What’s inside User Guide Welcome! ................................................................ 2 Getting started ...................................................... 3 Tour of the system ............................................... 7 Everyday use.........................................................13 Cameras ............................................................14 Motion/Alerts ..................................................18 Recording ...............................................
Getting Started WELCOME! This baby monitoring system makes it simple to keep your eyes and ears on your little one! This guide takes you through the steps to get started! Step 1: Unpack Wireless camera Parent monitor See our setup videos Go to ProjectNursery.com/ Electronics or scan the QR code here. The accessories: Before you start... Make sure you read the Important Information sheet included in this package.
Step 2: Charge the monitor Find one of the charging cables included in this package. Getting Started GETTING STARTED Step 3: Position the camera(s) Find a location for the camera that gives you the best view of your baby in his or her crib. Plug one end of this cable into the USB CHARGING jack on the side of the parent monitor. Plug the other end of the charging cable into one of the included charging adapters. Then plug the adapter into an outlet or surge protector.
Getting Started Step 4: Plug in the camera(s) Find the other charging cable(s) included in this package. Step 5: Turn on the monitor Press and hold the POWER button on the parent monitor to turn it on. Plug one end into the CHARGING jack on the back of the camera(s). Congratulations! Your system is ready to use! The camera(s) comes pre-paired with your parent monitor. However, it’s a good idea to go ahead and set the time on your parent monitor now, before you start using it.
Getting Started Step 6: Set the time on the monitor 1 Press the MENU button on the parent monitor. The menu appears on screen. 4 Use the up/down arrow buttons to set the hours, minutes, and AM/PM. Press OK/ ZOOM when you’re finished. 12:00AM 72º Temperature Time Set Time: 12:00 AM Factory Reset Support Product Information 2 Use the arrows to highlight SETTINGS. Press OK/ZOOM to select it. The Settings menu appears on screen. 12:00AM 72º 3 Press the down arrow to highlight Time Set.
TOUR OF THE SYSTEM Parent Monitor accesses the system’s menu screens. Tour of the system turns the monitor on and off (press and hold). and turn the volume down/up. In menu screens, these navigate left/right. zooms the camera in/out. and navigate up/down in menu screens. SOUND LEVEL indicators show you the level of sound from your baby’s room. Watching baby You can turn the display on and off without turning the monitor off.
Parent monitor side and back panels USB CHARGING jack plugs into your charging cable to recharge or power the parent monitor. Tour of the system Built-in easel stand lets you stand the unit on a flat surface. Built-in easel stand Zoom Talking to baby Listening to baby To zoom the active camera: Press the OK/ZOOM button on the parent monitor. To talk through the speaker on the active camera: Press and hold the TALK button on the parent monitor.
Status Bar Indicators Parent monitor Tour of the system 72º Temperature reading shows the strength of the current camera’s signal. 2:35 PM Temperature reading shows the temperature in Fahrenheit at the active camera. If you want to change this to Celsius, see page 27 for instructions. shows the camera that the monitor is currently displaying. indicates that the Low Battery Noise alert is on. This means the monitor gives an audio signal when it needs to be recharged.
indicates the Lullabies are playing through one of the cameras. See page 24 for instructions on playing lullabies. indicate that the monitor is scanning through the available cameras. The number indicates how quickly the monitor switches cameras. See page 17 for information on turning camera scanning on and off. indicates the level of the monitor’s rechargeable battery. If you see it’s time to recharge. See page 3 for more information.
Camera (front, back, and side) Microphone Nighttime sensor Tour of the system Thermal sensor Mounting keyholes POWER (back) turns the camera on and off (press and hold). PAIR (back) links the camera securely with the monitor (press and hold). CHARGING (back) plugs into your charging cable to recharge or power the camera. Mounting keyholes (bottom) let you mount the camera on a wall (mounting hardware not included). Thermal sensor detects the temperature around the camera.
3. EVERYDAY USE 12:00AM 72º Parent Monitor Menu Everyday use This system’s menus let you set up more cameras, set motion and temperature alerts, and much more. This section takes you through each menu. GETTING AROUND IN THE MENUS Press MENU to access the menus. Use the arrows to highlight items. Press OK/ZOOM to select.
Cameras The Cameras menu lets you pair additional cameras or remove them from your list of cameras. If you have multiple cameras, this menu also lets you scan through them one by one. ACCESSING THE CAMERAS MENU Parent Monitor Front 1 Press MENU on the parent monitor. 2 Use the arrow buttons to highlight the Cameras icon, and press OK/ZOOM to select it.
72º 12:00AM View Camera Scan Cameras Pair: Pair: Pair: Pair: Camera Camera Camera Camera 1 2 3 4 5 If the monitor screen shows a green checkmark next to Pair: Camera, you’re all set to use the monitor and the camera! (If it shows a red X, put the camera closer to the monitor and try again.) To view a different camera: 12:00AM 72º Scan Cameras Pair Camera Delete Camera Use the up/down arrows to select Pair: Camera 2, Pair: Camera 3, or Pair: Camera 4. Press OK/ZOOM to select it.
