VOKKERO ELITE FCC | WIRELESS INTERFACE User Guide Version 1.0 XX VOKKERO VOKKERO VOGO NA (North America) 25 Main Street, 3rd Floor Tuckahoe, NY 10707 www.vokkerousa.com VOGO 101, place Pierre Duhem, Immeuble Les Centuries II, 34000 Montpellier, France www.vokkero.
Wireless Interface (WI) ELITE FCC User Guide V1.0 PRÉAMBULE / PREAMBLE • Ce guide décrit les fonctionnalités des produits VOKKERO ELITE FCC, Wireless Interface (WI) ELITE FCC, ses options et ses accessoires. • This guide describes the functionality of the VOKKERO ELITE FCC, Wireless Interface (WI) ELITE FCC products, options and accessories. • Aucun extrait de ce document ne pourra être reproduit ou transmis (sous format électronique ou papier, ou par photocopie) sans l’accord de VOGO.
Wireless Interface (WI) ELITE FCC User Guide V1.0 Table des matières PRÉAMBULE / PREAMBLE 2 INFORMATIONS 4 DISCLAIMER 4 TECHNICAL SUPPORT 4 COMPLIANCE TO FCC US/CAN 5 ENVIRONMENTAL RECOMMENDATIONS 7 WARNINGS 7 USAGE OBLIGATIONS 8 DISPOSAL OF WASTE BY USERS IN PRIVATE HOUSEHOLDS 8 INTRODUCTION 9 AVAILABLE CHANNELS AND USE RESTRICTIONS 9 1. SYSTEM DESCRIPTION 10 1.1. VOKKERO® ELITE WI interface 10 1.1.1. Device interface description 10 1.1.2. General features 10 2. STARTING THE INTERFACE 11 2.1.
Wireless Interface (WI) ELITE FCC User Guide V1.0 INFORMATIONS Document Information Title VOKKERO ELITE FCC Subtitle Wireless Interface (WI) ELITE FCC Document type User Guide Version Version 1.0 This document applies to the following products: GB Nom Référence Wireless Interface (WI) ELITE FCC Up to: VO8161CA DISCLAIMER This document and the use of any information contained therein, is subject to the acceptance of the VOKKERO terms and conditions. They can be downloaded from www.vokkerousa.
Wireless Interface (WI) ELITE FCC User Guide V1.0 COMPLIANCE TO FCC US/CAN • This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause Harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Wireless Interface (WI) ELITE FCC User Guide V1.0 L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Wireless Interface (WI) ELITE FCC User Guide V1.0 ENVIRONMENTAL RECOMMENDATIONS All superfluous packaging materials have been eliminated. We have done everything possible to make it easy to separate the packaging into three types of materials: cardboard (box), expanded polystyrene (filler material) and polyethylene (packets, foam protective sheets). Your device is composed of materials that can be recycled and reused if it is dismantled by a specialist company.
Wireless Interface (WI) ELITE FCC User Guide V1.0 USAGE OBLIGATIONS • • • • • • • GB Before using the system, check that the power supply voltage shown in the user manual corresponds to your supply. If it doesn’t, please consult your supplier. Place the device against a flat, firm and stable surface. The device must be installed in a location that is sufficiently ventilated so that there is no risk of internal heating and it must not be covered with objects such as newspapers, cloths, curtains, etc.
Wireless Interface (WI) ELITE FCC User Guide V1.0 INTRODUCTION The instructions given below will make it simple and easy for you to start using your VOKKERO® ELITE Wireless Interface (WI) communication system. All of the operations described are shared by the versions of the VOKKERO® ELITE WI product listed below: VO8161CA Note: the reference number for your device can be found on the label located on the base of the device.
Wireless Interface (WI) ELITE FCC User Guide V1.0 1. SYSTEM DESCRIPTION 1.1. VOKKERO® ELITE WI interface 1.1.1.
Wireless Interface (WI) ELITE FCC User Guide V1.0 2. STARTING THE INTERFACE Before connecting the power supply, please ensure that the switch on the device is set to OFF • To switch the device on, set the “On/Off” switch to ON. • To switch the device off, set the “On/Off” switch to OFF. 2.1. Description of screen icons (default) Once you have switched on the device, the LCD screen will light up and the VOKKERO® logo will be displayed.
Wireless Interface (WI) ELITE FCC User Guide V1.0 2.3.3. SETTINGS BUTTON The settings button is a continuous rotation button with a validation function. A long press on the button will let you switch to audio configuration mode for input/output. Rotating the button will allow you to navigate between the different available options. Pressing the button will allow you to validate.
Wireless Interface (WI) ELITE FCC User Guide V1.0 3. RADIO CONFIGURATION 3.1. Connection The interface can be connected to the configurator using the USB socket on the top of the device. It must be linked to the USB socket of the VOKKERO® ELITE configurator/charger. The USB cable comes supplied with your ap-pliance. The WI icon will be displayed on the configurator’s home screen. GB USB socket (Type A Female) USB socket (Type B Female) USB cable 3.2.
Wireless Interface (WI) ELITE FCC User Guide V1.0 4. AUDIO CONFIGURATION with 4-wire Intercom systems 4.1. Clearcom 4-wire interface The WI interface is designed to be connected to a 4-wire intercom. Below you will find 2 configuration examples: • Connect a cable between the green connector of the clearcom interface and two XLR 3 pts male and female. In order to identify the cabling, refer to the Clearcom IF4W4 user guide.
Wireless Interface (WI) ELITE FCC User Guide V1.0 4.2. GreenGo 4-wire interface • Connect an XLR 3 pts cable (male/female) between the “OUT1” connector of the 4-wire interface system and the “IN” connector of the Vokkero ELITE wireless interface. • Connect an XLR 3 pts cable (male/female) between the “IN1” connector of the 4-wire interface system and the “OUT” connector of the Vokkero ELITE wireless interface. • Connect the Vokkero ELITE wireless Interface power cable to another power supply.