User’s Manual BRONCO THE RC TRICERATOPS ™ © 2014 VTech Printed in China 91-002928-000 US
Hi Friend, You’re about to embark on a “dino-mite” adventure with me, Bronco the RC Triceratops™! Just so you know, I’ve been specially created just for you and am part of the VTech® Switch & Go Dinos® Turbo crew! Switch & Go Dinos® are a special breed of dinosaurs that transform from vehicle to dino in a few easy steps.
INTRODUCTION Hey, dude! I’m Bronco the RC Triceratops™. Use my remote control to transform me and make me race.
LED Headlights Off/Channel Switch INCLUDED IN THIS PACKAGE • One VTech® SWITCH & GO DINOS® TURBO: Bronco the RC Triceratops™ • One Remote Controller • One user’s manual • One label sheet WARNING: All packing materials, such as tape, plastic sheets, packaging locks and tags are not part of this toy, and should be discarded for your child’s safety.
GETTING STARTED 1. Make sure the unit and remote control are turned OFF. 2. Locate the battery cover on the bottom of the unit and remote control. Use a screwdriver to loosen the screw. 3. First, install 6 new “AA” size (LR6/AM-3) batteries following the diagram inside the battery box in the main unit. Then, install 2 new “AA” size (LR6/AM-3) batteries following the diagram inside the battery box in the remote controller. (The use of new alkaline batteries is recommended for maximum performance.) 4.
• Use new alkaline batteries for maximum performance. • Use only batteries of the same or equivalent type as recommended. • Do not mix different types of batteries: alkaline, standard (carbonzinc) or rechargeable (Ni-Cd, Ni-MH), or new and used batteries. • Do not use damaged batteries. • Insert batteries with the correct polarity. • Do not short-circuit the battery terminals. • Remove exhausted batteries from the toy. • Remove batteries during long periods of non-use.
LABEL INSTRUCTIONS 5 6 3 4 7 1 5 6 3 4 2 8 2 8 2 8 Style 2 7 1 5 6 3 4 Label Instructions Style 1 Style 3 7 1 6
Please choose from one of the three label designs to decorate Bronco the RC Triceratops™. Attach the chosen group of labels to the location on the product that matches the number next to the label. 5 7 6 1 4 2 Label Instructions 8 3 Note: It is possible for the front bumper and side panel to get separated if the unit runs into something with enough force. If this happens, please reconnect the front bumper and side panel as shown below.
PRODUCT FEATURES 1. TURN THE UNIT ON Slide the Remote Control Off/Channel Switch to the I or II position to turn the Remote Control ON. Note: I and II settings are two different channels the Remote Control and Bronco the RC Triceratops™ can operate on. If two units are operating in the same vicinity, put one unit on channel I and the other on channel II. 2. REMOTE CONTROL POWER INDICATOR After the Remote Control is turned ON, the Remote Control Power Indicator will flash to show the remote is ON.
4. TURBO CHARGE LEVER Move the Turbo Charge Lever up and down to charge Bronco the RC Triceratops’ turbo boosters. When Bronco is fully charged, he says, “charge complete.” If Bronco the RC Triceratops™ has been charged to a level in which he has turbo boost power, the Turbo Boost Button with LED will blink. The faster the Turbo Boost Button with LED is blinking, the more time that will be allotted for the turbo boost.
8. Light Button Press the Light Button to see the two headlights illuminate and hear fun sounds and phrases. 9. TALK BUTTON 10.SOUND BUTTON Press the Sound Button to hear cool sound effects. 11.STYLE BUTTON Press the Style Button to change the dino eyes or choose a driver. Product Features Press the Talk Button to hear the dino or driver talk. 12.VOLUME BUTTON Press the Volume Button to adjust the volume. 13.
To preserve battery life, the Bronco the RC Triceratops™ and the Remote Control will automatically power-off after several minutes without input. Note: If Bronco the RC Triceratops™ automatically turns off, turn the unit off and slide the Off/Channel Switch back to the I or II position used prior to turn it back on. CARE & MAINTENANCE 1. Keep the unit clean by wiping it with a slightly damp cloth. 2. Keep the unit out of direct sunlight and away from any direct heat source. 3.
NOTE: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected • Consult the dealer or an experienced radio/TV technician for help Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003. THIS DEVICE COMPLIES WITH INDUSTRY CANADA LICENCEEXEMPT RSS STANDARD(S). OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION OF THE DEVICE. LE PRÉSENT APPAREIL EST CONFORME AUX CNR D’INDUSTRIE CANADA APPLICABLES AUX APPAREILS RADIO EXEMPTS DE LICENCE.