WVSXM70 / WVSXM70CV Digital Wireless Observation Monitor KEY FEATURES: ● Easy installation - fits most applications ● 7.0" monitor comes with suction cup mount and 12 Volt DC plug for easy portability ● technology- no cables or wiring necessary ● No interference ● Signal transmits through and around objects up to 60+ feet away ● Sharp, clear, uninterrupted picture ● Can support up to four wireless cameras (WVSXC150 or WVSXC160) simultaneously (must be WiSight 2.
INSTALLING THE MONITOR 1. Plug power cable into the back of the monitor. 2. Attach the suction cup mount to the rear of the monitor with the supplied bracket. 3. Locate a flatter section of glass on your windshield (that does not block your vision) and apply suction cup (as shown in diagram). Snap the lever on the suction cup mount into the locked position. 4. Connect the power cord to a 12 Volt DC outlet. 5. Align the antenna to its upright position, parallel to the monitor. OPERATION 1.
KEY FUNCTION 1 Power Button 2 Select/Pair Button 4 Up Button 5 Down Button 3 Menu Button 1. POWER BUTTON - Press once to turn on the monitor. - Press again to turn off the monitor. 2. SELECT/PAIR BUTTON - Press the SELECT/PAIR button for less than 1 second to change the AV Source. - Press the SELECT/PAIR button for over 5 seconds to start the pairing mode. 3.
Tint Color Color 15 Tint 15 Mirror OFF Mirror Flip Flip OFF Dimmimg AutoPower AutoPower Dimming OFF Scale Marker Screen Saver Screen Saver Day Scale Marker ON EN-4 OFF
Split Menu Split Menu 2 Split Channel Select 2 Split Channel Select OFF Volume Trigger Delay Trigger Delay L1,R2 Volume OFF EN-5 7
4. UP AND 5. DOWN BUTTON Function for Brightness, Contrast, Color, and Tint Control - Press the “UP” button to increases brightness, contrast, color, or tint level when accessing menus adjust mode instead of when accessed menu adjust mode. - Press the “DOWN” button to decreases brightness, contrast, color, or tint level when accessing menus adjust mode instead of when accessed menu adjust mode.
Function for Scale Marker - Press the “UP” or “DOWN” to change the Scale Marker mode. 1.OFF mode 2. Mode1 3. Mode 2 5 5 3 3 1 1 Scale Marker Scale Marker 1 4. Mode 3 2 5. Mode 4 5 5 3 3 1 1 Scale Marker 3 Scale Marker 4 Function for Split Menu - Press the “UP” or “DOWN” to change the Split mode. 1.OFF mode 2. 2 Split 3. Quad 2 1 Split Menu 4.
Function for 2 Split Channel Select - Press the“UP” button to change the 2 Split Chanel Select Mode to L1/R2,L1/R3,L1/R4, L2/R1,L2/R3,L2/R4,L3/R1,L3/R2,L3/R4,L4/R1,L4/R2,L4/R3 when accessed menu adjust mode. 1 2 Split Channel Select 2 L1,R2 Function for Trigger Delay - Press the“UP” button to change theTrigger Delay time when accessing menus adjust mode instead of when accessed menu adjust mode. Trigger Delay OFF Function for Speaker Volume Control - Press the “UP“ button to increases volume level.
WIRING DEFINITIONS PIN 1 PIN 2 PIN 3 PIN 4 GPIO CABLE (FOR WVSXM70CV) BLACK GND TRIGGER 1 -BLUE TRIGGER 2 -BROWN TRIGGER 3 -GREEN TRIGGER 4 -ORANGE RED +12V POWER CABLE PIN 5 PIN 6 PIN 7 PIN 8 DI INPUT 1 -YELLOW DI INPUT 2 -PURPLE DO OUTPUT 1 -GRAY DO OUTPUT 2 -WHITE EN-9
FCC IMPORTANT NOTE: 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
TROUBLE SHOOTING Monitor will not turn on. Monitor displays "No Signal". Intermittent reception. - Check power cord connection at monitor and 12VDC socket. - Check fuse in cigarette socket adapter. - Check 12VDC power at camera. - Make sure antenna is tight and pointed correctly. - Make sure monitor is set to CH1. - Try manually pairing the system. see pairing Process for instructions. - Make sure antenna is tight and installed vertically.