User's Manual

ManualsBrandsVOCOlinc ManualsElectronicsSmart Contact Sensor

VOCOlinc

VS1

Smart Contact Sensor

Product Overview:

The VOCOlinc Smart Contact Sensor (VS1) lets you know the status of your doors,

windows, cabinets or safety gates, by simply asking Siri or checking your iOS devices,

wherever you are*, via HomeKit, Apple’s smart home platform. You are able to

receive a notification whenever there is any change in the status of your doors or

windows, when equipped with the VS1. You can also use the VS1 to trigger scenes for

home automations (e.g. open window > turn on humidifier). The VS1 uses Bluetooth

low energy technology (BLE) and a replaceable battery (CR2032), which gives you up

to 6 months of battery life. Setup is quick and easy. Make your house safer today.

* an Apple TV (4th gen or above), HomePod or suitable iPad is required as a Home

Hub for remote access. VS1 is exclusively compatible with Apple HomeKit.

Status LED

Indicates accessory status

Summary of content (9 pages)

PAGE 1
VOCOlinc VS1 Smart Contact Sensor Product Overview: The VOCOlinc Smart Contact Sensor (VS1) lets you know the status of your doors, windows, cabinets or safety gates, by simply asking Siri or checking your iOS devices, wherever you are*, via HomeKit, Apple’s smart home platform. You are able to receive a notification whenever there is any change in the status of your doors or windows, when equipped with the VS1. You can also use the VS1 to trigger scenes for home automations (e.g.
PAGE 2
Reset Button Press & hold for about 5 seconds: factory reset All connection data will be cleared. You must remove the accessory from the app and add it back.
PAGE 3
M Adhesive ×2 Key Features: Bluetooth low energy technology 5.0 Real-time status notifications Automate your home by triggering scenes Status LED Up to 6-month battery life (replaceable battery） Compact design Specification Battery: CR2032, DC 3V 220mAh Operation Temperature：0-40℃ Purpose of control：Electrical control Type of action: Type 1.C Control Pollution Degree: PD 2 Number of operation cycles: 10,000 Communication Protocol: Bluetooth 5.0 Signal System: BLE 1M/BLE 2M Operating frequency:2402~2483.
PAGE 4
Quick Start Guide Installation 1. Open the battery cover located on the back of the contact sensor with the aid of tools and insert the button battery (CR2032) into the contact sensor. Starting the pairing process (please refer to “pairing”). Open the battery cover Insert the button battery 2. After pairing is complete, check if the LED is lights up each time you move two pieces close to/apart from each other.
PAGE 5
3.During installation, make sure to align the dot marker on each of the two pieces,also ensuring the gap between the two halves is less than 20mm when the door/window is closed. Use spacers to level the two pieces up (shown in diagram).
PAGE 6
Important Tips: 1. Install the contact sensor part onto the fixed non-moving part of the door or window etc (e.g. door frame), with the magnet piece being placed on the moving part (e.g. door). 2. To get realtime notification anywhere you go, an Apple TV (4th gen or above), HomePod or suitable iPad is required as a Home Hub for remote access. VS1 is exclusively compatible with Apple HomeKit. Pairing Connect your iOS device to the internet and make sure Bluetooth is On, then follow the steps below: 1.
PAGE 7
● The device must be disconnected from the supply mains(where appropriate) when removing the battery; ● The battery is to be disposed of safety; ● Using incorrect type batteries can cause damage to people or the accessory. FCC Caution: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 8
IC This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. In order to avoid the possibility of exceeding the ISEDC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.
PAGE 9