it is powered off and charging.
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the
Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this equipment not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed
by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with
the FCC criteria. The baby unit shall be installed and used such that parts of all persons’ body are maintained at a distance of
approximately 8 in (20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your
face.
This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B)
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause
interference. (2) This device must accept any interference, including interference that may cause undesired operation of the
device.
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical specifications were
met.
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
RF radiation exposure statement
The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should
be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons’ body. Use of other
accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect
to Canada’s Health Code 6 for Exposure of Humans to RF Fields.
The RBRC® seal For cETL compliance only Limited warranty
California Energy Commission battery
charging testing mode
FCC and IC regulations
Below are the questions most frequently asked about the baby monitor. If you cannot find the answer to your question,
visit our website at www.vtechphones.com, or contact 1 [phone] for customer service.
Why does the
baby monitor
not respond
normally?
Try the following (in the order listed) for common cure:
1. Disconnect the power to the baby units and the parent unit.
2. Remove the batteries in the parent unit. Then, install the batteries again.
3. Wait a few seconds before connecting power back to the baby units and the parent unit.
4. Turn on the baby units and the parent unit.
5. Wait for the parent unit to synchronize with the baby units. Allow up to one minute for
this to take place.
Why don’t the
power-on light of the
baby unit and parent
unit go on when I switch
on the units?
Perhaps the parent unit is not connected to the power. Insert the appliance plug into the
parent unit and put the adapter in a wall socket. Then, press and hold POWER to switch
on the parent unit and to establish connection with the baby unit.
Perhaps the baby unit is not connected to the power. Insert the appliance plug into the
baby unit and put the adapter in a wall socket. Then, slide the ON/OFF switch to ON to
switch on the baby unit and to establish connection with the parent unit.
Why doesn’t my parent
unit charge while
connected to AC power?
Make sure the power is not controlled by a wall switch.
Make sure the battery is correctly installed in your parent unit.
You may have used the battery for a long time. Replace a new battery.
Why is my screen in black
and white?
The screen is in black and white during night-time or in a dark room when the night
vision feature is activated. This is normal.
Why do I get glare or
blurry display on my
screen when viewing my
baby at night?
During night-time or in a dark room, the surroundings and other interfering factors,
like lightings, objects, colors and backgrounds may affect the image quality on your
parent unit screen. Adjust the baby unit’s angle or place the baby unit at a higher level to
prevent glare and blurry display.
Why does the baby
monitor produce a
high-pitched noise?
The parent unit and baby units may be too close to each other.
• Move the parent unit away from the baby units until the noise stops; OR
• Turn down the volume of your parent unit.
Why does the parent unit
beep?
The baby units may be out of range. Move the parent unit closer to the baby units (but
not less than 3 feet).
The parent unit may not have enough charge for the parent unit to perform normally.
Charge the battery in the parent unit for up to 3 hours.
If your parent unit is in Split mode, some of your baby units may detect sounds.
The temperature of your baby’s room may be too high or too low.
Why does the parent unit
beep frequently in Split
mode?
You may have set the VOX sensitivity level to Highest when the sound alert feature is
turned on. The parent unit notifies you of all sounds including background noise with
beeps. Adjust the VOX sensitivity to a lower level.
Why does the parent unit
react too quickly to other
sounds?
The baby unit also picks up other sounds than those of your baby. Adjust the VOX
sensitivity level to a lower level or lower the parent unit speaker volume.
Why don’t I hear a sound/
Why can’t I hear my baby
cry?
The parent unit speaker volume may be too low. Press to increase the volume.
You may have set a low VOX sensitivity level. See Adjust the sound sensitivity of the baby
unit to set to a higher level.
Why can’t I establish a
connection? Why is the
connection lost every now
and then? Why are there
sound interruptions?
The baby units may be out of range. Move the parent unit closer to the baby units (but
not less than 3 feet).
Other electronic and wireless products may cause interference with your baby monitor.
Try installing your baby monitor as far away from these devices as possible.
If you power on only one baby unit, your parent unit may display and No link to CAM #,
and the LINK LED light flashes. Press VIEW to switch to the baby unit you have powered on.
Frequently asked questions
When you are not going to use the baby monitor for some time, remove the rechargeable battery from the
parent unit. Store the parent unit, the baby unit and the adapters in a cool and dry place.
