BTunes for V-moda crossfade LP User’s manual
Content ■ Before use…………………………………………………...…1 1. Overview ....................…………………………………...…….1 2. Charging the BTunes…………………………………………….2 ■ Getting started…………………….……………………………2 1. Powering on/off the BTunes............................................................2 2. Installation..................... ..............................................................3 3. Pairing /Connecting....................................................................3 1)Pairing the BTunes with Bluetooth cellphone....
Thank you for choosing the BTunes for V-moda crossfade LP. Please read this user’s manual carefully before use. ■ Before use BTunes for V-moda crossfade LP supports streaming CD quality music from your smart devices, and make phone calls too. 1. Overview 1 3.
2. Charging the BTunes When the BTunes need to be charged, it will emits “Battery low” and the red LEDflashes instead of blue LED. Pleaserecharge the battery of the BTunes. 1) Plug the USB charging cable into the charging jack of a PC or a charger. 2) Plug the end of USB charging cable into the USB port on the BTunes. RED light on→Charging RED light off→Finished charging 3)It will take about 1.5 hours to finish charging. Warning: The battery is recyclable.
Remarks: ◆ The headset will prompt“Battery high”,“Battery medium”, “Battery low” according to the status of battery. ◆ The BTunes will power off automatically to save power if not connected with devices within limited time. 2. Installation. 1) Plug the BTunes into V-moda crossfade LP on the left side. 2) Wear the headset according to L/R side. 3.
Remarks: ◆ Pairing mode will last for 2 minutes, if not paired/connected with devices, the BTunes will into standby mode. ◆ After successful pairing, the BTunes and devices will remember each other, they will not need to re-pair next time. When the BTunes is powered on, it will connect to the last connected devices automatically. ◆ Short press MFB button once when the BTunes not connected with device, it will connect to the last connected device.
3)Pairing the BTunes with multi-point devices The BTunes can connect with two Bluetooth devices at the same time. The general pairing procedures are as follows: 1)Pairing the BTunes with device one. 2) Turn on the BTunes and make it enter into pairing mode again, and pair with device two. 3) Operate device one to connect with the BTunes. The BTunes has already connected with two devices in this moment.
5.
Volume down During a call Press volume down button No prompt tone Transfer conversation to cellphone During a call Press MFB about 2 seconds Transfer audio Transfer conversation to headset During a call Press MFB about 2 seconds Transfer audio Microphone mute During a call Double click MFB button Mute on Cancel mute During a call (microphone mute) Double click MFB button Mute off Active voice Assistant Redial last number Connected mode or playing music Connected mode or playing music D
Note: ◆ Whenpressing the answer button on some cell phone, the call will be transferred to the cell phone. You can switch the call to the BTunes through transfer conversation or operating on the smart devices. Please refer to your smart devices user manual for further information. ◆ Double click MFB button and voice control after you hear “dongdong” after 3 seconds. 6.
Notes: ◆ When the BTunes is connected with two Bluetooth devices, the BTunes can only play music from one device and need pause current music and play music from the other device. ◆ If you want to remote control last/next song, pause/play, it needs your Bluetooth smart devices or Bluetooth transmitter paired with the headset to support AVRCP profile, please refer to the user’s manual of your smart devices or Bluetooth transmitter for further information. 7.
8. Factory Reset In the status of power off or charging, long press MFB button and button about 3 seconds and release it until the red and blue LED flashes simultaneously. Remarks: After factory reset, the paired list of the BTunes will be deleted. After power on again, the BTunes will enter pairing mode automatically, and you need to re-pair and connect with Bluetooth devices. ■ Care and maintenance Read the following recommendations carefully before using the BTunes.
■ FAQs 1.Why is the red LED flashes instead of blue LED? Battery is low, it’s time to charge the battery. 2.Why is the red LED off when charging? a) Please make sure the charging device connect with the BTunes correctly; b) The battery may be drained fully. Please charge the battery for 30 minutes, and then the red LED will be ON. 3.
■ Specifications Bluetooth version Bluetooth V5.0 Bluetooth profiles HFP,HSP, A2DP and AVRCP Operating distance 10 meters Music time Up to 10 hours (moderate volume) Standby time About 360 hours Charging time About 1.5 hours Charging input DC 5.0V /500mA Weight About 13.3 g Measure 78*44.
FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.