User's Manual

Congratulations
on purchasing your new VTech product.
Before using this product, please read
Important safety instructions.
This manual has instructions on how to set
up and register your new Wall Switch in the
app of your IP Hub. For detailed operations
in the IP Hub app, see the user’s manual that
came with your IP Hub app.
You may also view or download the online
User’s manual of the IP Hub for a full set
of installation and operation instructions at
www.vtechphones.com.
In Canada, visit www.vtechcanada.com.
Introduction
This Wall Switch enables you to control up to
four LED light bulbs that you have registered
to the IP Hub.
Launch the IP Hub app on your iOS or
Android smartphone or tablet, and link the
designated buttons to the respective LED
light bulbs. You can then turn on or off the
respective LED light bulb at once.
What’s in the box
Your product package contains the following
items. Save your sales receipt and original
packaging in the event warranty service is
necessary.
Wall Switch overview
Wall switch unit overview
1 – ON/OFF buttons
Press to turn on or off the LED Light
Bulbs linked to the respective buttons.
2 – Magnet Sensor
3 – Battery Compartment Cover
Magnet plate overview
4 – Magnet Base
5 – Holes for screws
6 – Sticking areas for mounting tapes
•
Before use
Insert the batteries
Slide open the battery compartment
cover.
Insert the batteries into the battery
compartment.
Add and register a new Wall
Switch
Your new VC7011 Wall Switch can be
registered to your account in the app of your
VC71214/VC71215/VC71216/VC71217
IP Hub for use with the VC7004 Multi-Color
Smart LED Light Bulb.
Register the Wall Switch to your account in
the app of your VC71214/VC71215/VC71216/
VC71217 IP Hub before use.
1.
2.
Register a new Wall Switch:
Place the Wall Switch and your
smartphone/tablet close to the IP Hub.
If you have not registered the VC7004
Multi-Color Smart LED Light Bulb to
the IP Hub yet, please refer to the
User’s manual of VC7004 to register
the LED Light Bulb to the IP Hub.
2. Launch the IP Hub app on your
smartphone or tablet and login to your
account.
Create a new account if you do not
have one yet.
3. Press and hold the pair button in the
battery compartment until the LED light
flashes red.
1.
•
•
4. In the app, enter the registration mode
by selecting the option for adding a Wall
Switch to your device list. The registration
process takes about 90 seconds to
complete.
5. Slide the battery compartment cover back
until it securely clicks into place.
6. In the app, link each button of the Wall
Switch to the registered LED Light Hulb.
NOTES
Refer to the user’s manual of your VC71214/
VC71215/VC71216/VC71217 IP Hub for more
detailed instructions.
You can also download online User’s manuals at
www.vtechphones.com/support/manuals.
Replacing a Wall Switch
If you have purchased this new VC7011 Wall
Switch to replace a Wall Switch in the device
list of your account in the IP Hub app, you
must deregister the registered Wall Switch
first, and then register this Wall Switch to your
account in the IP Hub app.
Deregister a Wall Switch from the device
list:
Refer to the user’s manual of your
VC71214/VC71215/VC71216/VC71217 IP
Hub to deregister a Wall Switch from your
account in the IP Hub app.
•
•
•
Test the signal for the Wall Switch
Make sure you have already logged in to your
account in the IP Hub app.
Enable the Wall Switch in the app (see the
user’s manual of your VC71214/VC71215/
VC71216/VC71217 IP Hub).
Press a Wall Switch button that has linked
to LED Light Bulb. The LED Light Bulb will
turn on.
NOTES
If the Wall Switch does not turn on, move the
Wall Switch and the lamp with LED Light Bulb
closer to the IP Hub.
•
•
VC7011
Wall Switch
for use with
VC71214/VC71215/
VC71216/VC71217 IP Hub and
VC7004 Multi-Color
Smart LED Light Bulb
User’s manual
Wall switch unit
Go to www.vtechphones.com
to register your product for
enhanced warranty support and
the latest VTech product news.
User’s manual
User’s manual
a
b
d
c
e
f
g
h
Magnet plate
a
b
d
c
e
f
g
h
a
b
d
c
f
e
a
b
d
c
e
f
g
h
Double-sided
mounting
tape C x2
Screw x 2 Screw
anchor x 2
3
4
1
(Optional)
Insert screw
anchors if
necessary.
Mount with tape
2
c
c
c
c
Mount the sensor
NOTES
This Wall Switch must be mounted vertically on wall. Do not mount the Wall Switch in a horizontal
orientation, or flat on the ceiling.
Make sure the mounting surface is clean. A textured surface or any imperfections to a smooth surface can
keep the mounting tape from making a strong bond.
If you drill the holes into an object other than a stud, insert the screw anchors into the holes and tap gently
on the ends with a hammer until the screw anchors are flush with the wall or ceiling.
TIP
You can choose to mount the Wall Switch with the mounting tape first. Remove the mounting tape and use
screws later if you decide to mount it at that location for long term.
•
•
•
•
Mount with screws
1
2