Storage
Parent unit icons
Parent unit overview (Con’t)
1 LED lights
Indicate the different statuses of the
parent unit. For details, refer to Parent
unit lights.
2 LCD display
3
VOL
4
VOL
1 Microphone
2 Camera
3 Light sensor
4 ON/OFF LED light
• On when the baby unit is turned on
and is paired to the parent unit.
• Flashes when the baby unit is not
being viewed;
or when the link to the parent unit is
lost.
5 Infrared LEDs
6 Pair hole
• Your baby units and parent unit
provided are already paired.
7 Speaker
8 Temperature sensor
9
ON/OFF switch
• Slide to turn on or off the baby unit.
10 Power jack
11 Wall mount holes for upright
mounting
12 Wall mount holes for lateral mounting
• While in a menu, press to return to
the main menu or idle screen.
Caution
• Do not install the baby unit at a
height above 2 meters.
Baby unit overview
11
12
Main menu icons
Monitoring Mode
• If you have two baby units, you can select a monitoring mode (Single CAM, Patrol
or Split).
• For VM5251-2 only.
Alert Tone
You can set the parent unit to beep when
• the parent unit operates in low battery condition;
• the link between the parent unit and the baby unit is lost; or
• the baby unit detects sounds while in Split mode.
Language
• You can select a language (English, French or Spanish) to be used in all screen displays.
LCD
• You can change the brightness of the parent unit screen, or turn on the Dim Mode
to save power.
Rename
• You can choose a specific name for the baby unit from a pre-defined name list.
VOX Sensitivity
• With this feature, you can choose to hear sounds from the baby unit all the time, or
to hear sounds that exceed a certain level. You can use the parent unit to adjust the
microphone sensitivity of your baby unit. The higher the sensitivity level, the more
sensitive the baby unit is in detecting sounds for transmitting to the parent unit.
Sound-activated Screen
• When the baby unit detects no sound, the parent unit screen stays off to save
power. Once a sound is detected, the parent unit screen turns on automatically. It
will then turn off again after 50 seconds of no sound detection.
Temperature
• You can choose to set the maximum/ minimum temperature and turn on the
Temperature alert tone, so that the parent unit beeps whenever the room
temperature detected by the baby unit falls outside of the desired temperature range.
• You can choose to display the temperature in Fahrenheit (
o
F) or Celsius (
o
C) on your
parent unit.
Lullaby on CAM
• You can choose a lullaby or soothing sound to comfort your baby.
Volume on CAM
• You can adjust the volume of baby units which determines the lullaby volume and
talkback volume transmitted from parent unit.
Warning icons and messages
No link to CAM #
*
The selected baby unit is out of range or is turned off.
Battery low at
Parent Unit
The battery level of the parent unit is very low and needs to be
recharged.
Battery empty.
Powering off ...
The battery is empty and needs to be recharged.
Sound detected at
CAM #
The sound level exceeds the threshold at CAM # in Split mode.
Temperature
too high at CAM #
or
Temperature
too low at CAM #
The temperature detected by the baby unit is higher/lower than
the desired temperature alert range.
Powering on...
The parent unit is turning on.
The parent unit is searching for baby units.
Auto Timer of lullaby is
reset
The timer that determines the remaining play time for the lullabies
is restarted.
The parent unit has just been connected to AC power.
*
# represents the baby unit number.
Parent unit overview
Parent unit lights
LINK • On when the parent unit is linked to the baby unit.
• Flashes when the link to the baby unit being viewed in Single CAM or Patrol
mode is lost; or when the link to at least one baby unit being viewed in Split
mode is lost.
• On when the parent unit is connected to AC power, or the battery is charging.
• Flashes when the parent unit battery is low and needs charging.
• Off when the parent unit is disconnected from AC power.
It turns on:
• When the parent unit speaker volume is set to off; or
• When the parent unit is talking to the baby unit.
TALK • On when the parent unit is talking to the baby unit.
5
Zoom
• Press to zoom in or out.
6 VIEW / LCD ON/OFF
7 Microphone
8 POWER
9 TALK
• Press and hold to talk to the selected
baby unit.
10
• While in a menu, press to return to
the main menu or idle screen.
