VIVOTEK Fixed Dome Series Mounting kit User’s Manual Using AM-518 mounting adapter and compatible accessories Rev. 1.
Revison History: Rev. 1.1: Added Fisheye camera mounting details. Rev. 1.1a: Updated the model names of compatible accessories. Rev. 1.1b: Added supported models, FD8335H, FD8135H, and FD8372. R2.5000 R4.
English II Compatible Accessories Compatible Accessories (1): AM-311 Pole Mount Bracket Compatible Accessories (2): AM-411 Corner Mount Bracket Compatible Accessories (3): AM-711 Junction Box Compatible Accessories (4): AM-212 Wall Mount Bracket 3
Compatible Accessories (5-1): AM-114 Pendant Head Compatible Accessories (5-2): AM-115 Pendant Pipe 4
English III Mounting & Cabling Mounting Hole Definitions Above are the locations of different groups of mounting holes for matching different cameras: Hole Type A B C D Applicable Cameras FD8362E, FD8362, FD8361, FD8335H, FD7141, FD7141V, and FD8372. FD8161, FD7131, FD7132 FD8162, FD8135H FE8171V Align the mounting holes on your mounting plate (outdoor series) or on the camera (indoor series) to match those on the mounting adapter.
NOTE: Due to its unique mechanical design, the mounting procedure for an FE8171V fisheye camera is specifically described as follows: 1. Remove the camera's top cover. 2. Fasten 2 included screws to the D holes (not the D+ hole). 3. Align the camera with the mounting adapter and let the 2 screws enter the key holes located on the side where the camera's cabling interfaces reside, e.g., the Ethernet port. 4. Rotate the camera counter-clockwise.
English Wall Mount Installation Below is a general, sample procedure using a Wall mount bracket: 1. Locate the position where you want to install the wall mount bracket and camera. Drill holes on the wall for securing the bracket and for routing the cables. Secure the bracket by hammering anchors into the wall and then fasten screws through it. 2. Route power lines and other cables through the wall and the bracket. 3.
Below is a closer view on routing cables and matching a mounting plate. Mounting Adapter Wall Mount Bracket Cables FD8362E Mounting Plate NOTE: Use the correct type of screws when installing cameras to the mounting adapter. Refer to page 5 for the screw type. The sample mounting positions for FD8362E (or FD8335H and FD8372) are shown below.
English Shown on the right is an exemplary illustration for the FD8135H and FD1862 indoor cameras. Refer to page 5 for the screw type. Pendant Pipe Installation Below is a sample procedure using a Pendant pipe: 1. Determine a hard surface ceiling location, and use the four mounting holes on the pendant head to mark the positions where holes will be drilled to secure the pendant head. Note that screws are user-supplied and they should be 11mm long at least.
2. Locate the position where you want to install the pendant pipe and camera. Drill holes on the ceiling for securing the pendant head. Secure the pendant head by hammering anchors into the ceiling and then fasten screws through it. 3. Route power lines and other cables through the side bushing and/or conduits (usersupplied), and through the pendant pipe. 4. Secure pendant pipe to the pendant head by rotating it clockwise until it is tightly fastened.
When cabling is done, proceed with initial setup such as enabling network access, focus tuning, or zooming. When done, secure the outer dome cover. 11 English 5. Secure the connection using the included hex wrench. 6. Attach mounting adapter to the pendant pipe by rotating it clockwise until it is tightly fastened. 7. Secure the connection using the included hex wrench. 8.
Corner Mount Installation Below is a general, sample procedure using a Corner mount bracket: 1. Combine the two brackets together using the included nuts and washers. 2. Align the assembled brackets with the desired position. Align screw holes on the brackets against the wall. Drill holes on the wall for securing the bracket and for routing the cables. Hammer anchors into the wall. 3.
English Pole Mount Installation Below is a general, sample procedure using a Pole mount bracket: 1. Route power lines and other cables through the included cable gland, pass them through conduits (separately purchased), and install the cable gland to the pole mount bracket. 2. Locate the position where you want to install the pole mount bracket and camera. Unwrap the stainless belts, feed them through the openings on the sides of the bracket, and then strap them around the pole.