Installation Guide

ManualsBrandsVOXX Electronics ManualsAudioDual 10.1" Seat-Back Entertainment System

UNIVERSAL INSTALLATION 10”.1 SEATBACK ENTERTAINMENT SYSTEM (Seat Back Mount)

Page 1 of 8

730148A1

Document #730148 Created ACH 12/20/2018

Revised ACH 12/20/18 – A1

Kit Contents:

Item #

Qty.

Component Description

SB10MD1, SB10M1 Monitors

L Connector Cable

T-Junction Cable

IR Headphone

Metal Shaft Bracket, Black

Metal Stent Briquetting, Black

Plastic Stent, Black

Bracket Cover, Black

Screw Cap

Nylon Tie

Screw Pack

SB10UHD Owner’s Manual

Installation Manual

Voxx Registration Card

SB10UHD Owner’s Manual

Hardware Bag Contents:

Item #

Qty.

Component Description

Screw Pack

Flat Washer

Flat Nut

Lock Washer

Screws, Black

Screws, Silver

Additional Items Required for Installation:

Item #

Qty.

Component Description

Recommended Tools:

Safety Tools

Seat/ Floor Covers

Blankets

Installation Tools

10mm Socket/Ratchet

#2 Phillips Screwdriver

NRT-Nylon Removal Tool

Special Tools

Color Applicability/ Trim Level:

Vehicle Trim Color

Accessory

Color

General Applicability:

Universal

Issues

Vehicles with NO guide sleeves

LEGEND:

STOP: Damage to the vehicle may occur. Do not

proceed until process has been complied with.

OPERATOR SAFETY: Use caution to avoid risk of

injury.

CRITICAL PROCESS: Proceed with caution to

ensure a quality installation. These points will be

audited on a completed vehicle installation.

TOOLS & EQUIPMENT: This calls out the specific

tools and equipment required for this process.

REVISION MARK: This mark highlights a change

in installation with respect to previous issue.

INSTRUCTION/ INSTALLATION NOTES:

• After Safety mandated preparatory steps have been

taken, the installation sequence is the suggested method

for completing the accessory installation.

• When prying panels, use masking tape on all surfaces

that a tool may come in contact with to prevent marring.

• After a wire tie is fully fastened, cleanly cut excess wire

tie length with a pair of wire cutters.

• The wiring information is on an “as is” basis without any

representation or warranty. It is the installer’s

responsibility to verify any circuit before interfacing with it

using a digital multi-meter.

• Manufacturer’s service documents can be used for any

vehicle disassembly that may be depicted differently from

what the instruction states.

• Use Wiring Diagram on last page of document to clarify

cable or component names.

Summary of content (8 pages)

PAGE 1
UNIVERSAL INSTALLATION 10”.1 SEATBACK ENTERTAINMENT SYSTEM (Seat Back Mount) Document #730148 Color Applicability/ Trim Level: Component Description SB10MD1, SB10M1 Monitors L Connector Cable T-Junction Cable IR Headphone Metal Shaft Bracket, Black Metal Stent Briquetting, Black Plastic Stent, Black Bracket Cover, Black Screw Cap Nylon Tie Screw Pack SB10UHD Owner’s Manual Installation Manual Voxx Registration Card SB10UHD Owner’s Manual Accessory Color Kit Contents: Item # Qty.
PAGE 2
UNIVERSAL INSTALLATION 10”.1 SEATBACK ENTERTAINMENT SYSTEM (Seat Back Mount) A. Pre-Installation Precaution Figure B1a 1. Use Seat and Floor protectors to avoid damage to surfaces. Disconnecting the battery prior to any ground or harness removal/ tapping to prevent possible vehicle damage is recommended. The battery may be temporarily reconnected and disconnected throughout the installation process to perform various tasks.
PAGE 3
UNIVERSAL INSTALLATION 10”.1 SEATBACK ENTERTAINMENT SYSTEM (Seat Back Mount) C. Seat Harness Routing Figure C1a 1. Insert a NRT carefully between the guide sleeve and seat material creating a gap between. The NRT will then slide down between the foam and the frame. Once down, twist the NRT to create a larger gap. NOTE: In some seats you may Figure C1b have to remove the guide sleeve to properly slide the NRT between the foam and frame. (Figure C1a-c) Figure C1c 2.
PAGE 4
UNIVERSAL INSTALLATION 10”.1 SEATBACK ENTERTAINMENT SYSTEM (Seat Back Mount) 3. Pull harness until approximately 12” of cable Figure C3a remains at the top of the seat. Slide cable along inside edge of guide sleeve. This will keep harness from being exposed under the bracket. (Figure C3a-b) Figure C3b D. Monitor and Bracket assembly Figure D1a 1. Lay Monitor face down on a soft surface. Notice the 3 locating dimples to align bracket. (Figure D1a-b) Figure D1b 2.
PAGE 5
UNIVERSAL INSTALLATION 10”.1 SEATBACK ENTERTAINMENT SYSTEM (Seat Back Mount) Figure D2b 3. Install 6 screws into bracket and monitor Figure D3a securing the assembly. (Figure D3a-c) Figure D3b Figure D3c 4. Once bracket is secure to the monitor, install Figure D4 bracket cover. (Figure D4) © 2018 Voxx Automotive, Inc. All rights reserved.
PAGE 6
UNIVERSAL INSTALLATION 10”.1 SEATBACK ENTERTAINMENT SYSTEM (Seat Back Mount) E. Mounting Monitor/ Bracket Assembly Figure E1 1. Attach L Connector Harness to the rear of the monitor. (Figure E1) 2. To properly secure the harness to the monitor, Figure E2a first attach a wire tie to the eyelet next to the connection. Install harness connector and secure with the wire tie. Cut excess wire tie before installing monitor. Figure E2b (Figure E2a-c) Figure E2c 3.
PAGE 7
UNIVERSAL INSTALLATION 10”.1 SEATBACK ENTERTAINMENT SYSTEM (Seat Back Mount) Figure E3b 4. While holding both brackets together install 5 flat Figure E4a washers and 5 flat nuts. Tighten all nuts to secure bracket underneath the guidepost. (Figure E4a-b) Figure E4b 4. Install Plastic spacer with 5 flat washers and 5 Figure E4 lock nuts. Tighten all nuts to secure spacer over the guidepost. NOTE: spacer may not sit flush due to the different shape and size of the Guidepost heads.
PAGE 8
UNIVERSAL INSTALLATION 10”.1 SEATBACK ENTERTAINMENT SYSTEM (Seat Back Mount) 6. Re-install headrest. NOTE: Some slight Figure E6 modification may be done to the bracket cover to allow headrest to move up and down freely. (Figure E6) 7. Continue routing harnesses following factory harnesses from the lower seat to a central location in the vehicle. Attach to T-Junction harness. F. Power/Ground Location 1.