72º 12:00AM View Camera Scan Cameras Pair Camera Delete Camera Scan: Off Scan: 5 Secs Scan: 10 Secs Scan: 15 Secs To scan through the cameras automatically: 1 In the Cameras menu, highlight Scan Cameras. Press OK/ ZOOM to select it. 2 Use the up/down arrows to select how quickly you want to switch cameras: every 5, 10, or 15 seconds. Press OK/ ZOOM to select that option. The screen switches to the first camera, and the status bar at the top of the screen shows an , , or .
Motion/Alerts The Motion/Alerts menu lets you set up alerts that are activated by motion, sound, or temperature in your baby’s room. It also lets you set up an alert for when the monitor’s rechargeable battery needs to be recharged. Parent Monitor Front ACCESSING THE MOTION/ALERTS MENU Press MENU on the parent monitor. 2 Use the arrow buttons highlight the Motion/Alerts icon, and press OK/ZOOM to select it.
12:00AM 72º Motion Activated Video Sound Activated Video: OFF Temperature Alert: OFF Low Battery Noise Alert: OFF Out of Range Alert: OFF 2 OFF ON: LOW ON: Medium ON: High Use the up/down arrows to select the amount of sensitivity you want for the motion sensor: ON: Low, ON: Medium, or ON: High. The status bar at the top of the screen shows an indicator for motion activation: .
12:00AM 72º Motion Activated Video: OFF Sound Activated Video: ON Temperature Alert Low Battery Noise Alert: OFF Out of Range Alert: OFF High Temp: ON: 81 OFF Low Temp: ON: 63 OFF SETTING TEMPERATURE ALERTS These alerts tell you when your baby’s room is too hot or too cold. 1 In the Motion/Alerts menu, select Temperature Alert. 2 Activate the temperature alert you want to use, then set it. The status bar at the top of the screen will show an indicator for temperature alerts: .
72º 12:00AM Motion Activated Video: OFF Sound Activated Video: OFF Temperature Alert: OFF Low Battery Noise Alert: ON Out of Range Alert OFF ON SETTING AN OUT-OF-RANGE ALERT This alert tells you when the monitor is out of range of the camera. 1 In the Motion/Alerts menu, highlight Out of Range Alert and press OK/ZOOM to select it. 2 Use the up/down arrows to turn the out-of-range alert on or off. The status bar at the top of the screen shows an indicator for the out-of-range alert: .
Sleep Mode You can set up your monitor to turn off the display automatically after a set amount of time. Parent Monitor Front ACCESSING THE SLEEP MODE MENU 1 Use the arrow buttons to highlight the Sleep Mode icon, and press OK/ZOOM to select it. Everyday use 2 Press MENU on the parent monitor. 72º 12:00AM Sleep Mode (video off, sound on) OFF ON: 5 mins ON: 30 mins ON: 60 mins SETTING SLEEP MODE 1 In the Sleep Mode menu, press OK/ZOOM to turn sleep mode on.
Lullabies This Project Nursery system comes with 3 lullabies, a nature sound, and white noise ready to play—simply choose the one you want, and the camera you’re on will play it back. PLAYING LULLABIES OR WHITE NOISE Parent Monitor Front 1 Make sure the monitor is displaying the camera you want to play the lullaby on. If you want to play on a different camera, press the MENU button and select CAMERAS. Then press OK/ZOOM to select View Camera and choose the camera you want.
Display You can adjust the brightness of the display, and set it to automatically dim after a set amount of time. ADJUSTING BRIGHTNESS 1 2 3 4 Press MENU on the parent monitor. Use the arrow buttons to highlight the Display icon, and press OK/ZOOM to select it. In the Display menu, highlight Adjust Brightness, and press OK/ZOOM to select it. Use the up and down arrows to adjust the brightness. Press OK/ZOOM when you’ve finished.
Settings The Settings menu lets you customize the monitor to match your preferences. It also gives you technical information about the monitor and support. ACCESSING THE SETTINGS MENU Parent Monitor Front 1 2 Press MENU on the parent monitor. Use the arrow buttons to highlight the Settings icon, and press OK/ZOOM to select it.
12:00AM 72º Temperature Time Set Time: 12:00 AM Factory Reset Support Product Information SETTING THE TIME 1 In the Settings menu, press the down arrow to highlight Time Set. Press OK/ZOOM to select it. 2 Use the up/down arrows to set the time. Press OK/ZOOM when you’re finished.
4. TROUBLESHOOTING / FAQS Most issues with the Project Nursery baby monitoring system can be solved by following one of the troubleshooting tips below. For additional assistance, please call 1-844-393-7338. I don’t see video from the camera on my monitor. + Make sure your monitor is turned on (press the Power button). If it is, press the VIDEO ON/ OFF button to make sure the monitor’s display is awake. Make sure the camera is plugged in to a working outlet and turned on. I see the icon on the screen.
The temperature alerts don’t work. + Make sure you’ve set the temperature preference to the system you use, Fahrenheit (standard in the US) or Celsius (standard outside the US). To switch your temperature preference, go to Settings > Temperature. + Make sure you’ve set the right kind of temperature alert—for example, if you want to make sure your baby’s room does not get below 68 degrees Fahrenheit, set the Low Temp Temperature Alert to 68.
©2017 Voxx Accessories Corp.. 3502 Woodview Trace, Suite 220.
IMPORTANT INFORMATION for Project Nursery PNM4N11 CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN. Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. WARNING: Strangulation Hazard: Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3ft (1m) away). Never use extension cords with AC Adapters. Only use the AC Adapters provided.
FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.