• While viewing zoomed image,
press and hold to move the zoomed
image leftward.
• While in Split mode, press to move
the selection box leftward.
11
• While in a menu, press to scroll up.
• While viewing zoomed image,
press and hold to move the zoomed
image upward.
12
• While in a menu, press to choose an
item.
• While viewing zoomed image,
press and hold to move the zoomed
image rightward.
• While in Split mode, press to move
the selection box rightward.
13 MENU/SELECT
• Press to enter the menu.
• While in a menu, press to choose an
item, or save a setting.
14
• While in a menu, press to scroll down.
• While viewing zoomed image,
press and hold to move the zoomed
image downward.
15 Antenna
16 RESET
• Force reboot the parent unit.
17 Stand
18 Speaker
19 Power jack
19
The baby unit has infrared LEDs that allow you to see your baby clearly at night or in a dark
room. When the baby unit being viewed detects low light levels, the infrared LEDs are
switched on automatically. The images from the baby unit are in black and white, and
appears on the screen.
Notes
• It is normal if you see a short white glare on your parent unit screen as the baby unit is adapting to
the dark environment.
• When the infrared LEDs are on, the images are in black and white. This is normal.
Tip
• Depending on the surroundings and other interfering factors, like lightings, objects, colors and
backgrounds, the video quality may vary. Adjust the baby unit’s angle or place the baby unit at a
higher level to prevent glare and blurry display.
Night vision
Your baby monitor comes ready for tabletop use. You can also choose to mount your baby
monitor on the wall. See Mount the baby unit on dry wall (optional) in the Quick Start Guide
for the wall mounting instructions.
Mount the baby unit (optional)
To keep this product working well and looking good, follow these guidelines:
• Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors or
fluorescent lamps).
• DO NOT expose it to direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
• Clean with a soft cloth.
• DO NOT immerse the parent unit and the baby unit in water and do not clean them under the tap.
• DO NOT use cleaning spray or liquid cleaners.
• Make sure the baby unit and parent unit are dry before you connect them to the mains again.
General product care
Parent unit icons (Con’t)
Note
The sound alert feature is only available in Split mode.
Monitor the temperature
Your baby unit monitors the temperature of your baby’s room with its built-in temperature
sensor. If the detected temperature is out of the preset temperature range, the parent unit
will display an alert message.
Set temperature range
You can set the desired room temperature alert range. The minimum temperature can be set
between 52
o
F (11
o
C) and 69
o
F (20
o
C). The maximum temperature can be set between 70
o
F
(21
o
C) and 86
o
F (30
o
C).
1. Press MENU when the parent unit is idle.
2. Press or to choose Temperature, then press SELECT.
3. Press or to choose Minimum or Maximum, then press SELECT.
• If you have two baby units, the system prompts you to choose the desired baby unit or
both baby units, press or to choose ALL CAM or CAM #, then press SELECT.
4. Press or to choose the desired minimum or maximum temperature, then press SELECT
to confirm your selection.
Temperature alert tone
You can turn on the temperature alert tone so that the parent unit will emit an alert tone if the
detected temperature is out of range.
1. Press MENU when the parent unit is idle.
2. Press or to choose Temperature, then press SELECT.
3. Press or to choose Alert tone, then press SELECT.
• If you have two baby units, the system prompts you to choose the desired baby unit or
both baby units, press or to choose ALL CAM or CAM #, then press SELECT.
4. Press or to choose On or Off, then press SELECT to confirm your selection.
Temperature format
You can choose to display the temperature in Fahrenheit (
o
F) or Celsius (
o
C).
1. Press MENU when the parent unit is idle.
2. Press or to choose Temperature, then press SELECT.
3. Press or to choose Format, then press SELECT.
4. Press or to choose
o
F or
o
C, then press SELECT to confirm your selection.
Rename the baby unit
You can rename the baby unit. Once the baby unit is renamed, its new name together with
the baby unit number will appear in the sub-menu of below options:
• VOX Sensitivity • Rename • Temperature
1. Press MENU when the parent unit is idle.
2. Press or to choose Rename, then press SELECT.
3. Press or to choose the desired baby unit, then press SELECT.
4. Press or to choose the desired name for the baby unit, then press SELECT to confirm
your selection.
3
Using the baby monitor (Con’t)