E 1 E 1
IMPORTANT SAFETY INSTRUCTIONS • • • • • • • • • • • • • • • • • 2 Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Mains powered apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
THE FCC REGULATION WARNING (for USA) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Introduction Welcome aboard! Thanks for choosing the VOX DA10/DA20. To ensure a long and trouble-free relationship with your new amp, please read this manual carefully, use the amp as directed and keep the manual for future reference. Main features • • • • • 4 The compact DA10/DA20 features ten or twenty watts (10W/20W) producing stellar tones inherited from the VOX Valvetronix series (AD15VT, AD30VT, AD50VT, AD100VT). The amplifier can be powered by six C alkaline batteries.
Setup Installing Batteries Please refer to the illustrations in the section entitled “The Guitarist’s Guided Panel Tour” (page 7). 1. Turn the MASTER volume on the amp all the way down. 2. Insert the batteries as shown on page 5. Alternatively, plug the supplied power cord into the power input on the rear panel, then plug the power cord into a wall outlet. Remove the battery compartment cover located on the bottom of the unit by pulling the ribbon. Insert six C alkaline batteries as shown in the figure.
Replacing the batteries Replace the batteries when the indicator above the STANDBY switch becomes dim. NOTE: If the battery power is low, noise may be heard. NOTE: Depleted batteries must be removed from the DA10/ DA20 immediately. If you leave them in, malfunctions such as battery leakage may occur. You should also remove the batteries if you will not be using the DA10/ DA20 for an extended time.
The Guitarist’s Guided Panel Tour GAIN In this chapter we’re going to take a look at the top and rear panels of your amp. TONE This adjusts the preamp gain. This adjusts the tone. MASTER A. Top Panel This adjusts the overall volume of the amplifier. NOTE: The GAIN control also affects the amount of distortion. For some settings, there may be virtually no distortion. 1 2 3 4 1. INPUT Section This is where you plug in your guitar. 2.
Turn EDIT 1 while pressing BYPASS (EDIT 3) If the BYPASS LED is lit (the effect is bypassed), you can hold down the TAP button and turn the EDIT 1 knob simultaneously to adjust the noise reduction sensitivity. NOTE: You can’t adjust the effect parameters while the BYPASS LED is lit. NOTE: When you turn on the DA10/DA20, the EDIT 2, EDIT 3 and Noise Reduction parameters will be automatically set to the values appropriate to the current selection of the EFFECTS and STYLE selector switches.
B. Rear Panel Vox Amplification Ltd. BUILT BY VOX MANUFACTURING VIETNAM UNDER THE DIRECTION OF VOX R&D ENGLAND. 3021177 WARNING: CONFORMS TO UL STD 60065 CERTIFIED TO CAN/CSA STD C22.2 No. 60065 ATTENTION: DEBRANCHERAVANT DE REMPLACER LE FUSIBLE . TO REDUCETHE RISK OF FIRE OR ELECTRICSHOCK E DO NOT EXPOSE THIS PRODUCTTO RAIN OR M OISTURE . UTILISERUN FUSIBLE DE RECHAN GE DE MEMTYPE. CAUTION: DISCONNECT SUPP LY CORD BEFORE CHANGING FUSE .
Creating Your Own Program and Adjusting the Noise Reduction This section explains how to create your own program, including how to adjust effect parameters and the noise reduction setting. As you’ll hear, selecting a different effect type by using the EFFECTS selector switch will automatically adjust the EDIT 2 and EDIT 3 parameter values to suit the selected effect type.
DELAY TIME: DELAY LEVEL: DELAY FEEDBACK: Press the TAP button twice at the desired interval, or hold down the TAP button and turn EDIT 1. Turn EDIT 1 (without pressing any button). Turn EDIT 1 while holding down the BYPASS button. NOTE: When you select a different type of sound, the noise reduction setting is automatically configured to its initial value to accommodate the selected amp sound Style. 3.
Styles and effects In this section we’re going to talk about the eleven styles and effects. STYLES You know that there is a plethora of great sounding amps out there, and that the quest for the ultimate sound can be endless. After countless hours of soul searching, earnest discussions (not to mention the occasional friendly argument!), calls to tone-wise friends (some professional players, some not ...
CRUNCH 1 This organic sounding style is dynamically rich and warm, yet biting and distinct! Rolling back your guitar’s volume results in a unique and highly usable clean sound. CRUNCH 2 This style has a fat, roaring sound with a distinctive, cranium-crushing crunch. Rolling back your guitar’s volume produces a bright, clean sound that’s perfect for chord work and will cut through any mix.
Effects The DA10/DA20 provides eleven of the most popular effects (some effects actually combine two effects). You can adjust the SPEED parameter of modulation effects or the TIME parameter of delay/reverb effects simply by pressing the TAP switch twice. In addition to using the EDIT 1 knob to adjust the most important parameters, you can make more detailed adjustments by holding down the TAP button or BYPASS button while turning the EDIT 1 knob.
AUTO WAH PHASER This models an auto-wah; a device that creates an automatic “wah” effect that varies with your picking dynamics (i.e., how hard or soft you hit the strings). EDIT 1 “SENS” EDIT 2 “ATTACK” EDIT 3 “POLARITY” Adjusts the sensitivity of the effect in response to the volume of your guitar. Adjusts the response speed of the auto wah. Adjusts the direction in which the effect operates. COMP EDIT 2 “ATTACK” TAP Sets the modulation speed in a range of 0.1...10 [Hz].
TREMOLO TAP This effect is based on the highly acclaimed tremolo circuit found in some guitar amps. TAP “SPEED” EDIT 2 “SPEED” EDIT 3 “DEPTH” Sets the tremolo speed in a range of 2.5...10 [Hz]. This lets you use the knob to make fine adjustments to the parameter. Adjusts the tremolo depth. ROTARY This models a rotary speaker. TAP “SPEED” EDIT 2 “SPEED” EDIT 3 “SENS” Sets the rotational speed of the speaker in a range of 0.8...10 [Hz].
Troubleshooting 1. The amp isn’t powering up when the STANDBY switch is ON. • Have you installed batteries? Is the polarity correct? Or, is the power cord connected to the rear panel of the amp correctly? Is the power cord plugged into an AC outlet? Is the AC outlet switched on and working? Is the power cord damaged? 4. There’s no sound heard from the LINE/PHONE jack when you use it. • • Check that the top panel MASTER volume isn’t turned all the way down. Make sure sound is coming from the amp. 2.
Specifications Number of amp types: Number of effects: Noise reduction: Input/output jacks: Top panel: Rear panel: Power amp output: DA10: DA20: Speaker: DA10: DA20: Signal processing: A/D conversion: D/A conversion: Sampling frequency: Power supply: Power consumption: DA10: DA20: 18 11 11 1 1x INPUT 1x AUX IN jack, 1x MIC INPUT jack, 1x LINE/ PHONE jack Maximum 10W RMS @ 8 ohms Maximum 20W RMS @ 8 ohms 2x VOX original (6.5inch 8 ohm) 2x VOX original (8inch 8 ohm) 24-bit 24-bit 44.
Programmer’s Cheat Sheet Wanna remember how you set up your favorite programs? Well, this is the place to do it! Simply copy the sheet below and mark up by drawing lines or coloring.
IMPORTANT NOTICE TO CONSUMERS This product has been manufactured according to strict specifications and voltage requirements that are applicable in the country in which it is intended that this product should be used. If you have purchased this product via the internet, through mail order, and/or via a telephone sale, you must verify that this product is intended to be used in the country in which you reside.